How to deal with water seepage on the wall outside the bathroom and how to repair it

Bathroom leakage will always occur, such as bathroom leakage to smash the ground to repair it is too expensive, and it is more difficult to restore the original state before smashing, if the bathroom leakage does not want to smash the tile treatment method is as follows: 1. Analyze the causes of bathroom leakage There are many situations of bathroom leakage, and each repair method is different. When you find that the bathroom is leaking, first look at what the water is leaking, for example, it may be a leak of the waterproof layer, you need to make a new waterproof layer, if it is a water pipe problem, you need to repair the water pipe, you can change the water pipe.

If you don't want to smash the floor if the bathroom is leaking, you must first check that it is leaking. 2. I don't want to smash the ground, and the bathroom leakage repair treatment method is a problem with the upper and lower water pipes. And the water pipe is underground, so you need to consider smashing the floor, but it's not....

If you find that the outer wall of the bathroom is moistened, you can make a waterproof hand or tarpaulin on the outer wall of the bathroom.

If the exterior wall is leaking, you can find the property for repairs.

Water seepage on the exterior wall of the bathroom does not need to be repaired as long as it does not affect the use of your home.

Contact the upstairs homeowner and the property management company first, and go to the upstairs homeowner to check the situation on the spot.

First of all, close the water valve as much as possible to avoid further leakage. Check the leakage points one by one, you can first put the gap between the heating pipe and the casing, the sewer pipe, the floor drain, and the root of the wall are all easy to leak locations, and in the case of cleaning and drying, evenly apply glass glue to seal it. Then use a seam or waterproof glue to coat and seal the gaps between the tiles.

Do not use water for 24 hours. Test the water after 24 hours. Secondly, you can drill multiple small holes at the water seepage on the top surface of your home according to different positions, and then use a syringe to drive the waterproof paint into the holes.

The expansion of the waterproof coating blocks the internal gaps, and then achieves the effect of waterproofing. This is a simple grouting waterproofing treatment. After the above treatment, the general leakage situation can be solved.

How to deal with toilet leakage and how to repair it.

1. If the upper and lower pipes are broken, the pipes should be replaced.

2. If there is water seepage on the ground, please follow the steps below to fix the toilet leak.

1. Clean dust, oil stains and stagnant water on the surface, and keep the surface dry.

2. If the tile joints are filled with caulk, you need to use a knife to cut a small groove.

3. Spray penetrating waterproofing agent on the surface of the tile, tile joints, wall joints and pipe roots, and ensure uniform spraying.

4. After the waterproofing agent is 90% dry (about 2 hours later), fill all tile joints and damaged parts with seam sealant.

5. After waterproof construction, the construction site shall not be wet with water within 24 hours.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

The wall outside the bathroom is leaking, and it is necessary to do waterproof treatment on the outside, so that it can be repaired.

Water seeps through the exterior wall of the bathroomWhat is the reason?

1. Water pipe leakage: When the water pipe is put into the bathroom, the water pipe joint is not tightly connected. During use, leaking water pipes can also cause leaks in the outer wall; 2. The waterproof layer is not good

Second, the waterproof layer is not good. leads to exterior wall water filtration; 3. Insufficient drying tiles: there are two ways to paste wall tiles and floor tiles.

Bathroom tiles are dry-mounted, which can cause water leaks in the walls.

Water seeps through the exterior wall of the bathroomHow to deal with it.

Water seeps through the exterior wall of the bathroom1. If the toilet pipe is leaking, the following method can be used because the water pipe is hidden in the wall. If there is a leak, you can first determine the location of the water pipe according to the construction drawing, then plan the wall, find the leakage point, repair or directly replace the water pipe, and the water filtration problem can be solved.

Water seeps through the exterior wall of the bathroom2. If the waterproof layer is not ready, you can remove the tiles from the bathroom wall first, and then apply a waterproof coating on the original waterproof layer to increase the thickness of the waterproof layer. When applying the waterproof layer, it is necessary to pay attention to the principle of thin and multi-layer coating, keeping the thickness above millimeters. If the height of the waterproofing layer is not enough, you can increase the height of the waterproof coating in the original waterproofing layer, and then replace the mosaic decoration.

Water seeps through the exterior wall of the bathroom3. If the tiles are not dried properly, the surface of the wall will leak. If you want to solve the problem, you can only put the original tile in a dry place. At the same time, the dried cement mortar is cleaned, the base layer is re-leveled, and the wet web forming process is adopted.

