If there is a leak at the door of the bathroom, it can be determined that the washbasin is leaking,

When the new building is delivered, the bathroom is generally waterproofed, but most of the people will pave the floor tiles, level the ground, and rearrange the water and water pipelines, which will destroy the original waterproof layer of the bathroom, so the waterproof layer of the bathroom must be redone when redecorated. First, the ground is leveled with cement mortar, and then waterproofed, the ground is cleaned first, and the polyurethane water glass waterproof coating is repeatedly brushed all over. The joints between the wall and the ground and the joints of the pipes between the water and the water are the most likely places to leak, and the workers must be urged to deal with these edges and corners, and the waterproof coating must be applied in place.

The decoration team is required to do cement mulch for the upper and lower water pipes of the kitchen and bathroom, brush the polyurethane waterproof paint from the ground up to the centimeter, and then redo the polyurethane waterproof on the ground to enhance the waterproofness. "Leakage test" to test waterproofing after the completion of the waterproof project, seal the door and the drain, fill the bathroom floor with water to reach a certain liquid level height, and make a mark, if the liquid level does not drop significantly within the hour, especially the roof of the downstairs house does not leak, the waterproof will be qualified. If the acceptance is unqualified, the waterproof project must be redone as a whole and then re-inspected.

Don't ignore this link, many road decoration teams don't do waterproofing at all, they are all finished with glass glue, so that once the water leaks afterwards, it will be too late to remedy, so the waterproof experiment must be done. After confirming that there are no leaks, the floor tiles are laid. There is often water in the bathroom, and it is easy to slip when walking on it, so it is best to use non-slip floor tiles with raised patterns, which not only have good waterproof properties, but also are not too slippery even in the case of water.

At the same time, the ground should be slightly inclined to the floor drain to facilitate flushing and cleaning. The materials used and the walls and floors of the bathroom should be protected from moisture, erosion and mildew.

Most of the leaks in the bathroom cabinet are these two places, one is the locking place of the drainer of the basin for a long time, the rubber mat has been aging, you can tighten it first to see if it is OK, if not, change the drainer. The second place is the angle valve and hose, which is rusty and aging and leaking for a long time, and you can check whether it is the angle valve or the hose is aging and broken. You can change it yourself.

You can determine whether the washbasin is leaking, and then see if it is an open pipe leak or a dark pipe leak. If the pipe leakage is easy to deal with, it should be replaced, and it should be repaired. If it is a hidden pipe leakage, it is best to ask a professional person to deal with it to avoid expanding the scope of the leakage.

Check whether the washbasin sewer pipe is blocked, or the pipe is broken, and repair and dredge.

In this case, it is recommended to replace the broken washbasin, prepare tools to close the sluice, replace it with a new one, and install it on it, it is generally relatively simple to change, if you really can't change it, you can spend money to hire a plumber to replace it, and it is not expensive.

Leakage under the washbasin, first look at the washbasin drain hose can be damaged, the basin drainer is tightened, there are sealing rings up and down, and whether the washbasin hot and cold water triangle valve is leaking.

First of all, it is necessary to determine what the cause of water leakage is, one is the leakage caused by the broken pipe, and the other is the leakage caused by the damage of the waterproof layer and the moisture on the ground.

1. Broken pipes.

Judgment: According to the construction drawings to see the direction of the water pipe, if the leakage part is buried with a water pipe, turn off the sluice gate and dry the faucet, if the water on the wall is dry after a period of time, it means that it is a problem with the water pipe.

Solution: Pry the tile open, check whether the water pipe or interface is leaking, replace the damaged water pipe or interface, bury the water pipe after the replacement, and do all the waterproof within the scope of the reconstruction, and then paste the tile.

Second, the waterproof coating is damaged.

Judgment: There is a leakage on the back surface of the bathroom, and the leakage of the wall has improved after a period of time, which can be inferred to be the problem of the waterproof layer.

Solution: Knock off the surface tiles, first find that there is no gap between the floor tiles, you can use Niu Yuan waterproof water to plug the leakage and smooth, and then brush the waterproof paint on the wall.

If the water leaks due to the previous waterproofing height not being high enough, re-plane the tiles at the heights, waterproof the walls at the heights, and then apply the tiles.

The waterproof layer is leaking. Use a three-piece set of water leakage repair products in the bathroom of 100 million homes. Set ** online to find 100 million waterproof. Work something out.

The waterproofing of the bathroom floor has not been done, or the waterproof layer has been damaged; Or the floor drain is not tightly sealed, causing the problem of water leakage. To solve this problem, the only way to do it is to redo the waterproofing.

There could be two scenarios.

1. The house was not waterproofed when it was decorated.

2. The waterproof layer has been destroyed, but the more tired the day is, the waterproof layer has been destroyed.

In this case, you must redo the waterproofing to measure the bottom.

1. Knock off the tiles.

2. Find a waterproof master to do waterproofing.

3. Closed water test for 24 hours.

4. No leakage can be tiled.

If you take a bath on the wall often, the waterproof will be high) and you will not take a bath often to achieve 50 cm.

