How to change the signal of your iPhone to a dot

Method: 1. Dial keypad input: *3001 * point call.

2. The mobile phone will automatically switch to the field test startup page, and the signal strength value will be displayed in the upper left corner.

3. The dotted signal grid is gone, but the revolution has not yet been completely victorious, so let's go down.

4. Start holding the top power key of your iPhone until the "Slide to power off" slider appears. Don't let go.

5. After the "slide to power off" slider appears, the power button will not be released and press and hold the home button at the same time.

6. Press and hold the two buttons at the same time for about 5 seconds, and the phone will restart.

7、ok!8. The recovery dot icon only needs to click on the number to switch.

Note: Dialing once may not be successful, you can dial twice more! Be sure to re-enter and do not use the replay function.

Recovery Dot Icon Method:

1. Dial pad input: *3001 * point call.

2. The phone will automatically switch to the field test startup page, press home directly to exit, and you're done!

1. Tap "**" on the standby page of the phone, enter *3001* in the dial pad, and then press the "Call" button.

2. Then enter the signal digital display interface, press the "home" button of the mobile phone to return, then you will see the signal of the iphone5s change from the number back to a small dot.

That's after upgrading to ios7, your current system should be ios7 or below, right? If the phone is a mobile phone below iphone4s, it is recommended not to upgrade, it will be stuck! Satisfied!

Take iPhone 6 as an example, the setup method is as follows:

1. Turn on the mobile phone, at this time, you can see the signal in digital mode in the upper left corner of the mobile phone desktop, and then click the icon of "**" to enter.

2. After entering the dialing interface, the input state will definitely rise to "*3001 *", and then click to dial ** macro.

3. At this time, the mobile phone interface will display the following picture.

Fourth, then return to the mobile phone desktop, in the upper left corner of the old desktop you can see that the signal has become a small dot mode.

Take the Apple 6 phone as an example.

Procedure. 1. At the beginning, first find the "**" icon of the program that should be used on the desktop core spine of the mobile phone, and click to enter the new operation interface.

2. Then, after entering the **operation interface, enter **"*3001*" in the dialing keypad, and click the dialing icon option after the change.

3. At this time, the interface will jump to field test, which means that ** has taken effect.

4. Next, return to the desktop of the mobile phone, and you can see that the signal has become a small dot.

How do you change the signal of an Apple phone to a dot? After a few friends changed the signal icon of the lead shed iphone to a number, they didn't know how to change it back to a dot. Let's take a look at it with me.

1. First click to open [**].

2. Enter [*3001 *] on the dial pad and click [Dial].

3. After entering the special interface of Xianbi, do not click on English, click directly on the upper left corner to return, or press the home button to return.

4. After returning, you can see that the signal logo has become a dot.

Note:System signals above ios11 cannot be turned into dots, and the ios11 signal grid is vertical, and it cannot be modified to the display mode of dots.

You can follow the steps below to change the signal icon back to a dot.

Step 1: Turn on the phone's hidden number function.

Step 2: Click on the dial pad below to enter the dialing interface.

Step 3: Enter *3001* on the dialing screen and click Dial below.

Step 4: After that, the mobile phone will enter the field test page shown in the picture, and then click on the upper left to return to carry the infiltration "**".

Step 5: After that, the letter chichong icon will change back to a small dot.

Apple's signal is changed back to a small dot, and the operation steps are as follows:

1. Open the desktop of Apple iOS, click on the [Settings] page, see the [General] option in the [Settings] page, and click to enter.

2. At the bottom of the [General] page, see [Accessibility] and click to enter.

3. After clicking [Accessibility], swipe down the dynamic jujube code screen.

4. Pull down on the Accessibility page, you can see which is closed on the right side of the [AssistiveTouch], so the dot does not exist, click to enter.

5. Click to enter the [AssistiveTouch] page, and click to open the switch button in the upper right corner.

6. After turning on [AssistiveTouch], Apple's signal will change back to a small dot, and you can set the transparency when not in use.