I bought a bluetooth headset, and I accidentally fell it, and it was connected with a little noise,

It is not necessarily a problem of falling, the solution to the noise of the Bluetooth headset is as follows:

Eliminate the cause of debris and exclude the cause of the line. Start by cleaning the headphones and see if there is any debris in them. If you have a problem with the headphone jack connector, first dip cotton in a small amount of alcohol, wipe the plug, and then wipe it with a paper towel.

If the noise changes with the twisting of the cable, it should be a problem with the cable, and if there is a problem with the cable, you can try to change the cable.

Secondly, there are people around you who are electrifying or have a strong electromagnetic field.

When it also causes the Bluetooth headset to have a current sound, or if you hold two mobile phones at the same time and connect the ** too close to each other, there will also be a very strong current sound. For this reason, it would be nice to change places or put another phone farther away.

See if the headphone cable is broken or loose, rule out the appearance of hardware damage, and finally if all kinds of inspections of the Bluetooth headset are found to be okay but there is still a current sound, you can contact the seller, after-sales return, inspection and maintenance.

Computers have static electricity, which is also the main reason. Touch the iron part of the computer case with your hands, and if the current sound disappears, connect a piece of copper wire to the screw on the back of the computer at one end and ground at the other end. Whether the microphone is in a reinforced state.

I remove the microphone reinforcement. Because some sound cards don't support it.

There is a problem with the driver, and the driver that comes with the system may be used.

Or there is a problem with the driver, if so, you can change to a sound card driver.

If your Bluetooth headset accidentally fell and connected with a little noise, you can turn it off first, then charge it, and then connect him, if there is still a sound indicating that there is a problem, you can send it to a mobile phone store or a mobile phone store to repair.

It should be that the unit is loose, you can try to contact the merchant, some good service merchants will help you repair it for free, but you have to pay the freight yourself.

It must have been broken, so there is such a sound, it is recommended to go to the professional maintenance department to repair it, or you can go to the place where you buy Bluetooth headsets, so that he can see what is wrong?

I bought the Bluetooth headset, and I accidentally fell it, and then there will be some noise inside, it should be that the sound inside has been broken and the quality has deteriorated.

I bought the bluetooth headset, and I accidentally fell it, and it was a little noisy when it was connected, what should I do? I think there may be something wrong with the fall of this version of the headphones, I think well, if it doesn't work, if you think, maybe people don't care about it.

Then you have to contact your headphone brand after-sales.

The solution to the bluetooth headset that fell and there was no sound:

Brand model: Huawei Honor 10

System version: Huawei JKM-TL100

Software version: 1, first of all, we turn on the mobile, next, we click on to open Settings.

2, then, we click on Open System.

3, Secondly, we click to open developer options.

4. Finally, we can turn on the switch of Bluetooth absolute volume to solve the problem.

No, it won't. It's a signal problem. The generation of this low noise is due to the interference in the process of Bluetooth wireless signal transmission, which is a common phenomenon of Bluetooth headsets, and the decoding chip of the mobile phone will also produce a slight noise background in the process of analyzing audio;

There are some relatively cheap Bluetooth headsets due to the optimization of the chip and the poor anti-interference ability of the Bluetooth signal, which is more prone to noise floor, and the noise floor of generally higher products will be relatively slight; If the noise floor is too large to affect the effect of listening**, you can try using an adapter cable to use Bluetooth headphones.

After the Bluetooth headset cracks, you only need to glue it together with 502 glue. Because the surface of the Bluetooth headset is made of plastic, it will not affect the normal use of the headset after cracking.

Start by blowing along the edge of the earphones with a hair dryer, being careful not to blow directly on the headphone unit, which is where your ears are usually when you wear them.

The most important thing in the whole process is that you must not break the earphone beam when dismantling, and you must use your hand to hold the earphone unit to exert force, otherwise you will not cry if it is broken. Comparison between the original headphone cover and the new headphone cover. In fact, the material is not much different. Look, it's actually a layer of 3m glue.

After dismantling, there may be some residual 3M glue on the edge, which can be wiped clean with the included alcohol cotton pad.

The other side is taken apart in the same way. I vacuumed the dust a bit.