Do waterproofing: Check the water pipes.

Is it a leaking pipe or a cloudy water on the ground.

1. Treat the dust, oil, and stagnant water on the surface, and keep the surface dry;

2. On the entire surface that can be drenched with water, such as: tile surface, tile joint, wall joint, pipe root and other parts, spray and brush penetrating waterproofing agent, and do not leak spray;

3. After the surface of the waterproofing agent is dry, fill all tile joints, damaged and defective parts with waterproof paste;

4. Weak links such as wall corners, wall edges, and pipe roots are reinforced with plastic steel mud.

How to deal with the leakage of the bathroom downstairs 1. If there is a leak in the hidden pipe in the wall or floor of the bathroom, it is necessary to check from the place where the leakage is more serious, find the damaged pipe, and replace the new pipe in time.

2. If the waterproof layer of the bathroom is damaged, causing the bathroom to leak downstairs, then the bathroom must be waterproof with five layers when repairing the waterproofing. However, special attention should be paid to the fact that the waterproof material must choose a large brand of high-quality materials, and also ask the relevant maintenance personnel to deal with it. so as not to bring more trouble.

What are the waterproof skills of the bathroom 1, the interior decoration of the bathroom must be waterproof, and the wall must be waterproof before the wall is buried. In general, the waterproof height of the wall is set at 30 cm, but many families are currently equipped with shower rooms in the bathroom. So the waterproof height of the whole wall should be meters.

If it is a light wall, the entire wall needs to be waterproofed.

2. When the bathroom is waterproofed, the joints between the wall and the ground, and the joints between the upper and lower water pipes are also particularly prone to water leakage, so the construction personnel must be reminded to do a good job of waterproofing in these areas during construction.

3. When the bathroom is being renovated, the floor tiles must be waterproofed. Before replacing the new floor tiles, it is necessary to remove the original tiles, use cement mortar to smooth the entire floor, and then start to do the waterproof layer treatment, so as to avoid water leakage caused by uneven thickness of the waterproof coating.

4. When the bathroom is decorated, the original waterproof layer can not be damaged, and the house will generally make a waterproof layer on the ground when handing over the house, and the waterproof material is thinner, so the original waterproof layer of the ground must not be damaged.

Leaking water next to the toilet flush is a very common problem. Normally, this kind of water leakage will not have much impact on other facilities in the restroom, but if the leakage is too large, it will cause irreversible damage to the floor. Therefore, it is very important to deal with the leak next to the toilet in a timely manner.

Here are some common ways to do this:

1.Check the tank and sprinklers: The first thing you need to do is check the tanks and sprinklers for cracks or corrosion. If these problems arise, the tank or sprinkler head needs to be replaced.

2.Adjust the water level of the tank: In some cases, leaks around the toilet are caused by the water level of the tank being too high or too low.

The water level of the tank can be adjusted so that it is just aligned with the sprinkler head and does not exceed the location of the overflow outlet. This avoids situations where the water flows too much or too little, thus avoiding water leakage.

3.Replace the seal: A leak next to the toilet can be caused by a damaged seal.

If it is confirmed that the seal is damaged, it needs to be replaced with a new seal immediately. Generally speaking, seals can be purchased at a nearby hardware store, and it is recommended to consult a professional before replacing them.

4.Check the nuts and screws: Water leaks around the toilet bowl can also be caused by loose nuts and screws. When dealing with water leaks, care needs to be taken to check that the relevant nuts and screws are tightened. If it is loose, it needs to be tightened with a wrench or screwdriver.

In short, dealing with a leak next to the toilet requires patience and care, first you need to confirm the cause of the leak, and then take the corresponding treatment method. If you can't solve it yourself, you can seek professional help to avoid more losses caused by misoperation.

The causes of the water leak could be:

1.It may be due to the fact that the downspout and washbasin are not properly sealed.

2.It may be that the size of the downspout is relatively different from the drain of the washbasin.

3.It may be that the downspout itself is a quality problem, and the sealing is incomplete.

The workarounds are as follows:

1.The most straightforward is the complete replacement of the washbasin and downspout.

2.For self-maintenance, you can use waterproof glass glue or hot melt adhesive, pay attention to keep it dry and the connection clean and free of foreign objects.

3.After the second step of the solution, if there is still a leak, it may be a quality problem of the downspout itself, and the downspout must be replaced.

During installation, you can put some glass glue on the thread part, your situation may be poor drainage, the sealing ring below and the washbasin sealing effect is not good, it is recommended to change one.

Generally, this position is made of glass glue, loosen your drain pipe, wipe it clean, smear a circle of glass glue and then tighten the lock nut.

This does not need to be made of glass glue, mainly because the rubber pad is not done well, and the glass glue only plays an auxiliary role; It is advisable to buy a better drainer;

If you change one and buy it at a grocery store, it will be about 15 yuan.

Buying a new set of washbasin drain accessories will solve the problem, the one you marked as tight as possible, you can install it yourself.

Hope it helps.