Different issues with opening web pages after the router is set up

Updated on technology 2024-02-08
28 answers
  1. Anonymous users2024-02-05

    The first thing that can tell you is that there are no problems with your network and routing. The situation you mentioned is that the firewall trusts the software or accesses ** and automatically prohibits access because it does not trust the plug-in; The second is because you are connected to multiple computers and other computers are opening BT and other software** things or the network itself, resulting in the network speed is too slow (because of the advantage of bandwidth and response speed, it will be faster than others**, QQ because the data exchange with the host is different from IE, so it is not easy to find), if this is the case, you can enter the ping command in the command box to ping the local telecom host to judge, the more the value in the ms column in the beating data** the faster the clear network speed, The command format is ping the telecom host IP (for example, -l 1024 -t for Jiangxi; The third is that the data flow of the ** you are accessing itself is abnormal, resulting in a short-term failure or slow access.

  2. Anonymous users2024-02-04

    Feels like a DNS issue.

    In addition, some low-end routers have too little memory, which can also cause this problem.

    You can dial up the Internet without a router and take a look at the DNS address you get. Then connect the router and change your computer's DNS to the DNS address you saw just when dialing in to the Internet.

  3. Anonymous users2024-02-03

    Cause: The router is not connected to the Internet.

    Workaround: Set up router dialing.

    Computer enters the router]:

    1. The computer IP and DNS settings are automatically obtained.

    2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

    Set Router Dialing]:

    1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

    2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

  4. Anonymous users2024-02-02

    Log in directly to the interface of the router, select your Internet access method (dynamic IP or ADSL dialing), if you need to click on the broadband connection to access the Internet on a stand-alone computer, then select ADSL to dial, and fill in the broadband account and password [correct].

    Presumptuous: How do you access the Internet without a router at home? Do you want a broadband connection?

  5. Anonymous users2024-02-01

    It should be a problem with your router, it may be that some IPs are set up and you can't browse the web!

    Anyway, how did you come up with the expected settings interface? Prompted for your router's username and password?

  6. Anonymous users2024-01-31

    There are generally two common situations for automatic ejection router settings:

    Router Initialization Settings: Now many router settings tend to be more user-friendly, when you set up the router for the first time, open the browser will jump to the settings page by default, this function is very practical for more novice users. If this is the case, it is recommended to reset the router and generally solve the problem.

    Browser caching: Some browsers will cache the settings interface when the settings are inappropriate, so sometimes it may appear that the router has been set up and will jump to the settings interface. If this is the case, you can empty the browser cache, or you can clean it up with security software.

    Web authentication is set: Commercial routers generally provide web authentication or web notifications. If this is the case, it is usually possible to try disabling features such as web authentication.

  7. Anonymous users2024-01-30

    Instructions require the router to be set up.

  8. Anonymous users2024-01-29

    That's the problem with your router settings, you can log in to your router and reset it.

  9. Anonymous users2024-01-28

    I wonder how do you know if the route isn't broken?!

    Try it my way.

    First of all, you should set your computer to automatically acquire IP

    The computer is only connected to the route, and the route is only connected to the computerEliminate conflicts with other devices.

    Check the local connection status on your computer, and remember the DHCP server. You should type . in your browser addressDHCP server.

    If it doesn't work, you can basically say that the route is hanging.

  10. Anonymous users2024-01-27

    1. First of all, prepare the computer and a network cable, it is best to have the router manual, check and confirm the login IP of the router, the account number and password are very important, some TP link router login IP is, some are, it is also useful.

    2. Turn on the power of the router and the router is in working condition; Connect one end of the network cable to the computer and the other end to the LAN port of the router.

    Then the computer's IP:,Mask:,Gateway:

    Same as routers), and you're good to go. At this time, you can log in to the router, another way, if you are a laptop, you can access the Internet wirelessly through the router, you can also log in to the router directly; Enter : in the address bar of Internet Explorer, open the router page, and the general account and password are:

    admin。

    4. If it still can't be opened, it is possible that the login address has been artificially changed, and the factory settings can only be restored. Find the reset button on the router, press it for 5 seconds when the router is powered on, release it, and then restart it to restore it. If you can't do it with repeated resets, it's always possible.

    5. Enter the router settings interface, the menu is very intuitive, and you can use quick navigation to configure. If it is a unit network, there may be a static address, so you can fill in the corresponding address; If it is a telecom modem, you need to choose the pppoe mode, fill in the account and password of your telecom application, and the others can be defaulted; It is recommended to use automatic assignment of address for wireless network configuration, so that mobile phones and laptops can automatically obtain the address to surf the Internet, set a recognizable ID name, set the password for user authentication, and everything else is default, and others can be temporarily not set, and you are interested in slowly groping for it.

  11. Anonymous users2024-01-26

    Don't connect to the Internet, just connect the router to the computer, enter it in the address bar, and reset the router!