Blow the 3m glue of the new earphone cover with a hair dryer to make it easy to stick it firmly. Note that there are two small protrusions on the left and right earbuds, which should coincide with the two small holes on the left and right earcups.

It can be done in about ten minutes. After installation, press for a few more minutes, and then put on the headphones and listen for more than ten minutes** and you're done. Bluetooth headset, but if it cracks, there is only a way to glue it, and there is no other way, as long as it is not broken, it can be used.

There should be no way to repair such a state, because for this kind of manufacturer, the cost of his repair is relatively expensive, because your headphones should not be more expensive, so don't repair it, you can buy a new one.

Hello. If this situation does not affect the use.

Generally, no treatment is required.

If it affects the use, but it can be listened to normally.

Glue can be used for pasting.

Be sure to use small amounts less often.

Otherwise, it is likely to affect the appearance and damage the internal hardware.

Or go to the place where the electronics are repaired and deal with it.

The solution to the Bluetooth headset that doesn't ring after a drop is as follows:

1. First disconnect the bluetooth, then put the bluetooth earphone into the charging case, and place the bluetooth earphone in the correct position when putting the bluetooth earphone.

2. Restart the earphones after putting them on, reconnect with the phone after starting, and the Bluetooth headset will have a sound.

3. If there is still no sound, it may be that the speaker is broken, and it is recommended to bring the sail removal earphones to the after-sales maintenance office for inspection and maintenance.

The headset is a pair of conversion units, which accept the electrical signal sent by the **** device or receiver, and use the speaker close to the ear to convert it into audible sound waves. The headset is generally detachable from the **** device and is connected by a plug. The advantage is that you can listen to the sound alone without disturbing others; It can also isolate the sound of the surrounding environment, which is very helpful for people who use it in noisy environments such as recording studios, bars, travel, sports, etc.

Headphones were originally used on the radio and radio, but with the popularity of portable electronic devices, headphones are mostly used in mobile phones, walkmans, slag collectors, portable video games and digital audio devices.

From the perspective of the development of the entire audio industry, wireless headphones are still a new thing, the development time is not long, and it is still in the rising period, user demand is constantly improving, and users' expectations for wireless headphones are also increasing, which is a new test for the industry.

<> in daily life, we are using Bluetooth headsets, it can avoid annoying wire entanglement, you can talk easily in various ways, when we use it, accidentally drop the Bluetooth headset, it will not make a sound, what to do, let's take a look together!

If we accidentally drop the Bluetooth headset to the ground when using the Bluetooth headset, the first thing we need to do is to disconnect the Bluetooth headset.

When we disconnect the Bluetooth headset, we can put the Bluetooth headset into the charging case, and when we put the Bluetooth headset, we should place it in the correct position.

After we put the Bluetooth headset, we can restart the headset, and after starting, we can reconnect with the phone, and the Bluetooth headset will have sound.

If there is still no sound after we reconnect, it may be that the speaker is broken, and we need to take the headphones to the after-sales maintenance point to overhaul the Bluetooth headset.

Summary. 1. First of all, disconnect the Bluetooth and put the earphones in the charging case, which should be placed in the correct position.

2. Restart the earphones, you can reconnect with the mobile phone, and the earphones will have sound.

3. There is still no sound, it may be that the speaker is broken, take the headphones to the after-sales maintenance point for maintenance.

3. Enter the Bluetooth settings page of the mobile phone, in the paired device, unpair, then put the earbuds into the charging case and open the lid of the case, press and hold the function button for 2 seconds, when the indicator white light continues to flash, the earbuds will enter the pairing state, and try again after pairing;

4. Put the earbuds into the charging case, keep the charging case open, and then press and hold the function button on the charging case for 15 seconds until the orange light flashes quickly and release the button, at this time, the earbuds will be restored to factory settings, after the factory reset is completed, the earbuds will automatically enter the pairing state, and try again after pairing;

5. If there is still noise in the headset after operating the above methods, you need to go to the vivo customer service center with the headset and a valid purchase voucher for testing and processing, you can pay attention to WeChat *** "vivo" or "vivo customer service" to inquire about the address of the service center**, it is recommended to contact before going to ensure that there is a staff reception and then go over, so as to avoid delaying precious time and running in vain.