What is the reason for water seepage in the master bedroom of the new house decoration 1 meter away

It may be that the water pipe falls off and leaks It is recommended to find someone to inspect Your problem is too simple, I don't know what pipe you are, and I don't know what the specific situation is, if it is an old iron pipe or other material of the water or sewer pipe has a leakage, and it can't be replaced for the time being, I will tell you a simple way to plug the leak, first of all, you have to prepare materials, buy 2 4 pipe pinch(pipe hoops) If you are 4 pipes, then you have to buy 6 points or one inch pipe pinch, Then buy a roll of high-voltage insulating tape (these two things are generally available in building materials stores), and it is best to go to the old man who repairs the bicycle to buy a bicycle inner tube, the materials are complete. First use insulating tape to spirally wrap the leakage section, preferably more than two layers (note that the insulating tape must remove the separator) and then wrap 1 or 2 layers of bicycle inner tubes, and then tighten the pipe pinch. Do it yourself, it's very simple, and replace the PPR tube when it's convenient.

I don't know if I can help you.

It is estimated that the embedded water pipe is not connected, and the leakage is not accurate on paper, so it is recommended that the bathroom should be better to do secondary waterproofing + secondary drainage.

The water pipe is broken, or the bathroom is not waterproofed properly.

Ask if there is a water pipe when you renovate it, and whether it is the ground or the roof, the ground may be open with pipe joints, and the roof is the problem upstairs, and you can notify the upstairs residents.

It may be that the bathroom was not waterproofed properly.

What should I do if there is water seepage on the wall of the master bedroom with bathroom? The bathroom is a place with more water. If used for a long time, in many cases, water leaks and seeps will occur on the walls, affecting everyone's life.

In view of the problem of water seepage in the bathroom, the following small version introduces the method of water seepage treatment of the bathroom wall and how to detect the content of the water seepage strip in the bathroom! Clause.

II. II.

II. Chapter II.

Bathroom wall leakage water treatment method: What should I do if the wall of the master bedroom with a bathroom is leaking?

1。The first step is to find out the cause of the wall leakage, and then take the right measures to deal with it. If the water pipe is leaking, we have to find the leak in the water pipe. If the waterproofing is not good, it is necessary to do a good job of waterproofing the wall.

2。Leaking water pipes. If the water pipe is broken and causes water seepage, you need to dig the wall tiles, find the water pipe joints, see if the water pipes are broken or the joints are leaking, then replace the water pipes, and then restore the wall tiles.

3。Shoot noisy leakage of waterproof layer. If the waterproof layer leaks, you need to flatten the floor tiles, find the leakage, and then smooth it with a waterproof plugging treasure, and finally apply waterproof paint. If the waterproof height is not enough, resulting in water seepage on the wall, you need to dig out the high tile, re-waterproof, and then lay the tile.

How to detect water seepage in the bathroom: What to do about water seepage on the wall of the master bedroom with bathroom?

There are two causes of water seepage in toilets, one is groundwater leakage and the other is water seepage caused by a ruptured water pipe. There are two ways we can check for water seepage in the toilet:

1。Ground leakage.

1) Under normal circumstances, when bathing or mopping the floor, it is easy to generate water between the floor and the wall, and infiltration, that is, the bathroom is the floor leakage.

2) Inspect by the method of inspection to identify pipeline leaks, if it is not a pipeline leak, it may be a surface leak.

2。Pipeline leakage judgment.

Pipe leakage refers to leakage caused by rupture of upper and lower sewer pipes, floor leaks, toilet joints, etc., which can be checked in the following two ways:

1) Leakage of the upper tube.

If the upper pipe leaks, the leakage will continue to occur uninterruptedly, otherwise the leakage will continue to increase. At this time, the main valve of the water pipe should be closed in time to reduce the leakage immediately.

2) Leakage of sewage pipes.

You can turn on the faucet or drain the water to the ground. If you notice an increase in leakage from sewer pipes, it means that the pipes are damaged and leaking. At this point, you need to replace the sewer pipe.

What should I do if there is water seepage on the wall of the master bedroom with bathroom? Summary:

The owner has only lived for more than half a year, and the bathroom has been a little leaky these days, and I found a master to check it, only to know that it was because the construction was not done during the construction of the waterproof beam. For the owners who don't know anything about decoration, they don't know what the waterproof beam is that the master said, and their eyes are clouded. The master saw that the owner looked like he was about to cry, and quickly told the owner what the waterproof beam was, saying that it was too late to remedy!

