Where can I buy table tennis rubber? How to paste to get the best effect

There are all in the table tennis equipment store, the rubber is not necessarily the best, it depends on your playing style, you can stick some rubber if you like to pull the ball, and the elasticity of the rubber, such as Hurricane 3, and Tianji 3 are good, that is"Control + Speed"The performance - delicate and fast continuous pull ball, **on more than 100 sides, different places**! The level is not too fine may not be adaptable, so you have to buy the right one for yourself, the level is in the amateur in general, it is more appropriate to buy the 729 series, ** is not very expensive, dozens of dollars on one side, when you feel that the elasticity of pulling the ball is insufficient, you are considering changing a better rubber!

Good luck!

Go, stationery store, tear off your piece of garbage, and then brush the glue (to be special) on the newly bought rubber, and then align the racket, and cut it off with a knife along the side, I hope mine will help you.

There are many things on the Internet, amateur players don't have to worry about pasting, even if they use the national team's sticking method, it will not reflect any effect in amateur hands, but it will be troublesome. Thankless work, no need to do.

Generally, it is sold in gymnasiums, using inorganic glue.

They are available in sports equipment stores.

In fact, if it's fair, the service is good, I think Bauhinia Ping Pong is very good, I've been there before, I'm very careful, and the recommended film feels like it's suitable for you. . . Good luck!

Saiv is sold on the Internet, and you can help stick it for free.

<>1. Prepare sponges, single rubber sheets, sponge blocks (for brushing inorganic glue), and glue sticks in the key slide.

2. Squeeze a little inorganic glue (about the size of a dollar coin) onto the rubber.

3. Brush evenly along a straight line with a sponge block.

4. Wait for the glue to dry. When the inorganic glue dries, it will be transparent and let it swim.

5. The sponge end is also coated with inorganic glue in the same way, and wait for it to dry.

6. In order to avoid mis-adhesion, cover a piece of plastic film (or white paper) on the rubber sheet, leaving only one bottom edge for alignment.

7. Align the bottom edge of the draft mountain with the sponge, and then pull out the plastic film.

8. Use a rubber rod to evenly paste the rubber and sponge together.

9. Then you can get a beautiful, flat and bubble-free assembly rubber with strong performance.

1. First of all, we will put the things we are going to use in front of us, the position that we can reach, table tennis rackets, two new pieces of rubber, special glue for table tennis, knives, rags, etc.

2. In order to save time, we can first brush one of the two new pieces of rubber with glue. Pay attention to be even when brushing. Wait until it is dry before brushing, a total of 2 or 3 times.

3. Next, we will tear off the old rubber on the table tennis racket, there will be a sponge under the rubber, which is more difficult to clean, we can use a knife to cut off along the edge, and use a knife to cut off the residue after tearing it off. After getting the forehand right, tear the rubber of the backhand.

4. Brush the wooden board with special glue for table tennis, brush it evenly, brush it again after drying, and balance filial piety 2 or 3 times. When brushing the glue, find that the remaining sponge is cleaned up in time, so as not to stick to the new rubber will be uneven and affect the use.

5. When waiting for the rubber and planks to dry, we can clean up the sponge debris to the point, and there is no debris for easy operation.

6. After the rubber and board are brushed 2 or 3 times and the glue is dry, I brush the board and the new rubber again, and press it once along the outer edge with my thumb. If there are some parts that can't be sticky when sticky, you can press it on it at noon, such as a water cup.

7. After that, glue another piece of rubber.

8. Because after brushing the glue many times, the rubber will swell, after the two new pieces of rubber are glued, we have to use scissors to cut along the outer edge, and try to carefully guide the manuscript when cutting, otherwise it will affect the appearance.

9. Finally, we wipe the rubber with a rag and remove the ash. Then put it in the case of the table tennis racket and you're done.