Haier copper washing machine process to dehydration, can not be dehydrated, is there the fault?

1. The switch of the top cover is damaged, and the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move!

2. The drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, if the water level switch is damaged, you will not be able to enter the dehydration program!

3. The washing and dehydration of the automatic washing machine is completed by converting the gear at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

4. The computer control board is malfunctioning! It can only be replaced, because its control panel is covered with glue in order to be waterproof, and it is quite inconvenient to repair!

I hope it will be helpful to you!

Addendum: If there is still an unfinished program, once you press the start of the drum washing machine, he must finish the program, otherwise the door will not be opened. Now, here's what you have to do:

In the case of power failure, open the baseboard on the lower right foot of the washing machine door, and then turn the twist of the emergency drain pipe in the counterclockwise direction, so that the laundry detergent in the washing machine can be discharged from the washing machine (Note: water such as water in a basin).When the water is drained, the washing machine door will naturally open.

Check that your washing machine is flat (note not stable) and that the clothes are not too many and uneven. If there is a problem with the computer board, it is recommended to contact customer service to check it.

It's okay to let the after-sales service come to show you, and it's difficult to repair it yourself if you know the fault.

1. First of all, check whether the drain pipe of the washing machine is blocked, the water discharged from the washing machine contains debris of clothes, hair and other debris, which may cause the blockage of the sewer, resulting in the water cannot be discharged, and the washing machine cannot be dehydrated.

2. Check whether the cover of the washing machine is closed, for safety reasons, the washing machine will detect whether the cover of the washing machine is closed when dehydrating to prevent the danger of high-speed rotation of the inner cylinder, so close the cover and the washing machine will be dehydrated.

3. Check whether there is too much clothes inside the washing machine, the washing machine has its own rated load, and after exceeding the capacity that can be washed, it will cause the washing machine motor to not work, and it will not be able to dehydrate.

4. Check whether the clothes inside the washing machine are evenly placed, if there are large absorbent clothes in a corner, it will cause the center of gravity of the inner cylinder of the washing machine to be seriously cheap, resulting in dehydration cannot be carried out.

5. If the above points have been checked, then observe the washing state of the washing machine, whether the washing machine can turn left and right normally, if there is only one direction of the wave wheel rotation during washing, then it is likely that the control panel of the washing machine is faulty, please warrant.

If there is no problem with the left and right turns of the inner drum of the washing machine when washing, then it is likely that other mechanism parts are damaged, please also ask for warranty.

Reason: It may be that the location of the drain pipe of the Haier washing machine is blocked by something, and the foreign matter in the drain pipe can be cleaned up. It may be that the water purification valve of the Haier washing machine is faulty, and the washing machine will enter the water again when it is dehydrated, and the washing machine will be dehydrated and not dry.

It is also possible that the capacitance of the Haier washing machine is damaged, and the water will not dry out if it turns slowly during dehydration. Solution: 1. The washing machine is washing a single piece of clothing, especially the water content.

When there are more sweaters or underwear, there is sometimes no spin-off phenomenon, which is a drum washing machine.

eccentricity protection function. The eccentricity protection feature is a feature that all front-loading washing machines have. 2. The washing machine can automatically detect the eccentricity value of the washed clothes when spinning drying, if the clothes are unevenly distributed, the washing machine will shake and distribute the clothes again, and then spin dry when the clothes are evenly distributed; If the laundry is not evenly distributed, it will cause the washing machine to vibrate and shift, and it will damage the washing machine or other items around the washing machine.

3. If there is eccentric protection in the washing machine, you need to check whether the clothes are knotted and entangled, and rearrange the clothes, and then choose the spinning program for spinning; When there are fewer clothes, due to eccentric protection, the washing machine may not be spun dry, and some clothes can be added to make the clothes evenly distributed, and then spin drying; In addition, the washing machine will cause the drying time to be extended due to the re-shaking and distribution of the laundry, which is a normal phenomenon set by the program, so please feel free to use it.