It turns out that the waterproof beam is necessary to do in the bathroom, kitchen and balcony at home, and other rooms can not be done. It is to make a small partition similar to a retaining wall on the ground when building a wall, because the kitchen and bathroom are in contact with water for a long time, making a waterproof beam can prevent moisture from returning along the wall, and causing the wall to invade water. It is very simple to make a waterproof beam, and it can be mixed and poured with cement, sand, and gravel in proportion.

Thinking that it was so easy to do, the owner's workers didn't even do it at the beginning, which was really unreliable. The owner's sister on the side suddenly became anxious, and quickly asked the master, what if the waterproof beam is not made, but the wall has been built?The owner's sister Pi Ji's house has just been renovated, and it seems that she is not worried about her workers.

The master said that if you don't do the waterproof beam, you must pay attention to the waterproofing in the future, and do the waterproofing several times in the corners and corners of the ground, and it is best to put it for a longer time when doing the closed water test, and if there is a problem, it can be remedied in time.

Hearing this, the owner's sister hurriedly called ** home and asked about the situation, hoping that her family would not have this kind of eggplant situation in the owner's house!

Causes of water seepage: because the mixed mortar is not rounded, the gray joints are hollow, and the capillary safety channel produces a siphon effect: the raw materials on the inner surface of the decorative arts are loose, and the moisture in the capillary is easy to disperse;The wall thickness of the surface is uneven, and it is concluded that the water is poured quickly and slowly, the plaster is easy to joints and fall off, and the bottom edge of the grid does not gather, there are holes in the gravel, which causes the wall to leak, the door and the window of the wall are not sealed, the sill of the sash is higher than the inner table, and the outer sill plate is not easy to produce a gentle slope, causing water to be exported.

There is no obvious blockage between the rear frame and the wall or polyurethane paint, or the protective tape of the window is not damaged, causing water infiltration. Other holes are not blocked correctly, and the toilet is considered to be a very susceptible area to water seepage because it is a place with a lot of water, such as showers, flushing toilets. Inevitably, the long-term will cause some small gaps, so that the water above can seep into the house gradually in the building, the water pipe under the roof leaks, the hidden water pipe or solar power water pipe in the house will inevitably seep water for a long time, which will produce a certain degree of dampness and cold on the wall.

Remedy: The next door neighbor's water main does not have moisture protection at the junction between the water main and the floor. It is likely that there is a leak around the water mains, and the water flows down the water pipes, causing the roof to leak.

The underground water pipe in the toilet is leaking, we are looking for the leaking part of the water pipe, but it is very difficult to find the leaking part of the underground water pipe, after all, we can't see or touch the hidden pipe.

Generally speaking, the location of water seepage is at the joint, so it is necessary to find the joint position after the wall bricks are planed, and then check whether the drainage pipe of the decoration partition is seepage, if there is, it is necessary to replace the water pipe or socket, and then pave the wall, and sit on the surface of the moisture-proof tile can be repaired. The water seepage of the embedded parts of the wall is caused by the moisture return of the wall, which mostly occurs in the area close to the top of the toilet, the house and the living balcony, and the water seepage is generally the water seepage at the junction position, including the water seepage on the wall surface of the roof of the building.

Wall deashing refers to the condition that the alkaline substances in the wall are melted into the water by water after the wall of the engineering building is re-damp, and the alkaline solution is sent to the surface of the wall with the volatilization of water vapor, and crystallizes and is dry and solid on the surface of the wall. The wall you see is full of black hair, and the more serious ones you can see that the surface of the wall paint turns yellow, and the wall blisters and falls off.

First of all, you should close the valve of the bathroom at home, if it is still seeping, it means that there is a water leak upstairs, if you don't judge well, you should ask a professional repair worker to see; You can find out if there is an aging water pipe in your home, or if the joints are damaged, you can also go upstairs to see if it is leaking, replace the leaking pipes in your home, or ask a professional repair worker to repair it.

You should first check whether there is a serious rupture in the waterway of the bathroom, turn on the faucet, observe the location of the bleeding, and then use a professional instrument to detect whether there is a leak on the roof. After digging the leakage area, check the water pipes, repair the water pipes, and repair them again.

It can be effectively judged according to the area of water seepage, as well as the frequency and length of water seepage; You can check whether the joints of the water pipes are tightened, whether there is water leakage, you can also see whether the water pipes are damaged, or check whether the waterproof layer of the building is faulty.

I think you can check your own waterproofing system first to determine if there is a water leak, and if not, you can ask the people upstairs to see if it is their bathroom leaking; If you have a problem yourself, be sure to ask a professional to replace it in time.

The bathroom with slight water seepage on the wall and floor is a must-have space for every family, and a clean and dry bathroom environment can bring people pleasure. The waterproof height of the bathroom wall is generally 30cm high, so how to do the waterproof of the bathroom? Let's take a look.

