What should I pay attention to when laying underfloor heating? How cost effective is the floor heati

The laying method of floor heating is: 1. Before the water and electricity enter the site, the owner + home decoration designer + home improvement project manager + heating technician will carry out on-site positioning and disclosure; 2. Clean up the garbage on site after the completion of hydropower construction; 3. The first phase of heating is used for construction and distribution of pipelines (a, laying insulation benzene board, b, laying mirror reflective film on the insulation benzene board, laying insulation edge strips on the edge of the corner, c, laying pipes on the mirror reflective film, d, fixing the nail on the pipeline, e, carrying out pressure test, the standard of pressure retention is: the minimum experimental pressure shall not be lower, generally can be raised, and then stabilized for 30 minutes, the pressure reduction does not exceed, and there is no water leakage, that is, it is qualified.

4. The decoration masons enter the site for cement leveling construction.

The first ** is the construction of floor heating module**; The second is the construction of conventional thermal insulation benzene board for floor heating**.

1. Before installing the graphene floor heating system, it is necessary to ensure that the hydropower construction of the whole house is completed and passed the acceptance;

2. The interior decoration has been completed with wall brushes, and the exterior windows have been installed;

3. Ensure that the floor heating installation and construction area is neat and clean, and any equipment, materials and sundries that affect the construction, such as wires, should be removed;

4. The ambient temperature of floor heating installation should not be lower than 5 °C;

5. Due to the characteristics of graphene floor heating itself, cross operation with other types of work should be avoided, and the required holes in the back should be retained;

6. The heating film must be shading when transporting, and should not expose a large amount of packaging, and ensure that it can be handled gently when moving;

7. When stored at normal time, the temperature should not exceed 40°C, and ventilation should be ensured, and it must be protected from damage by physical pressure.

1. What are the advantages of floor heating module?

1) Energy saving and fast heating.

No nails are used, the insulation layer is not damaged, and it is more energy-saving. The pipeline is suspended to increase the cement contact surface to speed up heat dissipation.

2) Product integration.

The number of construction nodes of integrated modules such as extruded plastic boards, reflective films, and clamps has been reduced from 7 to 2 to improve construction efficiency and quality.

3) There is color and material.

Standardized construction site management is simpler. The coil spacing can be adjusted, and the turning angle is consistent, which reduces the water resistance and avoids dead breaks.

4) Safe and comfortable.

The pipe is embedded to avoid damage during construction. Thinner and less occupy a high floor height, increasing living comfort.

2. How about the floor heating module.

1) The floor heating module has a little greater advantage than ordinary floor heating, and the floor heating module has two kinds of dry floor heating and wet floor heating, of which dry floor heating is characterized by no need for backfill layer, which reduces the layer height, and the load-bearing is also reduced, which is also ultra-thin floor heating.

2) The base material used is mostly composed of high-density thermal insulation and environmental protection materials and aluminum plates, and when there is a failure, contact the after-sales service to provide Master Wan service, so as to facilitate maintenance.

Three indicators for choosing a floor heating module: thermal insulation, compressive resistance, environmental protection and thermal insulation: the module must have an insulation layer, generally made of EPS (polystyrene board) or XPS (extruded plastic board) material.

The density of extruded board should be greater than 32kgm. The insulation layer of the INS warm module is EPS, and the density is 35 kg m

Compression resistance: the requirement is greater than 200kpa, and there are basically no footprints when people step on it. The harder the insulation board, the better, and the heat retention may be lost if the hardness is too high. The compressive resistance of the Eswarm module is 220kpa.

Environmental protection: If the extruded board is used as the substrate, it is best to choose the white crystal board. Polystyrene board is difficult to produce due to process materials. The Eswarm module is made of environmentally friendly primary raw materials that can come into direct contact with food.

Answering the modular floor heating, the backfill layer is not only to protect the pipes, but also to absorb heat and store heat, and then as a super large heat dissipation plane, the heat is transmitted to the air in the room and objects such as the home through heat radiation and heat conduction. Therefore, modular underfloor heating is a more stable and comfortable heating method.

Some of the questions said: the module of modular floor heating hinders the heat dissipation of the water pipe, can not dissipate heat to the surroundings, unlike ordinary floor heating, the water pipe is not bound by the module, can be fully placed to dissipate heat, is there such a thing?

In terms of traditional floor heating, the heat dissipation of modular floor heating will be better. First of all, the traditional underfloor heating is to combine the underfloor heating of the room, living room, toilet, and kitchen. Therefore, once the underfloor heating is turned on, the temperature of the room will rise immediately, and even if the underfloor heating is turned off, the cooling will be very slow.

But modular floor heating is different, the floor heating of the room is the floor heating of the room alone, and the living room has a separate floor heating in the living room. Because the heating area is small, it cools down quickly.

Question: Ordinary floor heating is that the water pipe is fixed on a flat plate, and you can also walk all the way in a room, ordinary floor heating and modular floor heating are all the way in one room, which is better and more energy-saving?