How to disassemble the chassis of the gas stove and how to disassemble the gas stove

The disassembly of the gas stove is divided into four processes:

1.Twist and external thread moisture-proof cap disassembly.

Pull out the knob upwards first, then rotate the external thread moisture cap in the opposite direction.

2.Remove the fire cover and opening.

The gas stove fire cover can be removed immediately. Then you can see the three screws that hold the non-moving port in place. After removing the screws, the drain pan can be used.

3.Use a wallpaper knife to draw a circle between the panel and the bottom shell.

A two-sided sponge strip is applied between the bottom shell of the gas stove and the panel, which is fixed and immovable. In the case of disassembling the panel, it must be cut with the cutter head.

4.Remove the gas hob panel.

Place the stove flat on the countertop, press the stove with your left hand and pull the laminated glass up with your right hand.

panels can.

The internal structure of the gas stove is detailed in detail.

The internal structure of the gas stove is composed of a single pulse, an oil circuit plate, a stove, an ignition needle, a magnet extinguishing induction needle, and a battery box. The most important of these are the single pulse and the manifold plate. This is also the area where gas stove applications are very susceptible to harm.

Here are just three of the most important components.

Single pulse: the key component of high-voltage charging and discharging of gas stoves. Single-wire RTD.

For ignition only. The single pulse of the multi-wire RTD should show the amount of current 6 seconds before the extinguishing route.

Oil circuit board: gas stove natural gas channel monitoring center, gas stove ignition switch, and the city where its thermal resistance extinguishing relay is located. The most important part of the gas stove component.

Stove: the primary gas blending place of the gas stove, the supply and demand balance of the natural gas management center and the external fire.

The above is the detailed information about the disassembly of the gas stove, I hope it will help you.

1.Pry with a screwdriver.

If the base of the gas stove is rusty, you can pry it up with a screwdriver on the premise of heating. Do not close the gas stove valve before doing it.

2.If the base of the gas stove is rusty, you can drip the oil on the rusty place, let it loosen slowly, and then pry it down, of course, you must pay attention to safety, and be sure to close the gas stove valve.

3.Beat slowly.

If the base of the gas stove is rusty and cannot be removed, you can knock it for a while, knock it loose, and then lift it up forcefully.

The method of disassembling the gas stove is shown in the figure below:1. First of all, turn off the natural gas valve of the gas stove.

2. Then remove the bracket on the gas stove.

3. Next, pull out the fire cover on the gas stove.

4. Then take out the base of the gas stove upwards.

5. Finally, the gas stove was disassembled.

1.Remove the screws that hold the panel in place and remove the control knob to remove the service panel behind the panel by unscrewing a set of screws on the edge of the panel.

2.To access the burner assembly, remove the stove rack and remove the top of the gas stove. The top of the gas stove should be lifted completely off, or the hinge should be lifted to the back. ”

Dear, I'm glad to answer for you: A natural gas stove can be disassembled in this way: 1. Remove the screws used to fix the panel and unplug the control knob.

The knobs on the control panel are friction-fit and can be pulled out directly. Some knobs have set screws in the base, which are removed with a screwdriver or universal wrench, and then the knobs are pulled out, and the service panel behind the panel can be removed by unscrewing a set of screws on the edge of the control panel. 2. If the stove is flat with the countertop, you can open the cabinet door under the stove, hold it with your hand and gently lift it up.

2. Then remove the bracket on the gas stove, as shown in the figure below.

3. Next, pull out the fire cover on the gas stove, as shown in the figure below.

5. Finally, the gas stove was disassembled, as shown in the figure below.

Take the ** cover to see if there are screws, and loosen them if there are; If not, pick up the flame distributor again, you should be able to see a few screws loose, release the gas knob, and open the panel.

Be careful not to be too rude and damage the lines, especially the gas pipes.

It's best to ask a qualified professional to clean up and safety comes first.