1.First of all, the ground treatment of the bathroom containing socks mold is flattened, and then the waterproof treatment is slowed down, so that the waterproof coating can be effectively avoided and caused by water stain leakage, and the thickness of the joint should be painted, the gap between the wall and the ground contact between the bathroom and the gap between the upper and lower pipes and the ground is the most likely place to cause problems, so the waterproof coating in these places must be applied in place. 2.

The treatment of the bathroom wall also directly affects the effect of the bathroom waterproof treatment, in the general bathroom waterproof treatment, the wall should be coated with a height of 30 cm waterproof coating, so as to better prevent the water seepage of the wall, if the wall of the bathroom is not a load-bearing light wall, then it is recommended that the entire wall is painted with a layer of waterproof coating, and then the wall adjacent to the bathtub should be coated with waterproof paint higher than the height of the bathtub. 3.After the construction of waterproof treatment in the bathroom is completed, a waterproof test should be carried out to block all the sewers of the sanitary napkins, and then fill the toilet with a certain amount of water, and wait until 24 hours later, and then check to see if there is any water leakage.

Note that this step is very important, it is the key to ensure the quality of the toilet waterproofing project. The above is about the practice of bathroom waterproofing, I believe everyone has also understood! After mastering these good Zen knowledge, it will be helpful for the decoration of your home.

There are two main reasons for water seepage into the bedroom wall in the bathroom

1. There is leakage of the buried plumbing pipeline in the wall.

When carrying out the construction of plumbing pipes, the use of unqualified materials and non-standard construction leads to the leakage of the plumbing pipes buried in the wall, which leaks into the bedroom wall on the outside of the bathroom.

2. The waterproof treatment of the bathroom is unqualified.

When the bathroom is doing the waterproofing treatment of the wall and ground, the waterproof material is unqualified and the painting is not standardized, which leads to the water storage test and other operations, and the moisture of the wall and ground of the bathroom leaks to the bedroom wall outside through the crack of the waterproof layer.

To identify whether there is unqualified waterproof or unqualified installation of plumbing pipelines, you can check whether the waterproof treatment meets the requirements by doing a closed water test and a water test on the waterproof layer, and check whether there is leakage in the plumbing pipeline by doing a pressure test on the plumbing pipeline.

1. If the waterproofing of your own bathroom is not done well or the water pipe of the inner wall is broken and leaking, and the water penetrates and soaks the wall, the only way to deal with it is to redo the waterproofing or find the leaking water pipe to repair.

2. In the same way, if you have the same situation in the bathroom upstairs, find a neighbor or property, and the treatment method is the same as above.

3. Upstairs, maybe the house across several floors seeps into your home through the pipe, pipe groove, etc., this problem is very difficult to find, and the property should cooperate with the investigation one by one. After finding the leakage point, pour asphalt paint into the pipe groove or line pipe to seal it.

Waterproofing is not done.

Bathroom waterproofing as far as possible to use polyethylene polypropylene tarpaulin to do, the ground is full of paving, overlap and back to the wall can not be less than 10cm, close to the bedroom wall if in the shower area, need to do the wall height of the wall waterproof.

The downstairs neighbor said that there was still water seepage, which means that there is water leakage in your house. According to the description, you should be tested to rule out water that is leaking from the pipes.

I have buckled all the tile joints on the ground and wall and re-slipped them with white cement + Lauyal, and also glued all the joints on the ground and the wall, "Who made you do this?" With many years of operation in my industry, this is basically useless and fooling people. Because:

The mixture of white cement and emulsion is difficult to fill the gaps between the tiles and tiles, and it cannot prevent cracking, so it cannot play a waterproof role; (It just so happens that I also know glass glue) in the ground and wall joints to play glass glue, the craftsmanship is not good, it is not easy to glue and seal, and the glue is not very good weather-resistant glue, so that the glue can not be tightly bonded with the wall and the ground, and can not play a good role in preventing water leakage.

There was no leakage during the water test, and leakage occurred in the later stage. The reasons are: 1. The height of the waterproof is not enough, the ground is all done, the wall of the shower area is 180cm or the height of the top, and the height of other walls is 30cm.

2. The quality of waterproof materials is unqualified. Is not used polymer cementitious waterproofing coating (two-component). 3. The waterproof layer is damaged in the later decoration.

The seepage water mentioned by the downstairs neighbor may be the sediment water that originally leaked.

The best and most effective way is to re-do the bathroom waterproofing, and pay attention to the protection of the waterproof layer during the later decoration.

Leibangshi - home waterproofing expert.