How can I make the water drain faster in the restroom floor? What s the solution?

Be sure to pay attention to the use interval during the watering process, as this will make full use of the heat of the hot water to thaw the frozen pipes without reducing the life of the sewer pipes. In addition, all alkaline substances (basic oxides + alkaline hydroxides) + active metals (metals reflected with water: sodium-potassium-calcium-barium) + concentrated sulfuric acid - concentrated nitric acid + nitrogen dioxide - sulfur trioxide - phosphorus pentoxide - phosphorus trioxide will encounter water after heating.

It is possible to generate heat in this way and then dredge it, but only if you know what the sewer pipe is and find out the alkaline substances that will not react with it before you can use this method. In the cold winter, turn on the faucet a little at night to let the small flow of water continue to flow, which can achieve a good anti-freezing effect and can effectively prevent the water pipe from freezing.

<>Of course, the amount of water should not be too large, otherwise it will be a waste of water. If the frozen part of the pipe is long, or even inaccessible underground, it can only be handled by the maintenance personnel of the property department. Generally, they will have a good thawing method, and after the pipeline is dredged, they will also take reasonable and effective anti-freezing and thermal insulation measures to prevent the water pipe from freezing here.

Clever setup. When we decorate the bathroom, the ground of the bathroom must have a slope, but this slope, do not let others see that it is a slope, in its lower part near the 1 point of the floor drain, the drainage is not high so that the bathroom is flooded, and there must be a correct choice when choosing its floor drain, you can choose the floor drain well, or you can make the drainage poor.

There is a sink on the ground. Now the decoration is particularly novel, a sink in the bathroom, it can form a convex groove in the middle on both sides, so that the position of the floor drain is in the groove, so that it will naturally lead out of the groove, for such a design the drainage speed is much faster than the tile, and its water will not appear, now renting a house is such a design. Drain on all sides.

There are two ways to make a toilet drainage design on all sides, one is to make a groove on the marble, Dali ordered to let the workers make a groove after the water is cut off around, and there is to use tiles in the middle to leave the bedding around him, free design is the best effect that can bring the water out. The design of the surrounding water allows the water to flow faster, and will not affect our lives due to the stagnant water environment, so our home will not be wet.

Effective wet and dry separation will definitely drain better than a bathroom without wet and dry separation.

When doing dry and wet separation, in addition to making a partition in the longitudinal space, it is also necessary to pay attention to the use of water retaining strips on the ground - water retaining strips, which can prevent water from running around on the ground.

The floor of the bathroom must be level, and the flatter the better. First of all, when laying floor tiles, you have to find professional workers, I have seen the owner of his own construction, the ground is potholes, and it is called a strange thing if there is no water accumulation. The greater the slope of the ground, the faster the water flows to the floor drain, and the faster it can be discharged.

The slope of the ground is 2% to 3% commonly, and the maximum may be 5%. If the slope is too large, it will affect the normal standing of people on the ground (there will be a significant sense of inclination when standing on the ground) - if there are elderly people and children, it is easy to be dangerous.

At this time, you should pay attention to the slope design of the bathroom, you can choose a centimeter of slope, to determine the direction of the sewer in advance, to choose the best floor drain, you can make a groove in the bathroom room, in the early stage of decoration should pay attention to the laying of water and electricity pipelines, to ensure the smooth flow of the sewer.

The ground can be planned to ensure the leveling of the ground. You can bury some pipes next to it, you can also increase the slope of the bathroom, adjust the slope, you can also adjust the pipes of the bathroom, and you can also open some slots.

The floor of the restroom can be tilted, and some ditches can be set up so that rapid drainage can be achieved. The slope of the toilet can be increased, some channels can be set up, the area of the drain can also be expanded, and some drainage grooves can be set up.