How to disassemble the gas stove is as follows:

Turn off the gas valve, unplug the gas pipe, remove the fire distributor and pot holder, and loosen the water tray screws with a scattered Phillips screwdriver. If the ants rust for a long time, use vinegar drips on the rusty screws to rust, remove the water tray, pull out the ignition button, pull it up from above, use a wallpaper knife to separate the glass panel and the bottom shell, remove the glass countertop and the disassembly is completed.

Before the 80s of the 20 th century, the development of China's gas industry was still relatively backward, the popularity of urban gas was very low, only a dozen percent, and almost no one in the vast rural areas used gas. At that time, the gas stove was in the initial stage of material notification, and the product structure was simple and the function was single. Previously, each gas appliance had only the simplest gas stove, and the product structure was also very simple.

Most of the cooktop materials are cast iron, surface plating or spraying, etc., there is no electric ignition device, and the process is also in a relatively primitive state.

Introduction to the development of gas stoves

After 1980, with the deepening of reform and opening up, the market economy has risen, and all kinds of foreign gas appliances have entered China, and the number of gas appliance manufacturers has increased from more than 10 to nearly 100. The types of enterprises have also developed from the original single gas company to various types of enterprises such as state-owned, collective, and private, and well-known foreign gas appliance manufacturers have also begun to look for partners in China.

As a result, the quality and appearance of the products of gas appliances have also changed fundamentally, and the varieties and functions of the products are also constantly changing. During this time, the panels, combustion system, ignition device were also improved. The panel material is sprayed with cold plate, the burner has a cast iron stove head, surface electroplating or zinc spraying, and the ignition device adopts piezoelectric electronic ignition, which improves the ignition rate and improves the durability and reliability of the gas stove.

The operation steps for disassembling the gas stove are as follows:Material preparation: iron frame, screwdriver, rag, etc.

1. Check whether the gas valve is closed to avoid potential safety hazards caused by gas leakage.

2. Clear the debris around the gas stove and find an iron frame to suspend the gas stove.

3. Use a suitable screwdriver to unscrew the screws on the gas selling rock stove in turn.

4. Place the unscrewed screws properly, and then open the sealing cover on the gas stove.

5. After completing the above steps, lift the tempered glass panel of the gas stove.

6. The disassembly of the gas stove is completed.

Close the door of the gas valve: Close the gas valve of the gas stove to ensure that the gas does not flow out again.

Disconnect the power supply: If the gas stove has a power plug, unplug the power plug first.

Remove the gas stove: Remove the stove from the gas stove one by one, which can be removed with a screwdriver or wrench.

Disconnect the gas pipeline: Untie the gas pipe on the gas stove from the gas interface, and disconnect the gas pipe from the gas stove.

Move the gas stove: Depending on how the gas stove is installed, you may need to remove the screws or nuts that are fixed to the base and then move the gas stove carefully.

It is important to note that for the sake of Ahn Zheng Sheng, it is best to have the gas stove dismantled by a professional to ensure proper operation and avoid potential hazards.

Dear, hello, there are the following steps to disassemble the gas stove: 1. Turn off the gas valve 1The first thing to do is to find the gas valve that was turned on when installing the gas stove, hand twist the valve, and turn it off.

2.Unscrew the pipe connection on the gas pipe and remove the gas pipe. 3.

Turn off the switch on the oscilloscope completely. 2. Pay attention to safety 1The gas volume reading on the gas meter should not be too high, generally less than 1 liter, and it can be safely disassembled.

2.During the disassembly process, wear a helmet and gloves. 3.

Cherish life, and care must be taken during the dismantling process to avoid any unsafe incidents. 3. Disassemble the gas stove 1Disassemble the handle and remove the handle with a change cone.

2.Remove the gas stove from the mounting bracket in the opposite direction of the installation steps, and then disassemble the gas stove. 3.

Place the disassembled gas stove in a safe and dry place for transport or disassembly. Just follow the steps above and do it. <>

2. Then remove the bracket on the gas stove, as shown in the figure below.

3. Next, pull out the fire cover on the gas stove, as shown in the figure below.

5. Finally, the gas stove was disassembled, as shown in the figure below.