The software was uninstalled during the one click restore wizard backup, and the system could not st

There are two scenarios in which the system cannot be started due to the landlord's situation:

1. If the MBR error is caused, you only need to rewrite the MBR

A. Enter DOS and enter fdisk MBR.

B. If you are not familiar with DOS, you can also enter PE, which has many tools that can rewrite MBR.

A. Put the WindowsXP installation disc into the optical drive.

b. Enter BIOS and set to boot from cd-rom

c. When it shows "Press Any Key to Boot from the CD", press any key.

D. When entering the Windows XP installation menu, press the "R" key to enter the recovery console.

e. Press the "1" key and press enter to log in to enter your Windows installation.

f. Enter your administrator account and password.

g. Copy two files to the partition where the system is located, assuming your optical drive is an F drive letter. Follow the example below:

copy f:\i386tldr c:\

copy f:\ c:\

When you're done, reboot it and you're good to go.

If you can't uninstall it, then brute-force it, delete the source folder of the restore wizard, and then delete the registry related to the restore wizard.

Go to the next brute-force deleted software on the Internet.

Try it or just in safe mode.

to uninstall.

I guess either you didn't unload it thoroughly. Either that one-click restore wizard is also in the registry.

You can use 360

Uninstall the software and take a look. Whether the unloading is complete. Then the garbage is cleaned up, and the plugin is cleaned up.

Finally use ccleaner

Clean up the next registry.

Freezing point of installation.

1. It can only be installed under win2000 and xp systems, and other systems are not supported.

2. Pay attention to the ...... of the hard disk to choose to protect when installing

3. After entering the system, the software calls out the hotkey.

ctrl+ait+shift+f6

You can also hold down shift and double-click the task icon to open it, and you can set a password after opening, and the default password is empty.

4. There are three options on the main interface:

1) The first one is the protection state, that is, the hard disk protected by each boot recovery.

2) The second is the free option, for example, the system is in the protected state, we choose the second option, the default is 1, this 1 refers to the unprotected state after the machine is restarted, when the machine is automatically transferred to the protection state after the second machine is restarted, then the operation we do after the restart will be automatically protected when the machine is restarted.

3) The third is not restored, after restarting, the freezing point chart will keep flashing red x, that is, all protected hard disks have been abandoned, at this time, run the freezing point installer to delete the freezing point.

2. Deletion of freezing point.

1. Press Ctrl+Ait+Shift+F6 to call out the interface, if you haven't changed it, the password is empty, and you can enter the software settings interface.

2. Select the third option, that is, give up the protection and restart the computer.

3. After restarting, the freezing point icon flashes red x, which means that freezing point has no protection of the hard disk.

4. Run the original program of Freezing Point, the delete option will appear, click Delete.

5. After restarting, Freezing Point will be safely deleted.

Recommendations:1Use the boot shutdown with disk management software such as diskgen to boot from the optical drive, re-pei Li to view the next partition, it is estimated that the power failure has damaged your hard disk partition, first use such as Nakano software to see if you can restore the original partition with slag, and then do the next step;

2.Suggestion 1: No, repartition the hard disk, if there is particularly important data, it is not recommended to operate, send it for repair; Generally important, you can repartition the system and use data recovery software to recover the data back!

3.There are other unexpected situations, such as power failure caused by other hardware failures, and if you solve other failures, try back and see Suggestion 1-2, which can solve the problem, which is great!

Have fun!

Provides 2 ways to uninstall:

1. Run the one-click restore wizard installer and select the "Uninstall wizard" option in the toolbox.

2. Press the F11 key when starting the computer to enter the one-click restore wizard, and select the "Uninstall the wizard" option in the advanced settings.

Note: Before uninstalling, it is recommended to go to Windows to check the error of the last partition and the penultimate partition (if the installation scheme 2 is used, the C partition should also be checked for error). For more information on how to find an error, see Question 1 of the Help Explanation Question.

Bottom unloading method.

Enter the DOS state and enter fdisk

MBR press enter, restart the computer.

Note that there is a space after the fdisk.

If it doesn't work, find someone who knows how to enter DOS, follow my method, and guarantee to solve it.

This method uninstalls without a password.

Please cherish! I don't know if you have formatted the C drive, if it is formatted, it should not appear above, if it is not formatted, it may appear, in this case, you first find the windows directory of the C drive, there should be one in it"One-click restore of the wizard"This directory,There's only one file in this.,It's to uninstall the file.,Just double-click it.,So uninstall and reinstall the wizard.,It's already backed up a system.,That's the last time you backed up.,If you want to install the backup, press f11 to go in and rebackup.,You can also do this.,Right click on my computer===Management===Storage--- Disk Management====Look at the right====You will find that in addition to your own cde....There are two disks (maybe only one) outside the disk (ibm-service), you can delete them, this is the system you backed up, now you know why you can restore the C drive after formatting.

It doesn't have to be F11 to restore the system screen. You have the option to launch and there may be that too. Check it out.

Open such as - Control Panel - Add and remove programs--- and then look for the restore wizard, if you still want to use the restore wizard, there is no need to uninstall.

Before you restore the sprite.

Just back up the system again.