How to disassemble the keys of the notebook keyboard?

The first step is to find a breakthrough. At first glance, there are no screws exposed on the keyboard, except for the keys, only the rest of the indicator panel is visible. However, it can be seen that under the bezel of the panel are hidden two screws that hold the keyboard in place.

When disassembling, it is best to use a hard sheet such as a blade, insert it into the gap and slowly lift the baffle and pry it off.

The third step is to lift the keyboard. Now only a few bayonets under the keyboard can fix the keyboard, first lift the keyboard and then pull it out in the opposite direction, as shown, but be careful while pulling out the keyboard, don't pull the back of the keyboard too hard to break the connecting wire.

After these four steps, the keyboard is successfully removed, and at this time, you can not only completely clean the dirt of the keyboard, but also clean the dust inside the notebook by the way: such as the dust on the CPU fan, so that your beloved notebook can be renewed. After cleaning, it is time to put the keyboard back on, and when installing, be sure to align multiple bayonets with force to succeed.

Of course, the brands on the market are different, the models are different, so the structure of the internal manufacturing is also different, but as long as you continue to explore and use your brains and hands, draw inferences from one another, I believe you can also make this book glow.

Some have a full snap design, while others include screws. If there are screws, remove the screws first, and the buckle will be warped with a small screwdriver or metal sheet, pay attention to the direction of the buckle, don't use too much force so as not to affect the appearance, don't take the keyboard board too far after it is warped, and pay attention to the following cables. ]

There are two kinds of notebook keyboard disassembly The first is to be completely dismantled The second is to have several dark cards on the keyboard (most of them are four), and the dark card can be removed by putting the dark card inside and down, and most of them are the second kind].

You didn't say what brand your laptop was. My notebook is HP Compaq, and I will tell you about my experience of disassembling the keyboard of the notebook, I hope it will help you. Look at the bottom cover of the notebook, there are some signs next to the screw mouth:

There are disc markers, memory markers, hard disk markers, and keyboard markers. The keyboard markings are a lot like keyboards, and you can tell them at first glance. Then unscrew the screws marked with the keyboard (usually three) so that the keyboard is out of the screws, and then use a tool to gently pry the keyboard from the front, and that's it. ]

The method of disassembling and installing the keys of the notebook keyboard is as follows:

Disassembly: The ease of taking the button is actually about the same as doing "1+1". Pick the top of the button with your hand and pull it in your direction with a little force, and the button will be removed.

At this time, there may be two results, one is to just pull out the button Jianchang potato cap, and the other is to pull out the button bracket together.

Installation: Install the bracket first, then the keycaps. The combination of stents is the most difficult of the difficulties, and this link must have enough patience, of course, it is very simple after getting acquainted with it.

After the buckle relationship is done, you can fix the bracket on the keyboard base. After the middle bracket is installed, the keycaps are installed back.

How to maintain a notebook keyboard

1. After smashing the keyboard, everyone should consider the damage and impact of dust on the keyboard. Bought a keyboard protector to cover it on. It can be waterproof, dustproof, and wear-proof, and it is not expensive.

In this way, most of the dust will be blocked by the keyboard cover in the process of ordinary use, as long as you clean the keyboard cover on time.

2. If you really don't want to add a protective film to the keyboard, then we can clean the keyboard on time. Use a keyboard brush to clean crevices, or gently blow dust out. Then wipe the surface of the keyboard with a quick cleaning solution. If you don't have a keyboard brush, you can use a soft toothbrush instead.

3. Of course, a reminder, try not to put anything with liquid next to the most important thing, if you accidentally spill the cup on the keyboard, you can only change it obediently.

1. ShutdownWhen disassembling any part of the notebook, we must first shut down the computer to avoid unnecessary damage to the computer. This is an important step that should not be omitted.

2. The next step is to remove the keycaps, use tweezers, first gently upturn from one side of the keyboard jujube ear, warp a little, and then change to the other side, the action should be light, when you find that one side is warped up with tweezers a lot, the keycaps are still not loosened, you should immediately change to the other side, you can't believe that the miracle is strong.

