If you want to install a ceiling lamp in the room, there is no wire, how to deal with it?

You can ask a professional decorator to solve this problem for yourself, and there is a very simple or easy way to hang it up. And it looks particularly aesthetically pleasing.

You can take the bright line, this way is a little unsightly, but it still has a certain effect.

You can open a slot to lead the line to this side, and basically it will not affect the installation of ceiling lights, so don't worry too much.

At this time, you can groove the room, if you don't understand it very well, you should go to a professional at this time, and let the professional person come to the door to get this done.

1 Buy a crystal lamp or 100 ceiling lamp, if you want to try the light is not bright, if there is a packaging film must be torn off, otherwise it is beautiful, especially the crystal lamp, stainless steel lamp board has a layer of white film cover and needs to be torn off to reveal a brand new light.

2 Then there is an I-shaped lamp head, turn the screw rod of the I-type lamp head and the lamp head of the lamp head to the right, and then tighten and fix the screws. In the next step, the I-frame should be fixed to the roof. The distance cannot be adjusted after the screw is fixed, so the screw should be fixed first.

3. Then in a mild position on the roof, the award of the I-shaped or cross-shaped frame is placed in the version of the accurate (can not be bent), with the stroke point, it is better to draw a few points to prevent the hole from touching the reinforcement, you can change a place to play.

4 After punching the hole, fix the expansion screw in the hole position of the I-shaped or cross-shaped frame, knock the expansion screw into the hole with the right eye, and tighten the screw with pliers or wrench.

5 After tightening the screws, hang the light board on the adjusted screw rod first.

6 Chandelier accessories, such as pendants, crystal bars, etc.

7. The glass plate decorated under the upper lamp should be fixed and adjusted to a horizontal height.

8. Finish, as shown below.

If you want to save trouble, buy white parallel wires and fix them with clips. Then use a plastic gusset to plug the wire inside the gusset. Then there is the painstaking task of cutting a trench in the ceiling with a toothless saw, putting the line in, and smoothing it with plaster.

If the wire is broken by you, the wire will be scrapped, and another line will be laid.

Method: Pull the broken wire out of the protective tube, replace one or two new wires (break a few and replace a few) into the protective pipe.

The easiest way is to pull out all the threads, see how many are broken, replace a few, and then thread them into the protective tube together.

Note: When some decorations, the pipelines are not laid according to the regulations, and these wires cannot be extracted, and they become disposable, so they can only scrap the broken wires and then lay open wires.

I don't know if your thread can be drawn.

Ceiling lamp is a kind of lamp, as the name suggests, because the top of the lamp is flat, and the bottom is completely attached to the roof when installed, so it is called a ceiling lamp. The light sources include ordinary white bulbs, fluorescent lamps, high-intensity gas discharge lamps, tungsten halogen lamps, LEDs, etc. At present, the most popular ceiling lamp on the market is LED ceiling lamp, which is often used in various places such as homes, offices, and entertainment venues.

Yes, but it's not pretty, so decorate it.

1.The electrical contact between the two terminals connected to the power supply of the ceiling lamp should be good, wrapped with vinyl cloth respectively, and kept at a certain distance. If possible, try not to put both terminals under the same metal sheet to avoid a short circuit and danger.

The phase wire should be connected to the terminal of the center contact, and the neutral wire should be connected to the screw terminal; When replacing the bulb, the insulated housing of the lampholder should not be damaged or leaking to prevent electric shock. When installing ceiling lamps in masonry structures, they should be secured with embedded bolts or with expansion bolts, nylon plugs or plastic plugs. Do not use wooden wedges.

And the bearing capacity of the above-mentioned fixings should match the weight of the ceiling lamp. This ensures that the ceiling lamp is fixed firmly and reliably, extending its service life.

2.When using expansion bolts for fixation, the bolt specifications should be selected according to the technical requirements of the product, and the drilling diameter and embedding depth should be consistent with the bolt specifications. Drill holes in the roof of the shed with the chassis.

Drill holes and lower the expanded rubber stopper. Thread the wires through the chassis and secure the chassis with screws. Wiring.

Install tubes and shades. After the lamp is installed, the power is turned on and the light test is turned on. Ceiling lamps cannot be mounted directly on combustible objects.

Some homes use painted plywood to decorate the back of ceiling lamps for added aesthetics. In fact, this is very dangerous, and it is necessary to do a good job of thermal insulation.

3.If the surface of the luminaire is flammable at high temperatures, thermal insulation or heat dissipation measures should also be taken. Ceiling lamps with incandescent bulbs, the bulb should not be near the lampshade; The power of the bulb should also be selected according to the technical requirements of the product, not too high, so as not to cause the temperature of the bulb to be too high, and the glass cover will fall down and hurt people after it is broken.

The electrical contact between the two terminals connected to the power supply of the ceiling lamp should be good, wrapped with vinyl cloth respectively, and kept at a certain distance. If possible, try not to put both terminals under the same metal sheet to avoid a short circuit and danger.

4.Ceiling lights are used very frequently. Therefore, when buying ceiling lamps, it is recommended to choose big brand merchants to cooperate and ask for invoices from merchants as much as possible.

