Hello, ASUS motherboard has not been able to enter the installation interface, how to solve it?

If you want to boot the computer and enter the BIOS directly, it is recommended to try the following steps:

1) If you can't find the device that can be turned on, please confirm whether you recognize the hard disk, reset the hard disk to turn it on, and then confirm whether the problem is solved.

2) Under the BIOS, see if the other settings are abnormal, whether the time is restored to 0:00 on January 1, if so, you can try to update the BIOS, or replace the CMOS battery of the motherboard (CR2032).

3) If it occurs every time you boot up, please test the situation of starting the hard disk of the single connected system to minimize the test.

The motherboard has not been able to enter the installation interface, it should be stuck in that interface to turn off and turn it on again.

If your ASUS motherboard has not been able to enter the working state, it may be that there is a problem with its installed system, and you can reinstall the system and it should be solved.

Hello, you first have to enter the BIOS interface of the computer, and then set it to boot from the USB disk boot disk, and you can install it.

You can check the motherboard BIOS to see if you can find a hard drive or SSD. There is also whether the disc or USB disk of the system you make is normal.

Install the USB flash drive boot software correctly, if it is a new motherboard, it is recommended to use the latest version to boot the software version.

Motherboard underlying hardware control system". To put it simply, this is a motherboard main control system, and if the BIOS is set incorrectly, the motherboard may not work properly.

Second, the problem analysis of automatically entering the BIOS when the computer is turned on

1. Keyboard failure: This is a fault situation that many users ignore, and the general motherboard is set to press the "del" key to enter when the computer is turned on.

BIOS settings.

and the "del" key on the user's keyboard or the number key ".".(del)" key failure (such as stuck, internal adhesion, etc.), resulting in only the BIOS can be entered after booting, and only the BIOS can be entered after restarting.

2. BIOS setting error: As mentioned earlier, "BIOS is the main control system of the motherboard, and the wrong setting may lead to the failure to operate normally", so when the BIOS is set incorrectly, it may lead to boot only into the BIOS, and the reboot is still.

You can try rebuilding the boot manually.

1 After shutting down and restarting the computer three times, select [Troubleshooting] [Advanced Options] [Command Prompt] in order, and the computer will automatically restart. Then we select the account and enter the password to enter.

2 Then insert the system boot USB flash drive, and in the command prompt interface, we execute the [bcdedit enum] command to check the boot corruption. This is shown in the figure below.

3 Run the following command to repair the main boot record of Windows 10.

Rebuild the BCD configuration file.

bootrec /scanos】

It is used to scan the operating system that has been booted and recorded after the installation is successful.

bootrec /fixmbr】

Used to repair MBR records for traditional bootstrapping.

bootrec /fixboot】

Used to repair corrupted sectors.

Steer. bootrec /rebuildbcd】

It is used to reconstruct and repair the BCD boot record, and the operation is completed after this step is completed.

<>4 Then use the [bcdedit enum] command to check the rebuild of the boot, as shown in the following figure. Suibi.

Then see if you can enter the system, it should be noted that the operation interface may be different due to different system versions, etc

You are prompted to enter the BIOS to adjust the settings, and press DEL or F2 or F8 to enter the BIOS

Then follow the prompts on your ** to set it up. It is estimated that the BIOS battery of Hello Hole is dead. Shenzhou changed the battery.

Summary. After the computer is turned on, the monitor has been the ASUS motherboard page, and it can't enter the system, the solution:

You can try, press "F8" when you boot up, press Enter, Enter, "Enter Safe Mode", find: "Last correct setting", press down, try.

If it still doesn't work, it is recommended that you do: "One-click restore". See this is the "Restore System" method, which will not only help you repair and restore your computer system, but also save all the files on the disk.

After the computer is turned on, (it can only be operated after the computer "brand")! Press the "One-Click Rescue" shortcut key on the far right of the keyboard ("+" sign on the keypad) (press F2 or F11 for laptops), and then press "Deep One-Click Restore" for a while, and wait for the system to "rescue and copy" all disk files, (Note:

After the restoration is done, you can't shut down or restart the computer, you should immediately "enter the main platform", that is, "desktop", otherwise "all the previous efforts will be wasted" and "the restoration will be invalid"! The computer is immediately back to the "factory state"! Start "360 Security Guard" and "360 Antivirus Dual Engine Edition" to start scanning for viruses and Trojans and patching computer vulnerabilities!

Factory state": It is the state when I first bought it, the software is there, there is no need to "reinstall the system", and it is much more "worry-free" than the heavy installation! Or, take out the "manual" when you bought the computer and compare it with "restore the system"!