Nowadays, most of the toilets are sunken before handing over the house. Therefore, before paving the ground tiles, the construction of the ground waterproofing project is carried out first, and then the corresponding raw materials need to be backfilled(Some use carbon slag, but also effective other materials to make backfill), and deal with the flatness of the foundation cushion. Selection of wall tiles.

The wall tiles of the bathroom must be selected with good quality, and the surface should be leveled, and there is no edge, seven arches and eight warped arches. At the same time, the water absorption capacity of the glaze layer should be tested.

The key link is to have a dedicated and conscientious construction management personnel and operators, which is also very important to maintain the flatness of the toilet. The flatness of the bathroom is not the flatness of ability, but there must be an inclination, that is, the inclination of adding water. Only with the inclination of the water can the water inside be quickly drained and kept clean.

Therefore, the on-site operation staff of brick laying, on the basis of the foundation cushion, need to do a good job of adding water before laying bricks, and then begin to maintain the end of the project construction according to this inclination. The inclination of the bathroom floor tiles is all mastered by experienced masters, <>

Generally, the pavement should be 1% and 3% of the slope slope to prevent odor floor drain (the lowest place); The pavement of the toilet should be no less than 3 cm lower than the indoor floor. The tilt will affect the assembly of sanitary ware such as toilets, and the tilt will not be effective for the drainage pipe. The most essential factor of water storage in the shower room is that the ground is uneven and its water can not be released, because the water flows to a low place, so the drainage hole or the area of the anti-odor floor drain must be if the lowest place in the shower room, the area that avoids the odor-proof floor drain can be slightly higher, and then the floor drain of the drainage pipe is reduced to its relative height, so that the water can be easily discharged from the field, and it is not easy to lead to the situation of water storage.

If the road surface is particularly uneven, and the distance between the odor-proof floor drain is also very far away, you can consider finding a minimum value in this uneven area and installing an odor-proof floor drain, so that the water can be discharged as soon as possible, and it is not easy to cause water seepage. You can draw a small groove on the floor tile, make the depth of this groove a little lower, and lead the water to a low direction, so that the stored water can be discharged to the odor-proof floor drain according to the drainage method of this groove.

I think it's best not to do this, because most bathrooms will do some slopes in the process of renovation, so that they are also for better drainage, and these slopes are not felt in our daily life, it is just a slight slope, which will not affect our normal life.

In the process of bathroom decoration, the floor level and drainage of the bathroom are very critical, and only by doing these two things can the bathroom be used better.

Fault treatment can be carried out, and now the vast majority of bathrooms are sunken before delivery. Therefore, before laying the floor tiles, the waterproof layer construction should be carried out first, and then the corresponding materials should be used to backfill (some use carbon slag, and some use other materials as backfills) to deal with the flatness of the cushion. By doing so, the bathroom floor will be flat and easier to drain.

You can install several more drains. Increase moisture and water protection measures. Tiles do not choose too large.

First of all, when making the ground, you should use a spirit level to make an angle, so that the ground not only looks flat, but also easy to drain.

Professional decoration team, professional staff, plan in advance, choose the furniture you want, choose your favorite materials.

There will be some failures in the use of flushing toilets, the most common problem is that the toilet drain is not smooth, simply put, the toilet drain is not smooth or directly blocked after flushing. Don't panic when you encounter a bad toilet drain, first recruit what is the cause of the toilet drainage, floor drain. The location of the floor drain is generally set in the shower area, the position of the toilet in the inside, and the corner of the wall, which is convenient for the organization of drainage slope, and the window is convenient for ventilation and drying, so as to avoid dampness and mildew.

<> the location of the floor drain installation in the bathroom wants to get the best visual effect, when the plumber installs the water pipe in the early stage, he should try to arrange the floor drain position in the middle of one brick or the symmetrical angle of four bricks according to the size of the bricks. The floor drain should be installed slightly below the overall plane, so that it drains quickly and does not accumulate water. The paving of the floor drain should be cut into four corners in a radial shape, and the zigzag sink.

