What should I do if my iPhone6 can t be turned on when water gets in

Motherboard issues. Tell you what emergency you need to do after the iPhone gets into the water:

1: Don't shake your phone to prevent the water inside from flowing and causing a larger area to get wet.

2: Shut down immediately, never turn it on.

3: Don't try to dry it with a hair dryer, if the motherboard touches the water, using a hair dryer is more likely to cause damage to the motherboard.

4: Use a paper towel to wipe the place where it can be wiped as much as possible, and then put the phone into a sealed bag full of rice, and do not move for 48 hours.

After 48 hours, 48 will absorb the water inside, step by step to ensure that there is no problem.

Or immediately go to a mobile phone store to clean the inside.

If the water enters the mobile phone, it should be sent to the mobile phone repair station for ultrasonic cleaning as soon as possible.

If the battery is removable, remove the battery as soon as possible to reduce the corrosion of the internal components of the mobile phone caused by the electrolysis reaction of the liquid; At the same time, it can also avoid the occurrence of the phenomenon of inability to charge due to the short circuit of the circuit and the empty battery.

If it is not cleaned, the liquid will leave impurities attached to the components after the electrolysis reaction, and its electrical properties will be affected for a long time, such as leakage, poor contact, etc., and in serious cases, the components or motherboard wires will be corroded.

The workaround is as follows;

1.Go to a nearby store for inspection and repair, 2Send it to the after-sales point for inspection and maintenance [after-sales is more expensive].

There are three definitions of repair, which are replacement parts, pure repair parts, modification according to function, maintenance and restoration, maintenance, maintenance, and repair.

Hurry up and fix it, while the parts inside are still corroded.

1. The emergency treatment of iphone6s when it gets water and can't turn it on.

1.First of all, you should salvage the phone as soon as possible and remove the battery immediately to prevent a short circuit; At the same time, you should also remove the SIM card to avoid losing your contact information. The longer it stays in liquids, the more damage your phone will suffer for life.

2.See if the Water Damage Sensor changes color. The "water damage test strip" is a white dot near the battery box, and if it has turned red, the customer service staff knows that it is not a problem with the quality of the device, but that you have used it improperly and caused the damage due to water ingress.

So don't expect repairs and insurance, and pay for your own phone repairs.

3.Hopefully, instead of salt water, your phone will fall into drinkable fresh water. Because salt water can form a "salt crust" in the delicate internal components of the phone.

So if your sock phone unfortunately falls into the seawater, you'll need to gently rinse it with fresh water – after removing the battery and SIM card, of course, and before the drying process begins.

4.Wipe every part of your phone with a cloth or paper towel and don't move or shake your phone too much so that water doesn't swim around inside your phone5Try wrapping your phone in a cloth or tissue for a few minutes to create a little "vacuum effect" and suck out too much moisture.

If possible, put the phone in a place with warm air circulation for a few hours.

5.After a few hours, you can try turning on your phone and hopefully there are no remaining corrosion or short circuits. If the charger works, but the battery doesn't, you'll have to replace the parts.

2. Four-step "rescue" method.

Step 1: After rescuing the phone from the water first, remove the battery as quickly as possible.

Step 2: Take out the SIM card of the phone, blot it with a paper towel, and let it dry in a ventilated and dry place.

Step 3: Find a hair dryer to blow cold air for an hour or two, then use an electric fan to blow it for a day and a night, and then put it in a ventilated and dry place for a day and a night. If neither of these works works, just put it in a ventilated and dry place to dry it, and turn it on after three days.

If you have a disassembly tool at hand, disassemble the mobile phone, and dry each part of the mobile phone separately, the effect is better).

Step 4: Generally speaking, if you don't soak in water for too long, the above three steps can be basically done. If it still doesn't work, it may be that the motherboard is broken, and it should be sent to the repair station as soon as possible to deal with it.

1. The solution to the problem that the iphone6 can't turn on when the water is in

1) After finding that water has entered, remember not to turn the machine on or off immediately. Remove the case and dry the body, such as the water stains on the iPhone 6, and clean the moisture in the SIM card slot. Remember:

It is not recommended not to use a hair dryer or a heater or stove to dry dry. Even if you use a hair dryer to blow it, don't use hot air, be sure to use cold air, otherwise it may cause deformation of the motherboard.

2) For the mobile phone with slight water ingress, you can put the mobile phone in the rice bag for 24 48 hours and then take it out, and the mobile phone can be saved. Because the equilibrium humidity of rice stored at home at the current temperature is between 50-70%, it can play a role in drying and slowly absorb moisture.