After the computer is turned on, the monitor has been on the ASUS motherboard page, and I can't enter the system, what should I do?

After the computer is turned on, the monitor has been the ASUS motherboard page, can not enter the system, the solution: you can try, boot press "F8", press "enter", "enter safe mode", find: "the last correct setting", press down, try.

If it still doesn't work, it is recommended that you do: "One-click restore". See this is the "Restore System" method, which will not only help you repair and restore your computer system, but also save all the files on the disk.

After the computer is turned on, (it can only be operated after the computer "brand")! Press the "One-Click Rescue" shortcut key on the far right of the keyboard ("+" sign on the keypad) (press F2 or F11 for laptops), and then press "Deep One-Click Restore" for a while, and wait for the system to "rescue and copy" all disk files, (Note:

After the restoration is done, you can't shut down or restart the computer, you should immediately "enter the main platform", that is, "desktop", otherwise "all the previous efforts will be wasted" and "the restoration will be invalid"! The computer is immediately back to the "factory state"! Start "360 Security Guard" and "360 Antivirus Dual Engine Edition" to start scanning for viruses and Trojans and patching computer vulnerabilities!

Factory state": It is the state when I first bought it, the software is there, there is no need to "reinstall the system", and it is much more "worry-free" than the heavy installation! Or, take out the "manual" when you bought the computer and compare it with "restore the system"!

No, press F8 or return to the motherboard page.

Let's reinstall the system.

The reason why your ASUS laptop can't get into the system after booting it up may be due to a recent improper shutdown.

Here's how:

1. Push the F8 button after powering on.

2. Enter the advanced options interface.

3. Use the arrow keys to select and click on the last correct configuration option.

4. After restarting the computer, you can enter the computer normally.

Notes:1. When using the computer, it is necessary to back up the computer files regularly to prevent the loss of files.

2. In the process of using the computer, the computer should be cleaned regularly.

3. In the process of using the computer, the computer must be operated in a standardized manner.

4. In the case of not knowing the problem, be sure to contact professional personnel for processing as soon as possible.

Step 1: First, enter Safe Mode and remove the recently installed driver software.

Boot to WinRE (Windows Recovery Environment), which can be understood as recovery mode.

You can press and hold the power on button until the machine is powered off, then turn it on again, and then power off again, repeat 3-5 times until you enter the recovery mode as shown below.

From the Select options screen, tap or click Troubleshoot.

Tap or click Advanced options, and then select [Startup Settings], ., .,Select [Start], click the safe mode environment you want to enter, and in general, it is recommended to select (4) to enable safe mode.

Second, with the Auto-Repair feature, you can detect and resolve certain system issues that prevent Windows from booting.

To run automatic repair, follow these steps:

Boot to WinRE (Windows Recovery Environment), which can be understood as recovery mode.

You can press and hold the power on button until the machine is powered off, then turn it on again, and then power off again, repeat 3-5 times until you enter the recovery mode as shown below.

From the Select options screen, tap or click Troubleshoot.

Tap or click Advanced options, and then tap or click Automatic repair.

Auto-Repair will launch and attempt to fix Windows to prevent loading.

If the above still doesn't work, try restoring the system, or reinstalling the system.

Steps: 1. Try to enter safe mode for debugging.

1. Press the power button to turn off when you turn on and enter the system, and repeat about 3 times;

2. Click on the "Troubleshoot" option, then click on "Advanced Options", click on "Restart" under "Startup Settings", and select "Safe Mode" after restarting.

3. In safe mode, you can uninstall the previously installed software and check and kill viruses in a comprehensive way;

4. After entering the safe mode, if you have installed anything before the black screen, you can uninstall and delete the software in the safe mode, if you are not sure, you can do a clean boot, and the operation steps of the clean boot are as follows:

1) Press "Win+R" to open the "Run" window, enter the msconfig command and press enter, the system configuration dialog box will pop up.

2) Switch to the "General" tab, click "Selective Startup", and then click Clear the tick above "Load Startup Items".

3) Switch to the Services tab, click Hide All Microsoft Services, and then click Disable All.

4) Switch to the "Startup" tab, tap "Open Task Manager", tap Startup Items, and click Disable.

5) After clicking OK to save, reboot the system.

Second, in order to fully rule out the possibility of software or system problems, you can back up the hard drive data and reinstall the operating system in safe mode;

1. Press the power button to turn off when you turn on and enter the system, and repeat about 3 times;

2. Click on the "Troubleshoot" option, then click on "Advanced Options", click on "Restart" under "Startup Settings", and select "Safe Mode" after restarting.

3. Troubleshoot - Initialize the computer.

Third, the software debugging is invalid, and it is recommended to go to the after-sales service to test the hardware.