How to install a wireless router in the community fiber network!

Here's how to install it:

1. After powering on the wireless router, log in to the wireless line router on the mobile phone or computer, change the LAN port address of the wireless router to avoid conflicts with the LAN port address of the optical modem, save it, and restart the wireless router;

2. Connect the network cable from any LAN port of the fiber modem to the WAN port of the wireless router, and then connect the network cable from the LAN port of the wireless router to the computer, and the IP address and DNS settings of the local connection of the computer are automatically obtained;

3. Open the browser, enter, enter, enter the default login username and password of Tengda wireless router to enter the wireless router setting interface;

4. The next step of the setup wizard, the general household is to choose the ADSL virtual dial-up (PPPOE) mode, the next step, enter the Internet access and password provided by the network ** provider, the next step, set the wireless network name in the SSID box, select the WPA-PSK WPA2-PSK encryption mode, enter at least 8 digits of the wireless password, the next step, save, restart the wireless router to complete the installation.

I'm in Henan, Henan Netcom Optical Fiber, Henan Netcom needs to be converted through a number calculator, and then set the password to the router on the line, the password is your login password, don't forget the security settings in the parameter settings, and set a password for the router.

At present, most of the optical fiber access used in China uses FTTB technology. So you don't need to have dial-up hardware like cats at home. So you can use a router and set it up the same way that the original adsl pppoe server dials up.

Because FTTB also has a username and password like ADSL.

Wall panel - wireless router WAN port - desktop electrical LAN port.

Log in to the router's web settings interface, follow the wizard prompts to select PPPoE, and enter the password.

Enter the wireless router management page.

The WAN and LAN cannot be on the same network segment if they need to be reset again.

The WAN is set up according to the requirements of the community.

The MAC bindings in the WAN must be set correctly.

You can set the LAN to another CIDR block.

The local computer should be set accordingly, changing the gateway, DNS, etc. of the local computer.

Make sure the wireless function is turned on.

Make sure the wireless protocol is correct.

The wireless default channel is generally 6

Sometimes there will be conflicts with neighbors, and they can be replaced.

To avoid incorrect wireless settings, make sure that the wired can be used normally.

The steps to connect and set up the fiber broadband modem and wireless router are as follows:

1.First connect the line, you can refer to the figure below.

5.Enter the account and password applied for from the network service provider, and go directly to the next step after entering.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The method of connecting the optical modem to the wireless router in the cell

1.Connect the WAN port of the router to the LAN port of the optical modem with a network cable, and when the WAN port light of the router flashes, the connection is normal.

How to configure a wireless router:

1.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

2.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

3.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

4.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

As shown in the preceding figure, the home optical fiber is connected to the modem--- the modem network cable is connected to the WAN port of the router--- the LAN port of the router is connected to the network cable to each Internet device.

Wireless Router Setup Method - ADSL Virtual Dial-Up Subscriber.

The connection needs to be used (a cat.

2 LAN lines.

The LAN cable is connected to the computer network card.

The LAN port of the cat is connected to the WAN port of the wireless router.

The LAN port of the wireless router is connected to the computer network card.

OK then power on the wireless router and power on the cat again, OK, and then you set it up according to the router manual. Original, please don't copy, it's hard to play.

No need for cats, after the wireless routing is set up (it is best to add a password to prevent rubbing the network), the notebook installs a wireless network card, generally about 100 (it is better if there is), search for signals, enter the password on the line.

Optical fibers cannot be directly connected to routers, and optical fibers need to be connected to the modem and dial-up to the Internet through the optical modem. The modem connects to the router through a network cable.

Swap your router into a switch and plug it in to use 3 machines.

No cats,Follow the instructions in the manual,Enter in the browser or enter the router settings page,Set the Internet access method in the setup wizard,You choose to let the router identify itself,You don't need to enter the password or anything,There is an option to set the wireless signal name and password in the middle,Remember to fill it in,What channel or what's the default can be。

Fiber optic to the cat--- cat to the router --- computer.

1. The optical fiber of the community is generally the local area network of the community, and the network cable connection is 100m to the home, and then the network is connected by virtual dial-up.

2. Therefore, your network can directly connect the network cable to the wireless router, the desktop computer can access the router, and the notebook can use wifi wireless Internet access, which is very convenient and no longer needs an external ADSL cat.

