CL drum washing machine 3104010022 faulty E5

F1: Haier washing machine water level sensor is in poor contact E1: Haier washing machine draining timeout, check whether the drain pipe is blocked E2:

The upper cover of the Haier washing machine is not covered well E3: The dehydration of the Haier washing machine is unbalanced, shake the clothes again and spin them again E4: The water inlet of the Haier washing machine is timed out, check the water pressure, and whether the water inlet valve is dirty and blocked E5:

The water temperature of Haier washing machine exceeds 50 degrees E6: Does Haier washing machine use high-foaming laundry detergent Haier drum washing machine failure** [L--1 *Haier drum washing machine manual selection of clothing amount** HTD68, BS68Z L--A *Haier drum washing machine manual clothing quantity selection**, choose when the clothes are basically full HTD68, BS68Z asafe on *Haier drum washing machine start keypad lock function HTD, BS68, SFE OFF * Cancel the keypad lock function of Haier drum washing machine htd, bs68, end * indicates that the program of Haier drum washing machine is over E1 *The door lock of Haier drum washing machine is abnormal htd, bs68, hdy, d08a, d08, d09, bs58, s06a, 60-ht, bs08 Re-close the door and check the door E2 *Haier drum washing machine drain fault htd, bs68, hdy, d09, d08, d08a, bs -ht, bs08 Clean the filter and check the drain pump E2 * Haier drum washing machine water inlet timeout S06A The water valve is not open or the water pressure is too low E3 * Haier drum washing machine temperature sensor is faulty htd, bs68, hdy, d09, d08, d08a, bs -ht, bs08 Contact for maintenance: E3 * Haier drum washing machine drain timeout alarm S06A Check the drain pump or drain pipe for poor drainage E4 * Haier drum washing machine heating fault HTD, BS68, BS58, D09, D08, S06A, 60-HT, BS08 **Check whether the heating pipe line is in poor contact or contact for maintenance E4 *Haier drum washing machine reaches the water level for 8 minutes HDY, the faucet is not opened, the water pressure is too low, and the siphon is siphoned.

Press the start button to continue running E5 *Haier drum washing machine for 8 minutes to reach the water level D08A, D09, D08, BS08 E5 *Haier drum washing machine feed (inlet) water is abnormal HTD, BS68, HDY, BS -HT The water pressure is too low, or the water is stopped. E5 * Haier drum washing machine motor operation abnormal S06A motor protection alarm.

Summary. Hello dear, I am glad to answer for you: What is the fault of the drum washing machine showing E53?

Answer: The failure of the washing machine E53 means that the dehydration is unbalanced. This can be caused by clogged drains, uneven laundry, uneven laundry close to one side, or too much laundry.

There is also a reason that the washing machine switch of the magnetic switch is damaged. The workarounds are as follows:1

Press the lid switch by hand to make sure it is working properly. If the washing machine thinks the lid is open, it won't drain water. To check if the lid sensor is damaged, locate the part that was pressed when the lid was closed.

Then, press this switch and listen for a click or check the "lid off" indicator on the washing machine, depending on your model. If your switch doesn't seem to be working properly, it may be that the cover switch is broken and needs to be replaced. 2.

Before inspecting other parts, unplug the washing machine to prevent electric shock. Move the washing machine away from the wall so you can reach the power cord. Carefully pull the power cord out of the socket so that the washing machine is not connected to the power source.

This will limit your risk of electric shock while working on the machine.

Hello dear, I am glad to answer for you: What is the fault of the drum washing machine showing E53? A:

Washing machine E53 fault means dehydration is unbalanced. This can be caused by clogged drains, uneven laundry, uneven laundry close to one side, or too much laundry. There is also a reason that the washing machine switch of the magnetic switch is damaged.

The workarounds are as follows:1Press the lid switch by hand to make sure it is working properly.

If the washing machine thinks the lid is open, it won't drain water. To check if the lid sensor is damaged, locate the part that was pressed when the lid was closed. Then, press this Tomb switch and listen for a click or check the "Lid Off" indicator on the washing machine, depending on your model.

If your switch doesn't seem to be working properly, it may be that the cover switch is broken and needs to be replaced. 2.Before inspecting other parts, unplug the washing machine to prevent electric shock.

Remove the washer away from the wall so you can reach the power cord. Mu Pie carefully pulled the power cord out of the socket so that the washing machine did not connect to the power source. This will limit your risk of electric shock while working on the machine.

3.Bucket or pot to remove the water from the washing machine. You need to drain the machine before you can operate it.

First, remove any laundry that is still in the drum of the washing machine. Then, use a plastic bucket or cauldron to scoop the water out of the machine. Dispose of the water by pouring it into the sink or bathtub.

4.Over time, debris can clog drain hoses and prevent the washing machine from draining. Twisted or coiled drain hoses can also impede the free flow of the water mill.

Inspect the slag behind the washing machine and straighten the kinked hose.

It may be that the computer board has failed to close the door, and this fault should be done by reclosing the door of the washing machine, and the problem will not be solved until the washing machine is fully closed. There is also a possibility that the circuit board or motor of the washing machine was burned out by the hall wheel.

1. When the washing machine shows the fault **E30, it should be paid attention to. You should check whether the hatch of the washing machine is closed, if it is not closed, it will show the fault**After closing, if the Tongsheng washing machine still shows this fault**, you should consider whether there is a problem with the computer board of the washing machine.

2. Check the computer board of the washing machine to see if it can operate normally, if it is not able to enter the operation, you need to find a professional master to repair the computer board of the washing machine. After the computer board is repaired, see if the washing machine can run normally. If it doesn't run properly, then the motor of the washing machine has burned out.

3. After the motor of the washing machine burns out, you need to replace it with a new washing machine motor, after replacing the washing machine motor, the washing machine can operate normally, you must remember that the motor of the washing machine must be replaced with the same model, otherwise it will not be able to run normally, if the motor is replaced, or can not work normally, check whether the drainage pipe or drainage solenoid valve is blocked, and dredge the drainage pipe or drainage solenoid valve.