3. Check whether the scissor foot base of the key and the keycap are damaged or fall off, if the four card slots on the keycap are damaged, you can only replace the appropriate keycap, if the scissor foot base falls off or is not paired well, you can use tweezers to adjust it carefully, not vigorously, not forced.

4. After the installation is confirmed that the scissor foot base is paired correctly and the keycaps are not damaged, press the keycaps on the scissor base and press diagonally with two fingers until the keycaps are completely installed. Remember: don't wear the keycaps backwards and don't install them too hard.

5. Turn on the computer for boot detection, then open a texter, press the key button just installed a few more times to see if there is any abnormality, and the installation will be completed if there is no abnormality. After I installed it, the U key was the same as other buttons, and it didn't feel weird when typing.

The above are the detailed steps for the removal of the pen mess beam chain notebook keyboard. Before disassembling the computer, it is important to pay attention to safety to avoid damage to the computer or personal injury. Once the removal is complete, be sure to double-check to make sure the keyboard is properly installed and working properly.

When removing the keyboard, you need to lift the keyboard up gently and forcefully, you can use tools to assist, but be careful not to use too much force, so as not to damage the keyboard or motherboard.

Laptop keyboards are one of the most commonly used input devices when we use our laptops on a daily basis. However, due to prolonged use or other reasons, the keyboard may need to be disassembled for cleaning or replacement. So, how to disassemble the notebook keyboard?

Below, let's take a closer look at the steps to remove the notebook keyboard.

Laptop keyboards are one of the most commonly used input devices when we use our laptops on a daily basis. However, due to prolonged use or other reasons, the keyboard may need to be disassembled, cleaned, or replaced. So, how to disassemble the notebook keyboard?

Below, let's take a closer look at the steps to remove the notebook keyboard.

After removing the keyboard, we can clean or replace it. If it is cleaning, we can use detergent or cotton swabs to clean it. If it is a replacement, we need to remove the original keyboard first and then install a new one. Wow Sun.

Before disassembling the laptop keyboard, be sure to turn off the computer and power off to avoid damage to the computer or personal injury caused by improper operation.

Notebook computer because of the small space of the keyboard design, not only the lack of independent number keys, some users will also feel very inconvenient to use, and the use of a long time, there will always be such and such problems, in the case of problems, the first thing we have to do is to disassemble the notebook keyboard to see if it is ** malfunction, so what to pay attention to before disassembling the notebook keyboard, then follow me to understand it!

1. Notebook keyboard disassembly method:

1. Most notebook computers are embedded keyboards, and this kind of keyboard will have a baffle on the top of the notebook keyboard, and the baffle must be disassembled before the keyboard can be disassembled. In the process of disassembly, the strip above the keyboard should be removed first, and when disassembling the strip, there are fixing screws on the back of the pole, and the screws need to be carefully removed to take out the strip.

2. The removal of the snap-on notebook keyboard will be simpler, the approximate method is to unscrew the screw on the back of the notebook first, pay attention to the position of the buckle when screwing, and then pry it open with a flat-edged screwdriver.

Second, what to pay attention to before disassembling the notebook keyboard:

1. First of all, we must know that it is not a simple thing to disassemble the notebook keyboard, which has some difficulties, and some skills need to be used, and it is best not to disassemble the new notebook computer, so as not to damage it in the process of disassembly, resulting in the computer can not be guaranteed.

2. Before disassembling the notebook keyboard, it is also necessary to figure out what kind of structure the notebook keyboard uses, because different notebook computer disassembly methods are different, and the difficulty of disassembly is also different. 3. There are three main packaging results of notebook computer keyboards: one is an embedded fixed notebook keyboard, one is a buckle-fixed notebook keyboard, and another is a screw-fixed notebook keyboard. It's best to understand these different types of keyboard structures before disassembling them.

For the first time to disassemble the notebook keyboard for novices, there will be a lot of unaccustomed to the book in the process of disassembly, and the process of disassembly will also cause damage to the keyboard due to strength and some external factors, so friends who want to disassemble the notebook keyboard, do not use brute force in the process of disassembly, and combine skills and methods to be the right way.