Construction is underway. Water seeps through the exterior wall of the bathroom4. If the paint on the wall is incorrect, the wall will leak. If you want to solve this problem of Yinpei, you must first remove all the painted surfaces of Huaibo Mountain, and then repaint the walls when they are dry. Before painting each wall, it is essential to make sure that the top paint is completely dry, otherwise it will cause the same problem.

Water seeps through the exterior wall of the bathroomRepair plan: 1. Ask professionals to apply penetrant to the place where the water seeps on the external wall, follow the three steps of inspecting the wall, drying in the lead, and painting. 2. Ask professionals to inspect the exterior wall from the top of the wall to the bottom, and if cracks are found, they should be coated with penetrant, and each crack should be treated not less than 2 times.

The above refers to:Water seeps through the exterior wall of the bathroomI think everyone understands the reason! The problem of leakage from the outer wall is very common. When solving a problem, you first find the specific cause, then solve the problem and solve it thoroughly.

You can get it for free

Treatment and maintenance methods of water seepage on the wall of the bathroom:

1. Apply permeable waterproofing to the outer layer of cement, such as the outer layer of ceramic tiles, tile joints, corner gaps, and pipe roots, and the agent needs to ensure that the coating is balanced.

2. After the waterproofing agent has dried for 9 percent, take the joint sealant to fill all the tile joints and damaged places, and then take the joint sealer to strengthen the fragile places around the pipe root.

3. The gaps between the ground and the wall and around the pipeline need to be waterproofed with plastic steel mud.

4. After the waterproofing is done, do not touch the scene with water within 24 hours, the bathroom is leaking, if the pipe is broken, the pipe needs to be replaced.

5. Finally, clean up the dust, oil stains and stagnant water on the outer layer so that it can be kept dry.

Methods for testing water seepage in the bathroom

Common toilet water seepage can be divided into two categories, one is ground water seepage, and the other is water seepage caused by water pipe damage.

1. When taking a bath or mopping the floor every day, it is easy to accumulate water between the ground and the wall, which leads to leakage, which belongs to ground water seepage.

Pipeline seepage is identified through inspection, such as non-pipeline leakage and ground water seepage.

2. Pipeline seepage refers to the problem of water seepage due to damage in the places where the upper and lower water pipes, floor drains, and toilet interfaces occur.

If it is water seepage from the upper pipe, it will be continuous, uninterrupted or the infiltration situation will slowly worsen, and the main valve of the water pipe needs to be turned off.

If you find a large amount of water seepage, it means that the pipe is damaged and needs to be replaced.

The easiest way to fix water seepage in the bathroom is to use a penetrating water repellent agent.

Scope of application: Suitable for waterproof layer breakage. This method is the easiest to operate, but it has a shorter lifespan. Basically, it takes three or five years to do a new penetration waterproofing.

Construction method: Buy a permeable waterproofing agent, pour it on the floor after mixing with water, spray it on the wall, and brush it on pipe joints, tile gaps, floor drains, etc. Wait for the penetrating waterproofing agent to dry naturally, and after 24 hours, clean the jelly-like waterproofing agent from the tiles.

Principle: Permeable waterproofing agent is to follow the flow of water to the damaged part of the waterproof layer, and use its strong penetration ability to cover the nearby floor slab. After the waterproofing agent dries, it automatically forms a waterproof membrane. This membrane can block the broken waterproof layer.

Water seepage is generally divided into two types: one is ground water seepage; The second is the leakage of water pipes. If it is water seepage on the ground, there will be corresponding water seepage on the roof downstairs; If the water is stopped and the seepage disappears, this is the problem.

If the water pipe is leaking, we can pour water into the floor drain and toilet to judge whether there is a problem with the sewer pipe; If you don't use water for a few days, and the forest water phenomenon continues, it is a problem with the water pipes.

If the bathroom is determined to be waterproof layer water seepage, the amount of work will be relatively small, and we do not need to pry up the floor tiles. We can choose some new penetrating waterproofing agents to waterproof the surface of the bathroom floor again, so that the water cannot penetrate into the ground through the gaps. On the contrary, if there is a problem with the water pipe, then the only way to pry up the floor tiles is to pry up.

We replace the water pipes so we don't have to work on the entire bathroom floor.