  12. Anonymous users2024-01-25

    Are you sure? There are some routers that have addresses that are not this address, such as TPLink W700N.

  13. Anonymous users2024-01-24

    It is recommended that you set a private IP address first, and then set up a router.

  14. Anonymous users2024-01-23

    There is a label on the backplane of the router with the IP address on it.

  15. Anonymous users2024-01-22

    Yours is wired or wireless.

  16. Anonymous users2024-01-21

    1. Recently, I often open the webpage to the wireless routing setting interface of other dormitories, and you can modify their routers?

    This is because you are logged into someone else's router and are using their wireless signal.

    2. If you use wireless, set up your own wireless router and connect wirelessly to your own SSID

  17. Anonymous users2024-01-20

    DNS issues. Just change the DNS of the router you can log in to manually specify as normal DNS. You can go to other computers where you can access the Internet normally to check your DNS address.

  18. Anonymous users2024-01-19

    If you can't open the web page, it may be that your school has Internet management software, so find the administrator who manages the network to understand.

  19. Anonymous users2024-01-18

    Your homepage is definitely set to or.

    QQ can be on the web page and cannot be opened, one possibility is that DNS is not set or the setting is wrong. Another possibility is that the school network restricts the use of routing.

  20. Anonymous users2024-01-17

    Always opening someone else's router page because you're logged into someone else's router.

  21. Anonymous users2024-01-16

    It is this route that interferes with your normal Internet access, if your route obtains the IP of this route, then you can't access the Internet, this is your LAN There are laymen using routes, in fact, he is also abnormal when surfing the Internet.

    To solve this problem, you can try to see if you can enter his route, if you can get in, then you turn off the DHCP of this route, so that you can access the Internet normally.

    If you can't enter the route, then you connect the network cable directly to the computer, get the IP and other parameters that can go to the Internet normally, copy it down, and then enter the setting interface of your own route, in the WAN port settings, select the static IP, fill in the parameters copied down, and save.

    Note that in this setting, the DHCP of your router needs to be enabled, and the network cable is connected to the WAN port.

  22. Anonymous users2024-01-15

    Ways to resolve router setup exceptions:

    Press (hold for 5 seconds) the router's reset button and wait until all the lights are on together for the reset to be successful.

    After the reset is successful, you will need to set up the router again (there is a wizard), because it has been restored to the factory defaults.

    Resources.

  23. Anonymous users2024-01-14

    The local LAN IP address has been hijacked by China Telecom, and you will definitely not be able to log in if you enter admin!

    The solution is very simple, you don't need to change the IP, reset the router first.

    Unplug the network cable of the uplink port (that is, the one that the cat comes over or the one where the cell broadband goes to the router), only keep the one connected to the router and the computer, and then turn on IE, enter it to log in to the router settings page.

    Since uplink is not connected,So this time after setting up and restarting the route, the computer can not access the Internet,All you have to do is turn off the computer,The power supply of the router and the computer is also cut off,Connect the network cable of the cat community broadband and connect it with the router,Then turn on the Internet access。

  24. Anonymous users2024-01-13

    The back of the router has a default username and password.

  25. Anonymous users2024-01-12

    I agree with Moden's point of view, it is a class C IP intranet address, and the switch assignment address of Telecom in your cell happens to be the first intranet switch, and you enter this address to log in to the interface of Telecom.

    So the solution to the problem is very simple, just disconnect from the telecom. It is to unplug the network cable of the telecommunications to your home. After that, enter the address and you will be able to log in to your router.

  26. Anonymous users2024-01-11

    That's because your router is not connected to the Internet, after you enter the router interface, look at the status of the WAN port, see if there is a number of IP address subnet masks, etc., if they are, then it proves that it is not connected, then you click on the link below, until the IP address appears after the number proves that it is connected, no, you are re-entering the account password in the connection.

  27. Anonymous users2024-01-10

    418697985 add me if it doesn't work.

  28. Anonymous users2024-01-09

    IE--Tools--Internet Options--Homepage--Set a homepage you want to set and enter a**.

Related questions
25 answers2024-02-08

You have restored the factory settings of the router, of course, you can't access the Internet, because the information in the router is also erased when you restore it. If you use win's built-in dial-up or Internet starry sky to surf the Internet, you can't connect to the router, directly to the cat. >>>More

17 answers2024-02-08

It's all the same, you take the optical fiber cat to borrow the WAN excuse to follow the line to the router on the computer to set up, and follow the wizard to enter the dial-up account password. If you have a question, thank you.

6 answers2024-02-08

This can be done via a wireless router.

9 answers2024-02-08

Looking at your screenshots, you probably want to limit other people's Internet speeds. >>>More

9 answers2024-02-08

Home Network Environment Cabling:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer. >>>More