1. The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed movement when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover circuit is opened. If it is damaged, it will cause the Haier washing machine to stop suddenly when it is dehydrated.

2. The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the bucket cannot be excluded, or there is too much foam in the bucket, and the washing liquid in the cylinder is difficult to drain for a while, and the water level switch cannot be compounded, which will cause the washing machine to stop suddenly when it shouts pure washing until dehydration. The washing machine cannot enter the dehydration program.

Reasons why Haier drum washing machines stay at 5 minutes for dehydration:

If it has been dehydrated, then it should be a problem with the computer board, if it is not dehydrated, the clothes are still quite wet, then it may be a computer board or a speed control module, of course, the motor is also possible. You need to find a maintenance person to deal with it.

The cause of abnormal dehydration of the washing machine can also be found according to these methods:

1.Check whether Zheng Kai's washing machine is placed smoothly, regardless of whether the ground is flat or not, the washing machine must be perpendicular to the horizontal plane.

2.Check whether the clothes in the bucket are placed unevenly, resulting in dehydration, shaking and noise, at this time, the cover should be opened, and the clothes should be evenly placed on the walls of the bucket around the bucket.

3.Check that the four nonsense booms on the bucket are consistent, and they should be adjusted consistently. Whether the spring elasticity is the same, if the elastic force is not the same, the new spring should be replaced with the same elastic force. Trouser bush touch.

4.The balance ring on the top of the dewatering bucket ruptures or leaks, causing the dewatering bucket to lose its balance when it rotates. Just replace the balance ring and it will solve the problem.

5.Check whether there is a foreign substance between the inner barrel, the wave wheel and the outer barrel in the same way as if there is a noise in washing, and if there is a foreign body, remove it.

Data expansion: The drum washing machine is controlled by a microcomputer, the clothes are not entangled, the washing is uniform, and the wear rate is 10% smaller than that of the wave wheel washing machine, which can wash cashmere, wool, silk and other clothes to achieve comprehensive washing. It can also be heated to fully dissolve the laundry detergent and give full play to the decontamination effect of the laundry detergent.

It can form a highly concentrated laundry detergent in the bucket, bringing the ideal washing effect while saving water. In addition to washing and dehydration, some drum washing machines have functions such as disinfection and sterilization, drying, and upper drainage, which meet the needs of consumers in different regions and living environments.

Drum washing machine, originated in Europe, the laundry method is designed to imitate the principle of rod hammer hitting clothes, by stainless steel inner barrel, mechanical program controller, phosphating, electrophoresis, spraying triple protection of the shell, and a number of bulky cement blocks are used to balance the huge centrifugal force generated when the drum rotates to do repetitive motion, plus the joint action of washing powder and water to make the clothes clean.

Hello dear Haier drum washing machine can not be dried (dehydrated) normally for the following reasons: 1. The washing machine is not energized; 2. The drainage pipe is bent or blocked; 3. The washing machine is suspended; 4. The washing machine is in the anti-wrinkle soaking program. You can troubleshoot them in the following order:

1. Check whether the washing machine is powered on and whether the indicator light on the panel of the washing machine is on; 2. Please check whether the drain pipe is bent or blocked and cannot be drained, put the drain into the floor drain to see if the drain can flow out of the water, if it cannot mean that the drain pipe is blocked, please dredge the drain; 3. Please check whether you press the pause button of the washing machine, start whether the pause indicator is flashing, if it is flashing, please press the start button once; 4. Please check whether it is in the anti-wrinkle soaking program, if the anti-wrinkle soaking indicator light is on, please press the anti-wrinkle soaking button again. Extended information: Splinting, also known as dehydration, mainly uses the centrifugal force of the high-speed rotation of the dehydration bucket to remove part of the moisture on the clothes.

