Difference Between Eight Hole Flute and Six Hole Flute The distance between the various holes of the

The traditional flute is generally six holes, and now the improved flute has increased to eight holes, the purpose is about two, one is because the finger holes of the six holes are too large, especially the flute in F key E key is generally born small people are really not good to press the truth, and the other is more for the convenience of transposing, in the two fingering methods of 3 and 6, the second hole and the fifth hole need to be often used to open half a hole (referring to the six-hole flute), such a half-hole sound is not easy to grasp the pitch, and it is more difficult to master the timbre.

Therefore, between the first and second holes and the fourth and fifth holes of the six-hole flute, two semitone holes are added, and the ring finger of the right hand and the middle finger of the left hand are used respectively to facilitate the transposition, and other aspects are actually the same.

The flute is divided into six holes (5 in the front and 1 in the back) and eight holes (7 in the front and 1 in the back), and the principle of the flute is similar to that of the flute. The finger spacing of the six holes is relatively large, especially the F tune, which has a certain difficulty in blowing or flipping, so the modified flute is used in professional performances, which is the eight holes, and the eight holes are 2 semitones more than the six holes, so that the finger distance is shortened and more suitable for the use of the human hand, and the flipping is easier. Therefore, it is recommended to choose an eight-hole one when you are a beginner.

The main differences between an eight-hole flute and a six-hole flute are the number of sound holes, the difficulty of transposing, and the support points. Specifically:

1.Number of sound holes: An eight-hole flute has six sound holes and a barrel tone, while a six-hole flute has five tone holes and a barrel tone.

2.Difficult to transpose: The eight-hole flute is not easy to transpose and is suitable for fixed tuning, while the six-hole flute is easy to transpose and is suitable for the first tuning.

3.Support point: the eight-hole flute finger hole is close to each other, generally the left hand uses the first knuckle, the right index finger, middle finger, ring finger all use the second knuckle, the little finger uses the first knuckle, and the right thumb is naturally placed in the middle of the index finger and middle finger on the back of the hole flute.

To sum up, the main differences between the eight-hole flute and the six-hole flute are the number of sound holes, the difficulty of transposing and the support points.

The flutes are all the same flutes.

It's just that the eight holes are an improvement of the six holes.

The eight-hole flute has two more semitone holes.

After blocking the 26th two semitone holes, it is the same as the sixth hole Xiao.

There is no difference between traditional and popular.

The eight-hole Xiao is to open two more holes on a six-hole Xiao.

But with the addition of those two semitone holes, it is much more convenient to transpose.

I used to learn the six holes first.

Later, I found out that eight holes were more convenient.

And now there are very few six-hole Xiao in the piano shop.

It's all eight-hole.

It's not easy for you to buy a six-hole one.

You don't have to pick and choose.

After learning six holes, change to eight holes.

Not handy.

It's awkward.

The fingers and sound hole positions have changed.

It takes a while to find the feeling.

Readaptation. It is recommended to buy one.

G tune eight holes. Because the hole spacing is small.

Easy to take. After adapting, change the F tone.

The f. Hole spacing is large.

My F-tuned flute is a six-hole flute, and the hole flute is an eight-hole flute, so it's just as easy to use. The old Taoist elders said that now some people say that the qin flute is eight holes, which is completely wrong, the qin flute is specially designed for the accompaniment of the guqin, how can there be eight holes? Don't even have the most basic ancient ** common sense?

Hole spacing: (the first hole is pressed by the thumb behind the tube body, and the data is the distance from the bottom end of the mouthpiece to the center of each hole).

The first hole (the top hole behind the thumb): 246mm; Second hole: 274mm; Third hole:

The sound outlet hole behind the pipe body: 504mm (can open one, can also open a pair, if open a pair, the data is 506mm); Decorative holes: 566mm (open double holes).

The diameter of each sound hole is about 7 mm.

Related Introductions

Hole flute, wind and air sounding instrument. It is a very ancient musical instrument of the Han nation, referred to as the flute, which is one of the most common national musical instruments, most of which are made of purple bamboo, but can also be made of white bamboo. It is often used in ensembles with the guqin or in traditional silk and bamboo bands, and is also used for solo playing.

The two flutes are respectively engraved with dragons and phoenixes to pair them, which is called "dragon and phoenix flute". The solo repertoire includes "Partridge Flying", "Autumn Thoughts on the Dressing Table", "Willow Shakes Gold", etc., and the ensemble pieces for piano and flute include "Three Alleys of Plum Blossoms", "Flat Sand and Falling Geese" and so on.

Is LZ going to make his own flute?

Hole spacing: (the first hole is pressed by the thumb behind the tube body, and the data is the distance from the bottom end of the mouthpiece to the center of each hole).

First hole (top hole behind the thumb): 246mmSecond hole: 274mm

Third hole: 295mm

Fourth hole: 316mm;

Fifth hole: 360mm;

Sixth hole: 388mm

Seventh hole: 407mm;

The eighth hole: 430mm (can be appropriately sideways according to the position of your little finger) The sound hole behind the pipe body: 504mm (can open one, can also open a pair, if open a pair, the data is 506mm); Decorative holes: 566mm (open double holes).