Generally speaking, the installation slope of the drainage branch pipe of the bathroom is required to be no less than 3, and it is recommended that 5 is the best. The slope of floor drain pipe drainage is the key, and everyone must pay attention to this.

Tile joints are also a nook where water can be easily stored. Therefore, the beauty seam construction must be done, and the kind of beauty seam parallel to the tile (scraper seam), not the kind that is concave (edge ball seam). Generally, a slope of 2% is better, because if the slope is too high, it may cause some inconvenience to the use of other key parts of the bathroom.

As the saying goes, "people go to high places, water flows to low places", if you want to drain smoothly, you must do a good job of slope when laying tiles, and the slope should lead to the floor drain. Generally speaking, the slope of the bathroom floor is 2% 3%, of course, in order to achieve a better effect, you can also make a little larger slope.

The slope is good and the drain is not fast, because the drainage of the bathroom floor is mainly drained by the floor drain, and the bathroom floor drain should be bought U-shaped floor drain, because there are double water outlets around the floor drain, and the drainage volume is large, and the water will of course shoot faster!

1. Dun cloth method: mopping the floor of the dun cloth.

First put the cloth at the mouth of the toilet, and then put water to ensure that the water submerges the cloth. Then press the cloth hard, stuff it into the toilet mouth as much as possible, and finally lift the cloth as fast as possible, repeat this action, the things in the toilet will be sucked out, and the pipe can be unblocked.

2. Find a longer section of plastic water pipe, connect the tap water at one end, plug the toilet mouth into the toilet mouth at the other end, and then block the toilet mouth with rags and other things, and then turn on the tap water, which will use the water pressure to dredge the pipe.

3. Go to a 2 yuan store or grocery store to buy a manual dredge (something that looks like a spring), and dredge it yourself, and a dredge is a few yuan.

Specific causes and solutions:

1. Slight blockage of the toilet: Generally, the toilet blockage is caused by toilet paper or sanitary napkins, towel rags, etc., which can be dredged directly by using a pipe dredging machine or simple dredging tools.

2. Toilet hard object blockage:

Accidentally fall into hard objects such as plastic brushes, bottle caps, soaps, and combs when using. This kind of blockage is mild, you can directly use a pipe dredging machine or a simple dredging device to dredge directly, and when it is serious, you must disassemble the toilet to dredge, and this situation can only be completely solved by getting things out.

3. The toilet bowl is aging and blocked

The toilet has been used for a long time, it is inevitable that it will scale on the inner wall, and in serious cases, it will block the vent of the toilet and cause the toilet to drain slowly.

4. Toilet installation error:

Generally, it is divided into: the outlet at the bottom is not aligned with the drain, the screw hole at the bottom of the toilet is completely sealed, which will cause the toilet drain to be unsmooth, and the water level of the toilet tank is not high enough to affect the flushing effect.

5. Squatting pit to toilet:

Some old houses are installed when building a squatting pit, the bottom of the sewer pipe is used U-shaped waterproof elbow, when recreating the toilet, it is best to replace the bottom elbow with a direct bend, if you can't change it, then you must do a good job of cleaning up the bottom bend before installing the toilet, and the installation is to avoid letting cement or tile fragments fall in.

6. Hair causes sewer blockage:

After a period of use of the sewer, the hair that usually takes a bath will hang on the pipe wall and accumulate too much, which will cause blockage, and the hair will generally cause the toilet floor drain to be blocked, the washbasin to be blocked, the bathtub to be blocked, and the shower room to be blocked. Therefore, when you usually use it, you must cover the floor drain cover and other protective facilities, and if you have hair, you can pick it up and throw it into the trash.

What should I do if my hair is too much and my drain is clogged? This kind of blockage is easy to solve, you can dredge the water with a hand-cranked dredge, and if it is serious, you have to use a pipe dredging machine.

Precautions If none of the above solutions work, then you can only hire professionals.

Whether it is the tank level or the sewer level, please specify.