The treatment and maintenance methods of toilet leakage without smashing bricks are as follows:

1. Clean the bathroom floor first and check what the cause of the water leakage is. If there is a slight leakage and the water pipe is not damaged, you do not need to smash the tiles, and you need to use a penetrating waterproof material.

2. Keep the ground dry enough, and then apply the penetrating waterproof paint to the ground, paying attention to every part to be smeared, and no leakage of coating.

3. After the waterproof is dry, you need to use glass glue with good waterproof performance or beauty sewing agent in the gap of the tile, and wait for it to dry thoroughly after treatment.

4. If the water pipe is broken, it is generally necessary to smash the tiles and then repair the water pipe. If you don't knock on the tiles, you can only reinstall the water pipe to ensure the later use.

How to prevent water leaks in the bathroom

1. When the bathroom is decorated, it is necessary to do a good job in the protection of the waterproof layer, and try not to damage the waterproof layer, otherwise it is very likely to cause water leakage in the later stage and bring unnecessary trouble. If there is a leak caused by accident, it needs to be repaired in time.

2. If you need to replace the tiles, you must protect the original waterproof layer, and after knocking off the tiles, level the wall and then redo the waterproofing to avoid water seepage. At this time, it should be noted that polyurethane waterproof paint should be used and brushed about 2 to 3 times.

3. Special attention should be paid to the waterproofing of the wall, which must be done, and the height should be controlled at about 30cm. If there is a bathtub installed, the wall around the bathtub should be waterproofed to the left and right.

Water seepage on the bathroom wall may be a leak in the water pipe or a leak in the waterproof layer, and the specific solutions are as follows:

1. Water pipe leakage: If it is a water pipe leakage, we need to chisel the bricks on the wall, and then observe the water pipe inside to see if the nuclear fiber is leaking.

2. Waterproof layer leakage: waterproof layer leakage in two situations, if the leakage is not particularly serious, then we only need to coat a layer of waterproof treasure on the wall to avoid water seepage in the bathroom, but if the water seepage is very serious, then we need to smash the bricks open, and re-lay the waterproof layer inside.

The specific cause of water seepage on the bathroom wall

1. Water pipe leakage

When laying water pipes in the bathroom, if the construction is not improper, the water pipe interface is not tightly connected, there will be leakage and other problems in the process of use, and the water pipe is mostly laid along the wall, once the leakage will lead to the phenomenon of damp water seepage on the bathroom wall. In addition, cracks due to the quality of the water pipes themselves can also lead to leakage problems.

2. The waterproof layer is not done

If the water seepage on the wall of the bathroom is serious after showering, and it improves when not showering, and the water seepage is located on the wall where the back water surface is located, it is very likely that the waterproof layer of the wall is a problem. The water seepage problem caused by the waterproof layer is mainly divided into two situations, one is that the thickness of the wall waterproof layer is not enough, and the other is that the height of the wall waterproof layer is too low. If you want to improve the problem of water seepage, you need to solve it in a targeted manner.

3. Improper dry paving of tiles

If the wall tiles and floor tiles of the bathroom are paved with dry paving process, then it is very likely that the water in the lower layer of the dry paving bricks will seep out along the wall surface due to improper construction, so that the problem of water seepage will occur.

Hello, glad to answer for you. Dear, be sure to do wall waterproofing, before laying wall tiles, do a good job of wall waterproofing. Generally, the wall should be waterproofed with a height of 30 cm, but for non-load-bearing light walls, the whole wall should be waterproofed, at least 60 cm high.

The joints between the wall and the ground and the joints of the pipes between the water and the water are the most problem-prone places, and the workers must be urged to deal with these edges and corners, and the waterproof coating must be applied in place. Resurface the floor tiles to make the floor waterproof, if you need to replace the original floor tiles in the bathroom. After the original floor tiles are chiseled, the ground must be leveled with cement mortar first, and then waterproofed, so as to avoid leakage caused by uneven thickness of the waterproof coating.

Before doing the way, the floor should be cleaned up. Try not to destroy the original waterproof layer, and the ground of the building that is ready to use the new delivery of the embassy is generally made of waterproof layer, so there will be no leakage without destroying the original waterproof layer. The decoration team is required to do a good job of cement mulch for the upper and lower water pipes of the bathroom, brush 10 to 20 cm of waterproof paint from the ground, and then redo the ester waterproof on the ground, plus the original waterproof layer is sensitive to cracks, forming a composite waterproof layer to enhance waterproofness.

I hope my answer can help you, thank you, dear.