The D link router cannot open the web page

Change routers! Switch to TP-link.

I used to use d link, I can get on QQ but not on the web, you can restart the router yourself and it's fine.

This route is cumbersome. But I do not interfere with use.

The IP address in the online neighbor is automatically obtained. Turn off the firewall and try...

If you don't understand, ask me again.

If you are using ADSL access, then you can try other dialing modes in PPPoE dialing mode, such as special mode, etc.; If you are using cell broadband, after you choose the dynamic IP, it is best to give the LAN port IP as something like that.

If you still don't understand, you can contact me.

D link's router is very rubbish, new ones often have problems, if you can change it, it's best to change it, tp-link!

For D-Link wireless routers, the basic configuration is as follows:

1. Log in to the router configuration page.

Open the browser and enter it in the address bar, the default user name of D-Link is admin, and the password is empty.

2. After logging in, choose to manually set up the Internet connection, according to your network access type to set up, there are generally three kinds, 1) DHCP: that is, the operator only provides you with the line, no other information, plug the network cable into the computer to access the Internet, in this case, the access mode is DHCP, and then click Save;

2) Static IP: Static IP, that is, the operator provides you with IP address, subnet mask, gateway and DNS address, then you need to choose the static IP method, and then fill in the above information into the router to save;

3) PPPoE: This is more commonly used, most of them are ADSL, that is, the operator provides you with a username and password, dial-up to access the Internet, then you need to choose the PPPoe method in the router, and then fill in the username and password into the router, and the following connection method selection is always.

As of now, the router can be connected to the Internet, of course, you also have to check whether your physical wiring is correct, and the incoming cable given to you by the operator should be plugged into the WAN (Internet) interface of the router.

3. Set up wireless.

In the wireless settings, you need to change the SSID (wireless network name), and then encrypt it, and it is recommended to use WPA WPA for encryption, and the password is 8 digits or more digits or more digits or letters.

1. Confirm whether the wiring method of the hardware device is correct

The WLAN port of the ADSL or leased line is connected to the router. Connect the cable from the router's LAN port to the computer; Make sure the device is powered properly.

2. Check the instructions or instructions behind the router to confirm the network IP segment of the router, such as: or and the username and password (generally admin, the password may be admin or empty, see the router manual for details).

3. Turn on the desktop computer, confirm that the network is indirectly normal, right-click the desktop [Network Neighbor]--Properties]-[Local Connection]-[Properties]-[Interner Protocol]-[Properties]-[Use the following IP address]--Enter any IP in the IP segment of the router, for example: (or Word Network Mask; Default gateway or OK to exit.

How do you get online? In the case of ADSL, the ADSL password must be set in the router.

It's TP-link! Generally, you don't need to set it up. It's all automatic.

How to enter the settings interface:

Method 1:1: Check the router login information on the back of the router.

3. The router login interface pops up and enters the default login username of the router: admin and password: admin.

Method 2: 1, check the IP first, method: win+r--- enter: cmd--- enter in the black and white interface: ipconfig, press enter.

4. Pop up the router login interface and enter the default login username of the router: admin and password: admin (if it is incorrect, look at the back of the router).

First of all, you look at the username, password and network network management under your router, if yes, you can change the IP address to 254, choose any subnet) gateway and then open the management interface, enter the username and password.

Let the router and the computer be connected directly, it really can't restore the factory settings, there is a recessed place behind the router and press it for a while to reply to the settings.

Browser: Enter the username, admin password, and look at the back of the router.

Cause 1: The Winsock communication component of the system is faulty.

About 80% of the cases where you can't open a web page on QQ are due to the destruction of the Winsock component. There are several reasons why components are damaged: virus causes, sequelae of virus removal by perfect antivirus software, pirated Windows XP, faulty installation of operating system patches, and abnormal system restoration.

Cause 2: The domain name resolution error is incorrect.

Domain name resolution errors are also one of the common reasons why web pages can't be opened. When a computer resolves a domain name, it must first access the hosts file of the local machine, and then log in to the DNS (domain name resolution server) to query it.

Reason 3: Internet Explorer is corrupted.

If you can surf the Internet with QQ, you can open web pages with other browsers such as Firefox and opera, and only IE can't browse, then most likely the browser itself is damaged and you need to reinstall IE.

Reason 4: Incorrect settings.

Sometimes, setting up the wrong server can also cause the web page to not open. We can see the settings of the Synthetic Modification Server in the "Connections" settings under "Internet Options" in IE.

Reason 5: Virus problem.

There are not many cases where the web page cannot be accessed directly due to viruses, but some imperfectly written viruses and Trojans will be injected into the IE process, causing the user to open IE after the machine resources occupy 100, and the machine is in a state of suspended animation. In this case, upgrade your antivirus software to the latest version.

There may be a problem with routing, and there are many cases of routing.

Dear users, hello.

I hope the following can help you:

1.Plug the broadband modem or home network cable into the WLAN port of the router, and then connect to the computer through the network cable or wireless network.

3.After entering the page, you will be prompted to enter management, which also needs to be found in the manual, and the general password is admin.

4.Click the Setup Wizard, follow the prompts on the page to set up broadband without PPPOE dialing, and enter the broadband password.

5.According to the prompts on the page, check the box to turn on the WiFi network, and set the password, when finished, click Next, and the device will automatically restart.

Anhui Telecom will serve you wholeheartedly.

Hello, I have seen your question and am sorting out the answer, please wait for a while Hello, I have seen your question and am sorting out the answer, please wait for a while

How to set up a D-Link router?

The specific operation steps of the D-link router to set the password alarm are as follows: 1. First of all, we need to use a network cable to link the router with the computer, and we will insert the computer network cable into the LAN port of the router to connect the computer and the router. 2. Then we open the browser in the computer and enter enter in the address bar to confirm, and then we can open the address of the D-link router setting.

3. Enter the main interface of Settings**, we select dynamic IP for broadband access type in the settings interface, and select PPPoE if you need a broadband account password. 4. Then we set the wifi name and password on the liquid surface, and click the link on the right to set the password after setting.