Spin drying is not the same as drying, drying can completely evaporate the water on the clothes, spin dry can only throw out part of the water. The drum washing machine originated in Europe, the washing method is designed to imitate the principle of rod hammer hitting clothes, using the mechanical work of the motor to rotate the drum, and the clothes are constantly lifted and dropped in the drum, and then lifted and fallen, doing repetitive movements, plus the joint action of washing powder and water to make the clothes clean. Wheeled washing machines, on the other hand, need water to float the clothes, and then stir and rub them to clean them.

The arc motion of the drum washing machine during spinning produces a centrifugal effect, and it must provide an external force to provide a centripetal force to maintain this arc motion. The original spin drying is to use the spin drying bucket under high-speed operation, so that the clothes in the barrel follow the high-speed operation, and the water of the fabric fiber is thrown away under the action of centrifugal force, so as to achieve a dehydration and drying effect.

Summary. Haier drum washing machine can not be dehydrated normally Reason:

1. When the washing machine is not dehydrated, first check whether there is water in the washing machine, and if there is water, you can open the drain valve first to see if there is any foreign matter inside.

Method: To disconnect the power supply, you can first open the front baffle of the washing machine and unscrew the drain valve in the lower right corner to drain the water. Generally, the computer board of the washing machine will show a "5e" fault if there is no drainage**, if there is a foreign object, install the drain valve switch after taking it out, and the test machine should be normal.

2. If the clothes are placed too little or not released, the washing machine will be unbalanced when it is dehydrated, but the washing machine itself can still be balanced.

In this case, the method is: open the door to take out the clothes and shake them into the single dehydration program that can restart the washing machine, and the washing machine will readjust the dehydration after starting, and press the washing machine to see if it is placed stable. If the above two situations cannot be solved, the performance of the washing machine may be faulty, and an engineer needs to come to repair it.

Why can't Haier drum washing machines spin normally?

Hello, I have seen your question and am sorting out the answer, please wait a while

Reasons why Haier drum washing machine cannot be dehydrated normally: 1. When the washing machine is not dehydrated, first check whether there is water in the washing machine, and if there is water, you can first open the drain valve to see if there is any foreign matter inside. Method:

To disconnect the power supply, you can first open the front bezel of the washing machine, unscrew the drain valve in the lower right corner, and drain the water. Generally, the computer board of the washing machine will show a "5e" fault if there is no drainage**, if there is a foreign object, install the drain valve switch after taking it out, and the test machine should be normal. 2. If the clothes are placed too little or not released, the washing machine will be unbalanced when it is dehydrated, but the washing machine itself can still be balanced.

In this case, the method is: open the door to take out the clothes and shake them into the single dehydration program that can restart the washing machine, and the washing machine will readjust the dehydration after starting, and press the washing machine to see if it is placed stable. If the above two situations cannot be solved, the performance of the washing machine may be faulty, and an engineer needs to come to repair it.

Hello dear, the following is the information for your inquiry. There may be several reasons why Haier washing machines are dehydrated and dry: 1

Failure inside the washing machine: If there is a failure inside the washing machine, such as a motor problem or a damaged transmission belt, it can lead to poor dehydration. 2.

Incomplete filter cleaning: The filter inside the washing machine can become clogged with dirt and dust, which can affect the washing machine's ability to dehydrate. Therefore, you need to clean the filter frequently.

3.Excessive laundry load: If you fill or overload your washing machine, it can affect the dehydration effect.

Pay attention to the maximum capacity of the washing machine to avoid this from happening. 4.Water Leakage Problem:

If the washing machine has a water leakage problem, it may affect the dehydration effect. Check the water pipes and drains of the washing machine for leaks, and if so, repair them in time. 5.

Unstable placement of the washing machine: If the washing machine is placed unsteadily, it may cause the washing machine to shake during operation, which will affect the dehydration effect. Please make sure that the washing machine is placed on flat ground.

If your Haier washing machine has a problem with poor dehydration, it is recommended that you check these possible causes first and repair or clean them according to the specific situation. If the problem persists, please contact the after-sales service center or professional maintenance personnel for maintenance.