If there is a problem, it can be repaired or replaced. Ceiling lights are used very frequently. Therefore, when buying ceiling lamps, it is recommended to choose big brand merchants to cooperate and ask for invoices from merchants as much as possible.

If there is a problem, it can be repaired or replaced. Special attention should be paid to the power cord of the ceiling lamp, the cross-sectional area of the wire must be greater than mm, because the lamp is live, and the fingers should not touch the metal lamp head during installation, so as to avoid the risk of electric shock.

When installing, you should determine the location of the installation, generally in the living room for installation, and you also need to close the electric switch, and then install the base reserved wire hole, you need to pay attention, can not be screwed very tightly, pay attention to cut off the power supply, pay attention not to destroy the lamp, and should also tighten the screws.

When installing, we must choose the right lamps, and then we should also pay attention to the selection of size and specifications, and at the same time, we should also pay attention to the location of the installation, and try to choose a professional decoration master for installation. When installing, pay attention to the connection between the live wire and the neutral wire, and try to choose the dark wire.

When installing, it can be installed on the ceiling in the room, and it is also necessary to pay attention to the connection of the line during installation, pay attention to close the electric switch in advance for installation, pay attention to the installation compactly, there can be no gaps, and pay attention to the overall color.

The bottom box of the ceiling lamp, which is the part where we reserve the power supply. This part is generally on the top plate, and the bottom box of the installed lamp is buried inside. After the renovation of the electrical circuit in our house is completed, the wires must be threaded to this position.

There are generally two wires in the ordinary bottom box to meet our ceiling lamp installation, which is one of the most basic conditions for the installation of ceiling lamp, which is power supply. How to install ceiling lights? I learned 5 installation steps to install the ceiling light base by myself.

In other words, after we buy the ceiling lamp, we can separate. One of the most important components is the base of the ceiling lamp.

The base of a ceiling lamp is usually made of metal or other material, and the other part is the light source of the lamp inside. We can all quickly get rid of this part in its entirety. And we will find that there are screw holes in the floor of the ceiling lamp, which are used when installing with our ceiling or bottom box.

The other part of the ceiling lamp is the lampshade of the ceiling lamp. Because ceiling lights, no matter what bulb is used, such as energy-saving bulbs or LED beads, are installed on the floor. Later, you need to cover these bulbs with a lampshade to show good results.

Therefore, the shade of the ceiling lamp is removable.

Once you have all the installation tools ready, first choose a good installation location, such as in the living room and kitchen, preferably in the middle, so that the light can shine more evenly and brightly. If you're in the bedroom, try not to be above the bed, as this will affect your sleep. At the same time, in order to avoid the consequences of falling from the installation, try to choose a place with high bearing capacity such as masonry.

Remove the ceiling lamp mask. In general, the mask can be fixed in two ways: rotating and breaking.

When removing the mask, the lamp can be removed at the same time. Pay attention to the process and be careful not to break the light.

Install the base and pre-pass the wire hole in the base at the reserved place. When screwing in, be careful not to tighten too tightly so that the position can be moved during future inspections. Once the base is secured, attach the power cord to the lamp holder.

At this time, cut off the power supply to avoid the risk of electric shock. At the same time, wrap the thread with a black belt in advance and keep it at a reasonable distance. Once all the wiring is complete and all the electricity is turned on normally, the mask and pendant can be installed.

What needs to be paid attention to when installing ceiling lamps must be turned off before installation, so as to avoid safety accidents such as electric shock during installation. The place where the luminaires are installed must be sturdy and durable, avoiding wooden and flammable places. Ensure the integrity and safety of the lamp.

When replacing the bulb, the holder housing must not be broken to prevent electric shock.

First of all, the position of the installation light should be cleaned, and then the top light can be glued to this position.

The installation is relatively simple, first of all, turn off the power, and then take out the ceiling lamp and put it in the position to be installed, you can also use a pencil to mark the position of the base, and then according to the installation hole, put the ceiling lamp on the ceiling to drill holes.

Install on the ceiling and make a few screws on the ceiling so that you can put the ceiling light on it.

You should ask the appropriate professionals to carry out the installation, the most important thing is that if you install it blindly, it is likely to have a certain impact on the roof, so avoid this situation.

You can install a ceiling lamp with an open pipe and open wire, and install a small section of wire under the lamp called the ceiling lamp holder to press.

1. All 1, the first choice is to solve how to fix the lampshade or ballast lamp, first investigate to see if the screw holes on the original lampshade fixed and the ceiling can be reused, if not, additional drilling is required; The tool needed is a percussion drill cross (slotted) lot, which is used to drill holes in the ceiling.

2. Before installation, make sure that the power switch of the ceiling lamp is turned off (if you can't confirm it, please turn off the main power switch for entering the home).

3. The ceiling lamp is AC power supply, and the live wire and zero line are connected to the live wire and zero line from the wall respectively according to the live wire and zero line on the ballast (if you can't distinguish it, you can connect it casually and there is no defense).

Fix the base first, then install the lampshade. There should be installation instructions, if not, you have to ask the person who sells the lamp to install it or go to a local electrician to install it.