3. It is relatively simple to set up, and the instructions are generally written in more detail. Generally, use a browser to enter the web settings interface, set PPPOE dial-up, and then set the computer IP to automatically obtain, you can directly surf the Internet (of course, you can also set the IP to be the same network segment as the IP of the router).

If you look carefully at the manual, the settings of different brands of routers are slightly different, but they are all the same.

Hope it helps.

The cell broadband breakout line is directly connected to the WAN port of the router, and the MAC address cloning of the router is enabled, and in the case of ordinary broadband dial-up or fixed IP, the user name or IP can be entered to connect normally.

If the cell authentication mode is dynamic dialing + fixed IP, routing is not supported.

Is your cell-based fiber dial-up?

If you dial up, you need to set the account password in the router.

If it's dial-up, use this method, as long as it's an XP system.

Generally, it is good to set it according to the router manual.

You just plug the fiber into the wireless router and then go to the router interface to set it up.

Fiber-to-the-home plug plug into the crystal head of the computer and plug it into the WAN port of the router.

Set up routing autodialing, a wireless. That's it.

It depends on whether your fiber runs 100m, 1000m, or 10000m.

First of all, to set up a cell network, you need a NAT network address translation device (because your public network IP address is not so much, each person is assigned an IP is definitely not enough), the general community broadband is best to use a dedicated firewall to do this work, but also can play the corresponding network management function on the device, if the number of users is small, more than a dozen people can also use the NAT provided by ordinary routers, I really think that the firewall is too expensive to do a soft route, now routos, Sea spider software configuration a new and capable computer or server, the running effect is okay.

Secondly, you need to select your switching equipment and media conversion equipment (optical fiber), if your switching equipment can install optical fiber modules and can communicate with the network card on your firewall and the optical film on other switching equipment, then you can choose the optical fiber module plus switch mode that uses a certain brand of bandwidth between the switch equipment. If you want to save money or should have hardware incompatibility problems, you can also use the media converter plus switch mode.

To put it simply, you should need the following equipment.

A firewall or router connects to the egress for network address translation and cell network IP address assignment (DHCP).

Per drain (switch + fiber module + fiber connection) or (switch + fiber transceiver + fiber connection) mode. Finally, the switches are connected via fiber to the core switch or firewall.

Each user is connected to the vulnerable switch via a network cable or fiber optic fiber.

The telecom room lays fiber to the cell.

--The optical fiber needs to be connected with the pigtail with the terminal box, and the pigtail dissolved by the terminal box is connected to the optical transceiver--- and the optical transceiver can be connected to the router with a network cable.

Also: optical transceivers are provided by telecommunications.

The installation and operation method of the optical fiber cat wireless router is as follows:

1. Log in to the TP--Link wireless router and change the LAN port address to avoid conflicts with the LAN address CIDR block of the optical modem.

2. Connect the network cable from the LAN port of the optical modem to the WAN port of the wireless router, and connect the network cable from the wireless router to the computer (if it is a notebook debugging, it can be directly debugged by connecting the wireless router through the wireless signal), and automatically obtain the IP address and DNS settings of the local connection of the computer;

4. After entering the wireless router, click on the left column to set up the wizard, next, select ADSL virtual dial-up (PPPoe) Internet access mode, next, enter the broadband account and password, next;

5. Set the wireless network name in the SSID box, enter the wireless network password with at least 8 digits in the psk box, and the next step;

6. Save, restart the wireless router according to the prompts to complete the installation of the wireless router.

Here's how to set up a secondary wireless router:

Set up wireless router mode.

Connect a network cable from any LAN port of the first router to the WAN port of the second wireless router, enter the second wireless router, select dynamic IP Internet mode, enable the DHCP server, save, and restart the router.

Set up the wireless switch mode.

Connect a network cable from any LAN port of the first router to the LAN port of the second wireless router, enter the second wireless router, and shut down the DHCP server.

You connect the incoming cable to the WAN port of the first wireless router. Then enter the wireless router to set up the WAN port, and you can do it.

to bridge the settings.

Two routers are bridged.

The home line is connected to the wireless router WAN port, and the home computer is connected to the LAN port, and the IP is set to automatically obtain, and it is entered in the browser.

Go to the Wireless Routing Configuration page and configure the route. Including WAN setup, LAN setup, wireless setup. All you need is one route.