How to make a chair out of cardboard

Take scissors and carefully cut off the top cover. 2. Scissor tube. Cut vertically along the aluminum cylinder to the bottom of the can, cut about 20 strips, of course, the finer the cut, the more delicate the effect of the finished product, and make the whole like a tassel after the can tube is upside down, do not cut off the aluminum strips.

3. Shaping up. Turn the jar barrel upside down so that the bottom is facing up, so that the bottom is the face of the chair. Fold the head of the aluminum strip twice in the same direction, not too much, as long as it looks sleek and not prickly.

Find four points, three or four aluminum strips at each point, tidy up and tie them up, that is, four chair legs, between the two adjacent legs, there are loose aluminum strips, these aluminum strips are erected up along the bottom of the can, shaped, and made into the back of the chair, and the remaining loose aluminum strips on three sides can be cut off along the bottom of the can. Such a simple chair is ready. Of course, you can also use your imagination to make it more delicate, and the loose aluminum strips can also be made without cutting, and it is also good to make the pattern on the armrests and the front of the chair.

With the bought, the outer bread is a layer of cardboard. Absolutely not.

The simple way to make a cardboard stool is as follows: first we need to prepare the materials, the old cardboard that kills the refrigerator for fallen leaves. Then cut out the two good sizes as shown below, about the same width of cardboard.

The picture below is just the main material. Then we need to step on the cardboard with our feet, the main purpose is to make the cardboard soft and easy to roll up later. As shown below, a small piece of cardboard donated by fallen leaves.

The process of rolling must be tight, and then fix a circle on the outside with adhesive tape.

Next, the cardboard roll is wound on top of the small cardboard roll, so that the cardboard roll becomes thicker and thicker, as shown in the figure below. The steps are the same, and then fix with adhesive tape after rolling. DIY fixed bench:

And the sponge surface, when the roll reaches a certain width, we fix it with adhesive tape, and then cut out a bucket with the same circle up and down. Then, as shown in the figure below, attach the cardboard to the top of the paper bucket.

Then cut the sponge into 3 long strips to cover the size of the stool, and the size should be able to cover it completely. Next, it's up to you to call it a day and fix it yourself with art scissors! Make the size of the sponge the same as the size of the bench surface, as shown below, and you need to be patient.

Next, we need to make a stool-sized sofa cover, as shown below, an old garment ready to be thrown away. Heavy cut the middle in half with scissors. Then the old clothes are covered by the widest square, and the sleeves are removed, and <>

Then wrap two squares of cloth around the round cardboard bucket of the stool, remember to enclose them with the reverse side, and sew them together with a needle and thread. Be sure to tighten the bully so that you get a cardboard bucket the same size. Use scissors to cut out a round cloth of the same size as the surface of the stool and sew it together.

Remember to suture the same on the reverse side.

Put the sponge into the fabric sofa cover first, and keep the sponge round as shown in the picture below. You can put it piece by piece, don't let the sponge position too loose. Then put the sofa cover directly on top of the cardboard bucket.

So the basic shape of the stool comes out. The first sample of a stool made of fallen leaves is shown in the picture below.

1.Brief introduction.

A cardboard stool is a simple and low-cost chair that is usually used for situations where you need to sit down for a short time to rest or use a temporary seat, such as camping, picnics, exhibition venues, etc. The cushions and brackets are made of thick cardboard, which is very convenient to make and also has the best ability.

2.Preparation of materials.

Materials required: thick cardboard, scissors, ruler, pencil, small incision opener can be prepared as needed (scissors can also be substituted).

3.Steps:

Determine the size of the stool as needed, and use a ruler and pencil to draw the rectangular stool and bracket on cardboard. Usually the size of the bench surface is 40 30cm, and the height of the stand is 30-40cm, on this basis, appropriate adjustments can be made.

Using scissors or openers, cut out the stool surface and the stand separately along the pencil lines.

Cross and stack the stool and bracket together so that they fit snugly and use the core cutter to cut out a few small notches at the joint.

Form both sides of the bracket outwards into a V-shape, and buckle the stool surface on the lifting bracket to ensure that the seat surface is stable and firm.

4.Precautions.

When making cardboard stools, it is necessary to ensure the quality and thickness of raw materials to ensure the stability and load-bearing capacity of the seat.

Great care should be taken when folding and disassembling the stool to avoid damage to the bracket and affect the stability of the structure.

Since the weight capacity of the cardboard bench is limited, special care should be taken when using it and not exceeding the support range.

5.Conclusion.

The cardboard bench is a simple, low-cost, portable and lightweight seat, especially suitable for outdoor camping, picnics, exhibition venues and other scenes that need to sit down for a short time to rest or use temporary seats. With the above steps, you can easily make your own cardboard stool that provides convenience and comfort for a variety of outdoor activities.

Making paper stools:

1. Materials: waste newspaper paper, rope, glue, cloth.

2. Spread out the newspaper flat and apply glue. Roll up each piece of newspaper and make it into a solid column.

3. Put the pillar-shaped paper vertically, put it together neatly, and make a round stool, just like a tree stump, and then tie it with a rope.

4. Finally, use a cloth with Zen slow material to cushion it, and a stool is ready.

Fold a small round table and two or three chairs, it's really a bit like playing a game of house wine with your friends when you were a child! The following is the hand-in-hand chair origami method I brought to you, I hope it can help you!

Prepare materials: a 15cm*15cm square piece of paper.

Chair Origami Ode to the Blind Tutorial:

Step 1: Divide the paper into quarters.

Step 2: Fold one of the halves upwards and then fold the left and right sides in half.

Step 3: Fold the two corners of the closed end to the crease adjacent to the ascending limb to get the crease.

Step 4: Hold the first divisions on the left and right sides with your fingers and flatten them down along the crease.

Step 5: Fold the small square in the middle up, then fold the top side down a bit. Wild laughter.

Step 6: Fold the right-angled trapezoids on the left and right sides to the left and right respectively, deepen the creases, and then open them, and open the small square in the middle downwards as well, and a chair is folded.