The Epson 1600K3 printer lights are all on

Hello: If the printer does not feed paper, the normal boot indicator lights are all on. Please follow the steps below to test.

First of all, turn off the printer and take out the ribbon, and then turn on the printer without installing the ribbon to see if the indicators are all on.

If the indicator light is normal, only the font light is on, it is the normal state of the printer. You can feed the paper to print the test. If the printing is normal, it means that the ribbon is not installed properly, please reinstall the ribbon or replace the ribbon for testing.

If the ribbon is not installed and turned on, the indicator lights are still all on. Please restore the printer to factory settings for testing. Here's how to factory reset your printer:

First turn off the power of the printer, then press and hold the "Font" and "Cut" keys at the same time, hold down both keys at the same time, then turn on the power of the printer, and let go when you see the light on the control panel of the printer.

If it is normal after factory reset, please reinstall the ribbon and print the test.

If the indicator lights are still all on after the factory reset, please print the self-test page to the printer for testing. The printer prints the self-test method as follows:

Turn off the printer first, and then disconnect the cable. Press and hold the "Line Break, Page Change" key and turn on the power of the printer, let go when you see the light on, put the paper, and the printer will print out the content. If there is a "Song font" or "black font" in the first line of the printed content, it is normal, or the printed content is a very regular arrangement of numbers, letters, characters, and Chinese characters are normal.

If not, there may be a problem with the printer.

If the printer light is on after feeding, pay attention to whether the out of paper light is flashing or on. If the paper light is flashing, the printer is jammed, please test it according to the following method:

First, make sure that the thickness of the paper you are using matches where the printer paper thickness lever is placed. When printing a single layer of plain copy paper, the paper thickness adjustment lever is placed at the 0 position. When printing multi-copy paper, the position of the paper thickness adjustment lever is the same as the number of copies (i.e., the copy paper is 2 layers of "original + 1 copy", the paper thickness adjustment lever is 1, and so on).

Secondly, please follow the following method to perform a printer self-test to confirm whether the printer has a hardware failure:

1 Make sure both the printer and the computer are turned off;

2.Load continuous paper or A4 sheets in the correct way in the feeder.

3.Press and hold the Wrap button and then press the power button to turn on the printer. When the printer is powered on, release both buttons.

Normally, the printer will print the self-test page. If paper jams persist, it is recommended that you remove the ribbon and reprint the test.

If the paper feeding and printing actions are normal, it means that the paper jam is caused by the ribbon cartridge not being installed correctly, please reinstall the ribbon or replace the ribbon to install and test again.

If the paper still cannot be fed, the printer has a hardware fault, please contact the Epson Authorized Service Center for further testing of the printer. You can browse the following** to see the nearest service center:

Epson printer has not been used, not very clear, I personally think Canon printer is good, I have been using Canon, Canon's printer is more open in design, I personally prefer MG6180 this, gorgeous appearance, unique ink tank design makes office and home more environmentally friendly, there is currently a free trial activity of "fun printing and happy life", there will be a lot of printer trial experience and experience shared by the applicable people, the landlord will now go to Sohu and so on** to learn more about it!

Can it be used when it is turned off and turned on again?

Situation 1: All indicators are solid on.

When this prompt appears, it means that the device responsible for collecting waste ink inside the printer is full, and you need to contact an Epson authorized service center for professional maintenance of the printer, you can browse the following ** to view the nearest service center:

Situation 2: All lights are flashing.

It is possible that the print head cannot be returned to its position due to foreign objects inside the printer.

Please do the following:

1.If it is a new product, please make sure that the blue tape on the inside and outside of the product has been completely removed;

2.Turn off the printer, open the printer cover, and remove the paper or other obstructions from the paper tray channel.

3.Check that the cartridge hatch cover is tightly closed: Open the cartridge hatch cover, push the cartridge down until it locks into place (with a click), and close the cartridge hatch cover until it clicks.

4.Turn the printer back on and check if the indicator status is back to normal. If the fault persists, please contact an Epson Authorized Service Center for further testing of the printer. You can browse the following** to see the nearest service center:

Pay attention to the working environment temperature in winter, the working environment temperature of the printer is between 10-35 degrees, when the temperature is too low, the lubricant of the printer cart guide rail solidifies, which will also affect the movement of the font car, please place the printer at the normal temperature for 1 hour before use).

The reason why the three lights of the Epson printer lq630K keep flashing is that there is a regular error.

The workaround: Turn off the printer and wait a few minutes before turning the printer on. If the disturber obstacle is still there, it needs to be repaired. When this buffer potato, you can check the information of the Epson certification service organization through the official **, and go to the designated service organization for maintenance.

Epson printer lq630K three lights keep flashing,**Something is wrong? Hurry, hurry!

Possible causes and repair methods: 1. If there is a problem with the motherboard, check whether it has been restored after replacing the motherboard. 2. Turn off the machine and remove the ribbon, turn on the device without trapping the ribbon to see if there is this problem, if it is normal, it is recommended to reinstall the ribbon or replace the ribbon test.

3. If all lights are still flashing when the ribbon printhead is removed, it is recommended that you restore the factory settings for testing: the method is: press and hold the paper in and out of the state in the shutdown state + wrap the line and page + pause + turn on, and let go after five seconds.

4. Change the print head or head cable of the printer to see if it is restored.

When replenishing the ink, please fill all the colors, otherwise the ink will run out and the printer will not alarm, and if you continue to print, air will enter the ink path, which will affect the printing quality. Again**Epson ink clearing software, detailed steps:

2. The interface under the width of the hole appears.

3. Press OK to display the following interface.

<>5. Here we choose to clear the waste ink pad counter.

6. Press OK, turn off the power of the printer according to the prompts, disassemble and restart printing, the ink lamp and the paper feed lamp will no longer flash alternately, and the zero will be successfully cleared.

Summary. The printer cartridge light is flashing, and the fault is related to the cartridge. Or the printer doesn't recognize the cartridge, or the ink runs out and needs to be refilled.

Click Print, and the computer will display the specific cause of the failure.

The printer does not recognize the ink cartridge: most of the ink cartridge chip contacts are not in good contact. Unplug all inner cartridges and reinstall them.

Prompt to replenish ink: Click "How to", follow the prompts step by step, the printer cartridge counter is reset, and you're good to go.

If you just add ink and don't follow the prompts, the cartridge counter won't reset to zero, and the printer will still think that no ink has been added.

What is the reason for the Epson printer L351 ink light flashing?

Hello, I have seen your question and am sorting out the information, and I will reply to you immediately

The ink light flashes to indicate that the ink is insufficient, dear, have you added ink?

Added. Added.

You mean, the ink light still flashes after the ink is added, is it?

Wait a minute, kiss it.

The printer cartridge light is flashing, and the fault is related to the cartridge. Or the printer doesn't recognize the cartridge, or the ink runs out and needs to be refilled. Click Print, and the computer will display the specific cause of the failure.

The printer does not recognize the ink cartridge: most of the ink cartridge chip contacts are not in good contact. Unplug all inner cartridges and reinstall them.

Prompt to replenish ink: Click "How to", follow the prompts step by step, the printer cartridge counter is reset, and you're good to go. If you just add ink and don't follow the prompts, the cartridge counter won't reset to zero, and the printer will still think that no ink has been added.

Hope it helps

Is there a **. Is there a **.

Procedure. Procedure.

Sorry oh dear, the platform doesn't support sending**.

If you have any questions, you can ask me directly.

There is no display problem with the computer.

There is no display problem with the computer.

Reinstall the cartridge and try oh kiss.