What is the reason for the empty tripping after pushing up and tripping after a period of time?

There are many reasons why the air switch cannot be pushed up, and it may be that the air switch is damaged.

To see if the empty opening is faulty, damaged, whether it can continue to be used, or if it needs to be replaced.

If the inside of the air switch is damaged, simply replace it. If the trip is caused by a short circuit, it is necessary to find the point of the short circuit, and such a short circuit point can be determined by looking for the open wire such as the switch.

Power on for a period of time, touch the side of the empty open with your hand to see if it is overheated, and check whether the empty terminal is loose. Check the test of empty opening of graded loads or disconnecting lines one by one.

On this issue of projection ceiling sockets. The 3 wires are the live wire, the neutral wire and the ground wire, whether the socket you install is a three-eyed one, respectively.

It is generally recommended that water heaters, air conditioners, water dispensers and other large household appliances should take a separate line when taking the line, otherwise it will be particularly easy to trip when using it in life.

Notes:

If there is a short circuit in the load line, it will generally trip at the moment of start-up, or it will not be able to send power at all at the moment when it is turned on empty. Or maybe there is a problem with the empty opening.

The electrical appliances in the home are overloaded, or there is a short circuit in the electrical appliances in the home. Try unplugging the high-power appliances in your home first, and then pushing the gate up. Eliminate which appliance is the cause one by one.

When an air switch trips and pushes it up and then jumps down after a while, it may be due to one of the following reasons:

Overload: A load connected in the circuit exceeds the rated load capacity of the air switch. This could be due to an excessive load or a faulty wheel ride in one of the electrical equipment, causing the current to exceed the carrying capacity of the air switch. The solution is to reduce the load or repair the faulty equipment.

Short circuit: There is a short circuit in the circuit, resulting in an abnormal increase in current. Short circuits may be caused by short circuits between wires or faults inside electrical equipment.

In the event of a short circuit, the air switch trips to prevent excessive current from damaging the circuit. Short circuits need to be checked and repaired.

Ground leakage current: A leakage condition occurs in an electrical device or wire, causing current to pass through ground instead of a normal circuit. The floor leakage current will trigger the air switch to trip. It is necessary to check the insulation of equipment or wires and fix leakage problems.

Cause of air switch tripping:

1. The load line of the air switch is short-circuited to the ground.

2. The air switch is damaged.

3. If the air switch is too small, it will lead to tripping in the case of overload.

Solution: 1. Carefully check the line insulation on the load side of the air opening, and if necessary, you can use the multimeter resistance file to measure the lead line insulation.

2. Check the air switch and replace the new air in time.

Due to the heavy load of household appliances, exceeding the rated load belongs to overload protection tripping, because some electrical appliances are grounded, tripping due to leakage protection, you can gradually plug in or turn on the appliances.

When you turn on an appliance and it trips, you must first check the appliance for suspicion of leakage, or a high-power appliance. The load accumulates to exceed the rated load, check whether there is leakage and all other electrical appliances can be turned off or unplugged, open this piece separately, if it is opened normally, it means that it does not leak, if it will also trip, it means that the problem is on this equipment.

Precautions for air opening.

Leakage protection switch.

The target is the line of fire. Because when a person comes into contact with a fire wire, the human body will form a circuit with the ground, and the current will not pass through the neutral line. At this time, your battery unit will be triggered immediately, and the power will be cut off to protect the human body.

Now there is also a fusion air switch.

and leakage protection switches for new leakage protection switches. It is triggered on the basis that the current flowing into and out of the circuit must be equal, and if it is not equal, it will be judged to be leakage, and there will be a jump turn.

Summary. Hello, there are several reasons for empty tripping: leakage tripping, short circuit tripping, overload tripping, and wiring error.

Hello, there are several reasons for empty tripping: leakage tripping, short circuit tripping, overload tripping, and wiring error.

If the air is broken, it will also trip, and it will heat up for a long time, and if it heats up, it will overload the current and trip, so this should be replaced with an empty one.

New empty opening. If you don't know the reason, you need to unplug all the electrical appliances in the house to see if there is still a sign of tripping, if not, and then test which electrical appliance is trapped one by one.

Unplug it or jump it after a while.

Have you tried which appliance caused it?

The environment where the electrical appliances are used is relatively humid, and the moisture is relatively large at the place where the lamp head is connected to the wax head, the socket joint, the internal control switch joint, and the slippery part of the leakage switch joint, which produces leakage current, resulting in the phenomenon of jumping Chang Que Gate over the action current of the leakage switch.

Air switch. After pushing it up, it tripped after a while.

There are several reasons for this:

1.Leakage, if the leakage current is large, it will trip;

2.The wire is thin, causing the wire to heat up.

causing tripping; 3.The switch is small, replace the big switch;

4.The switch is aging and the switch is replaced.

The specific reason is to find a professional electrician for maintenance treatment.

The air switch trips every few days, 1. The air switch always trips, generally because of the short circuit, in the case of short circuit, it will trip frequently, but when the short circuit occurs, because the current is relatively large, the voltage will be very small, and the problem of tripping will occur. It is necessary to ask a professional electrician to come to the door to repair it to avoid danger. 2. Always tripping, there may be a short circuit in the electrical appliance, which itself is faulty, so at this time the current will increase, which will lead to a short circuit tripping.

Or because the circuit is overloaded, exceeding its safe current range, then the air switch will cause tripping in order to protect the circuit. 3. There is also a possibility that the power of the selected air switch is relatively small, which is not consistent with the high-power electrical appliances, and exceeds the rated power, which will lead to tripping. Hope it helps.

1. It may be due to excessive load. 2. There is a problem with the line, and the line is grounded or the line is meeting. 3. There is a problem with the household appliances used at home.

4. It is also possible that there is overcurrent in the line, or the screw of the crimping line is loose. Suggested solutions: 1. If it is tripped due to excessive load, then it is necessary to replace the air opening with a larger load to solve this problem.

2. If there is a problem with the line, then you need to contact a professional maintenance personnel to overhaul it, and it is not recommended to solve the line problem by yourself, and it is very likely that you will be electrocuted by yourself, so you must pay attention. 3. If there is a problem with household appliances, then it is necessary to check one by one, and if there is a problem with a certain electrical appliance, then it is necessary to contact professional personnel to repair the electrical appliances. 4. Open the empty open to see if the screw is loose, if the screw is loose, then you need to cut off the total power supply, and then tighten the loose screw, you can solve the problem of tripping after a period of time.