3) Look at the water damage sensor to see if it changes color, as the material turns red as soon as it encounters water. If it is, it means that the water ingress is more serious and it needs to be repaired as soon as possible. However, this situation is caused by its own reasons, so there is no warranty guarantee.

4) For most friends who have entered the water, the best advice is always that if you can disassemble and clean it, you must disassemble it for treatment. Otherwise, it is easy to rust or mold. Finally, you must go to a professional and reliable store, find a reliable master, and clean up the motherboard, inner screen, and cable from the inside to the outside, and do a chemical treatment if possible.

2. Introduction to iphone6

Scoop it out of the water as fast as possible (fast, every second) and turn off your iPhone immediately. Press and hold the power button until it turns off.

Remove all shells right away, as they will trap moisture. The screen protector can be left unpeeled unless you see visible blisters inside.

Dry your iPhone with a cloth, as dry as you can, you can wipe the screen, sides, and back with a cloth (t-shirt, socks, etc.) or absorbent materials. Pay special attention to the power buttons, volume buttons, mute switches, speakers, microphone, and audio output jacks, and try to wipe all visible moisture as much as possible.

Contact the after-sales center immediately for free inspection and repair.

1.Do not try to turn on the device immediately if there is water ingress. Because the iphone is a built-in battery that can't be removed, the motherboard will be short-circuited if there is water, such as Rong.

If it turns out, it will burn down the motherboard, causing irreparable consequences.

2.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

3.Wipe the circuit board with anhydrous alcohol and try to turn it on. Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

4.Send it to a repair center for repair as soon as possible. If the motherboard is severely corroded over time, it will cause irreparable consequences.

The Apple 6 can't be turned on when the water is in, and the Chengdu ** can be repaired.

Disassemble and clean the motherboard, 1, don't try to turn on or charge if there is water, because the iphone is a built-in battery that cannot be removed, and the motherboard will be short-circuited if the water is ingress, and if you turn on or charge, the motherboard will be burned, causing irreparable consequences.

2. First wipe the water outside the mobile phone with toilet paper, throw out the mobile phone water, and then use a blow dryer to dry the water. The wind is open to the maximum temperature and the temperature is medium.

3. Please send it to this repair center for repair as soon as possible. If the motherboard is seriously corroded over time, it will cause irreparable consequences. (Water ingress must be repaired in time).

The black screen of water ingress is generally short-circuited, if it is not burned out, then it can be placed in a water-absorbing place such as a rice tank to dry at a high speed, and it may still be used.

Depending on your situation, it may be burning, but there is a turnaround.

If there is no water in this part of your phone, then it is possible that the test strip did not detect water ingress. Apple's warranty does not cover water ingress repairs, relying on this paper. If you're lucky, you can go and change the machine

1.Do not turn on and charge if water enters.

2.First of all, shake the phone vigorously to throw out as much water as possible, and then use a hair dryer to dry the water First, do not do any operation. Turn it on, or turn it off, etc.

Remove the case and dry the body, such as the water stain on the iPhone 6, open the back cover, and put the iPhone in the rice bag. At the current temperature, the equilibrium humidity of rice stored at home is between 50-70%, which can play a role in drying and slowly absorb moisture. So, put the phone in the rice bag for 24 to 48 hours and then take it out, and the phone can be saved.

Of course, it would be better if there was a desiccant, and the effect would definitely be better than rice.

Use a hair dryer, natural wind drying, if there is dripping water inside, first throw out the water, and then blow some functions are missing after normal start-up, the keys are not working, it may be a hardware failure, it is recommended to contact customer service or bring the invoice to the service site for maintenance.

Don't try to turn it on again if your phone gets into water! Send it to the repair shop as soon as possible and see if there is still a chance to save it.

Motherboard issues.

Tell you what emergency you need to do after the iPhone gets into the water:

1: Don't shake the phone to prevent the water flow inside from causing a larger area of water 2: Turn off the phone immediately, never turn it on.

3: Don't try to dry it with a hair dryer, if the motherboard touches the water, it is easier to cause damage to the motherboard with a hair dryer4: Use a paper towel to dry as much as possible where it can be wiped, and then put the phone in a sealed bag full of rice, and don't move for 48 hours.

After 48 hours, 48 will absorb the water inside, step by step to make sure it is okay or go to the mobile phone store to clean the inside immediately.

iphone6 does not turn on when water enters, and the original form of "seckill maintenance" appears under the microscope