The diameter of each sound hole is about 7 mm.

Is LZ going to make his own flute?

Hole spacing: (the first hole is pressed by the thumb behind the tube body, and the data is the distance from the bottom end of the mouthpiece to the center of each hole).

First hole (top hole behind the thumb): 246mmSecond hole: 274mm

Third hole: 295mm

Fourth hole: 316mm;

Fifth hole: 360mm;

Sixth hole: 388mm

Seventh hole: 407mm;

The eighth hole: 430mm (can be appropriately sideways according to the position of your little finger) The sound hole behind the pipe body: 504mm (can open one, can also open a pair, if open a pair, the data is 506mm); Decorative holes: 566mm (open double holes).

The diameter of each sound hole is about 7 mm.

Hello dear. The parameters of 8 holes are as follows.

Hole spacing: (the first hole is pressed by the thumb behind the tube body, and the data is the distance from the bottom end of the mouthpiece to the center of each hole).

First hole (top hole behind the thumb): 246mmSecond hole: 274mm

Third hole: 295mm

Fourth hole: 316mm;

Fifth hole: 360mm;

Sixth hole: 388mm

Seventh hole: 407mm;

The eighth hole: 430mm (can be appropriately sideways according to the position of your little finger) The sound hole behind the pipe body: 504mm (can open one, can also open a pair, if open a pair, the data is 506mm); Decorative holes: 566mm (open double holes).

The diameter of each sound hole is about 7 mm.

Hope it helps, thank you!

Hello teacher, what is the length of the eight-hole flute, and what is the inner diameter of the tube, I use the inner diameter of the copper pipe is millimeters, thank you, teacher.

The fingering of the eight-hole flute is as follows:

On the fingering chart, a black solid circle indicates that the sound hole is fully pressed, a hollow circle means that the sound hole is open, and half black and half white means that half of the sound hole is pressed.

The distance between the finger holes of the eight-hole flute, generally the first knuckle of the left hand, the second knuckle of the index finger, middle finger and ring finger of the right hand, the first knuckle of the little finger, and the thumb of the right hand are naturally placed in the middle of the index finger and middle finger on the back of the hole flute.

The support point of the eight-hole flute: the support finger and the playing finger should be completely clearly divided, each responsible for its own responsibility, and not mixed with each other.

There are many support points for the six-hole flute, a total of five: lips, left middle finger, left little finger, right big finger, right little finger.

The eight-hole flute has few support points, only three points: the lips, the little finger of the left hand, and the big finger of the right hand.

The hole is counted from the bottom up 1234567 behind is the 8th hole.

Scale from low to high: 5 (a little below, "bass sao"): full press, "slow blow".

7 (low): only open one, two, three holes.

1: Open only one, two, three or four holes.

2: Only press six, seven, eight holes.

3: Press only the eighth hole.

4: Only press five, six or seven holes, this reason does not have to stick to fingering.

The six-hole flute has six holes, and the eight-hole flute has eight holes. The sound holes of the six-hole flute are the first five and the last one, and the eight-hole flute is the first seven and the last one. The eight-hole flute is a product of modern improvements. The flute is generally divided into a hole flute and a qin flute, both of which are single-piped and vertically blown, and it is a very ancient Han wind instrument.

The flute is generally made of a bamboo pipe, which is longer than the curved flute, with a bamboo section at the upper end, a hollow section at the lower end and the inner tube, and a mouthpiece open at the edge of the upper end, from where the air is blown and pronounced. It is generally made of purple bamboo, yellow withered bamboo or white bamboo, with a total length of 70-90 cm, slightly longer and thinner than the Qudi, the inner diameter of the tube body is centimeters, the upper end is left with bamboo knots, and the lower end and the inside are hollow.

The sound quality of the flute has a lot to do with the bamboo material selected and the production. To choose the winter solstice to the spring equinox of the harvested bamboo, the growth period of more than three years of old bamboo is better, the bamboo should be solid, the weight is heavier, the purple bamboo to the bamboo flowers uniform, purple-brown is better, no insects, shrinkage, splitting, bee waist and belly and other defects, the tube body is complete, the texture is fine and straight.

When making, the mouthpiece and sound hole should not necessarily be in a straight line, especially below the E key, and the sound hole should be ergonomically opened according to the more comfortable position of the fingers. The mouthpiece is round above and below, the sound hole should be round, and all are cut into an inward inclined shape, the hole wall should be smooth, the inner chamber should be smooth and clean, the bamboo is polished, the two ends are flat, the diameter of the two ends can not be too large, and the lacquer decoration should be beautiful.

Hello, the punch size of the six-hole flute is: the blow end of the hole flute can be 18mm, the piano flute can be 16mm, and the south flute can be about 20mm. The calculation of the base pitch is based on the 38cm length of the base pitch of the flute with a more suitable barrel tone of g, and is calculated according to the common ratio of 2 to 12 powers or the three-point profit and loss method, which is in line with the actual situation.

I hope mine is helpful to you and I wish you a happy life.