What are the tips for installing cold storage panels?

Attention should be paid to the installation of the vertical plate: first select a corner according to the site conditions, and locate (that is, the vertical plate and the floor are locked) to extend to both sides at this angle, only lock the vertical plate and the vertical plate, and locate the vertical corner when encountering it, and place the beautiful plate in a conspicuous place, when installed on the side of the evaporator, the drainage pipe should be done in advance, and the U-shaped bend and silicone need to be done outside the library.

Quality requirements for the installation of vertical plates for cold storage design and installation:

The conspicuous surface of the vertical plate is flat, the library board has no concave points, the head surface of the vertical plate is flat, the gap between the vertical plate and the vertical plate is uniform, and the vertical corner of the conspicuous place is level with the corner of the floor.

It depends on what board is used, but it is always necessary to grasp one point, and it must be well sealed, because the purpose of using cold storage board is to keep warm. The kuban of polyurethane is generally buckled and can be buckled together. But be sure to ensure tightness.

As an installer, you must first be patient, careful, and responsible. Finally, you must have the confidence to do a good job!

If you have these qualities, next, you can take a look at the craftsmanship of the installers in our company.

Anhui Jinxue refrigeration equipment****.

Address: Youth Industrial Park, Hefei Trade and Logistics Development Zone, Anhui Province.

How to install the cold storage board? The installation of the cold storage board is generally to install the cold storage bottom plate first, and then install the side wall standing board, the rear wall standing board, and the front wall standing board, and then install the cold storage roof. The cold storage board generally has a sequential number, and the combination of the convex and concave parts of the library board will be tightly locked in accordance with the order.

After the library body is built, use a special sealant to seal the joint between each library board and seal the glue at the joint.

If you provide library boards, cold storage accessories, etc., only need to install, then it depends on Zheng Slip to change the local cold storage installation master charging standards, if you also need to include library boards, cold storage doors, refrigeration units, cold storage accessories, etc., different manufacturers, different cold storage equipment ** is not a shout of judgment, specific reference to cold storage**.

Abstract:The construction of cold storage requires the participation of cold storage insulation board, so it is very important to purchase a suitable cold storage insulation board. So how do we choose cold storage insulation boards?

The purchase of cold storage insulation board should look at the thermal insulation performance, dimensional stability, and service life. After we have selected the appropriate cold storage insulation board through certain skills, we must install the ear belt. So how to install the cold storage insulation board?

Let's take a look at the detailed installation method of the cold storage insulation board. How to buy cold storage insulation board.

1. Look at the dimensional stability.

The polyurethane foam material of the cold storage will change in size (generally shrinkage) when the temperature changes drastically or at a low temperature for a long time, and the change in size is often reflected in the cracking or falling off of the foam, which will inevitably affect the normal use of the cold storage.

2. Look at the thermal insulation performance.

Cold storage insulation materials, the first requirement is its thermal insulation performance, these thermal insulation properties are not recognized by their own eyes, so we must choose those regular manufacturers of thermal insulation materials. Such manufacturers have carried out strict quality control in terms of material selection and production.

3. Service life.

In addition to the basic performance of the cold storage insulation board, its service life is also very important, when they are prepared with white materials, although the surface of these polyester materials is foam with good toughness and impact resistance, but after you use it in the cold storage for a period of time, it will become very brittle, so as to reduce the life of the insulation board. Therefore, although there is a slight brittleness in the initial stage, the brittleness will disappear after a few days, and then the stable performance of the cold storage insulation material will be maintained for a long time.

How to install cold storage insulation board.

1. Use 107 glue and cement to prepare and paste paste, paste polyethylene polypropylene cloth, first of all, on the wall, ground, column and beam, all the places that need to paste the air insulation layer must be thoroughly cleaned, remove the protruding particles and lumps, sweep away the dust, and clean it. Then the slurry is painted, and then the polypropylene cloth is pasted, and the lap is 8 10cm.

2. Scrape and coat the paste mortar with a thickness of 3 5mm thick on the outside of the dry and solidified air insulation layer, and paste the extruded insulation board, paste the insulation board of different thickness on the cold storage at different temperatures, and paste it at the wrong seam. The columns of the refrigerated He family library and the frozen warehouse are reinforced with special insulation nails, and the specific requirements are made in accordance with the requirements of the contract.

3. After the outer layer of the insulation board is brushed and painted with anti-cracking mortar, 300 grams of mesh cloth is laid, and the lap joint is required to be 3 5cm lap, and fixed with 16 iron wires made into riding nails, and then connected and fixed firmly with special nails for thermal insulation.

4. In addition to the laid mesh cloth, paint the anti-cracking mortar, and after the basic drying, the third surface layer is painted with anti-cracking mortar, so that the appearance is smooth and calendered, and the total thickness reaches 7 10mm.