What kind of greenhouse can install a roller shutter machine

Vegetable and flower greenhouses can be installed with roller shutters. It is mainly used for rolling greenhouse straw curtains, and is suitable for greenhouses with a width of about 10m and a height of about 80m, and a length of about 80m.

Greenhouse roller shutter machine is a special machinery for greenhouse, the use of roller shutter machine can roll up straw curtains or thermal insulation quilts in a short time, can improve labor efficiency, reduce labor intensity.

The automatic roller shutter machine is mainly used in greenhouses, which has the characteristics of sturdy and durable, small size, no noise, and good self-locking performance; The biggest advantage is that it is particularly safe to use.

According to the survey, in the process of deep winter production of vegetables in greenhouses, it is only about 5min for every 667m2 greenhouse to manually pull the straw curtain, while the roller shutter machine only takes 5min. When the sun goes down, manual straw curtains need to be used, and the roller shutter machine only takes 3min. This saves labor time per day, while at the same time extending the number of light hours and increasing the photosynthetic products.

Practice has proved that the use of roller shutter machine not only prolongs the light time, increases the photosynthetic products, but more importantly, saves labor time and reduces labor intensity, which is conducive to the large-scale production of greenhouse vegetables.

What's going on with the roller shutter always running to the left? It is caused by the fact that the installation of your roller shutter is not parallel to the greenhouse, and it is recommended to adjust the bearing position of the roller shutter machine. The gables on both sides of the shed are of different heights, that is, the heights of the two mountains are not the same.

What is the problem with the greenhouse roller shutter machine?

Dear, hello, I'm glad to answer for you, what is the problem with the greenhouse roller shutter machine? Answer: (1) The reason why the motor does not rotate or there is a humming sound at the same time after power-on may be a power outage or lack of phase or low voltage, and the line connector switch should be checked (or find an electrician immediately).

2) The motor rotates but the roller shutter machine does not rotate, probably because the V-belt is loose, and the V-belt can be adjusted in time. (3) The machine emits intermittent noise when putting the shed, which may be due to the lack of oil in the brake system, as long as the shed is placed to the end, the noise can be eliminated by injecting clean oil into the brake pads. Pull the curtain down.

5) When the temperature near the brake system is too high, because the lubrication is insufficient, only oil injection is required. (6) If you do not brake when stopping, it is a failure of the brake device, check the brake block, spring and oil injection. (7) The main engine deviates, that is, the grass curtain on both sides of the main engine is inconsistent or the greenhouse is not level, as long as the grass curtain is straightened so that the speed on both sides is consistent.

8) Contact the installer or manufacturer for other faults. (9) When the quilt cannot be rolled to the top or rolled to the top, it cannot be lowered. Reason:

belt slippage; The transmission line voltage is too low; The motor has low power. Exclusion method: tighten the belt; reducing the length of transmission lines or replacing thick wires; The disadvantages are replacing high-power motors.

10) The brakes failed, and the curtain still slipped after the brakes. Cause of failure: brake shoe spring broken or brake shoe does not return; Broken brake pads; The main engine pulley is stuck; There are many oil tables on the brake pads; The brake shoes are badly worn.

Exclusion method: replace brake shoe springs; replacement of brake pads; Remove the main engine pulley and grease the threads; Replace the brake pads or remove the brake pads, use gasoline to clear the oil stains on the brake pads, and then reinstall them and use them; Replace the brake shoes. (11) There is noise when the curtain is placed.

Cause of failure: The gap between the main engine pulley and the brake disc is too large; Broken friction plates; Broken needle roller bearings in brake drums; Exclusion method: remove the belt lock nut and set back 1 6 turns to lock; Replace the friction plates; Replace the bearings.

12) The head of the roller shutter machine is off track when it is rolled and put down. Cause of failure: the angle between the winding rod and the curtain is incorrect; The welding angle between the connecting plate and the support rod is wrong; The shed surface is not level; Exclusion Method:

Adjust the curl dry to keep it perpendicular to the curtain; The connecting plate is always perpendicular when welded with the support rod; Use a spirit level to find the level of the shed. (13) The head scrapes the curtain or the reel rod and cannot be placed to the end. Cause of failure:

The pole is too long or the support rod is too short; Rope hanging town years live reel rod. Exclusion method: according to the standard matching length ratio; Let the rope hang naturally to the reel rod and not be tied.

There are two common types of <> greenhouse roller shutter on the market, one is the back wall fixed roller shutter machine, also known as the rear reel type, the rear pull type or the pull line type greenhouse roller shutter and potato roller machine, which is composed of three parts: the main engine, the roll rod, the column or the bracket, and the other is the shed surface self-propelled type, also called the forward bending and outrigger type greenhouse shutter machine, which is composed of three parts: the main engine, the support rod and the roll rod.

Hello dear, happy to answer your <>

The greenhouse roller shutter system mainly has the following types:1Manual Roller Shutter System:

Senhe adopts manual rotation method for roller blinds, which is suitable for small greenhouses. 2.Motorized roller shutter system:

With the motor drive, the roller shutter operation can be automatically realized through the control system, which is suitable for small and medium-sized greenhouses. 3.Automatic Roller Shutter System:

Using high-sensitivity sensors and control intelligent management technology, it can automatically regulate the temperature to ensure indoor temperature stability and air circulation, which is suitable for large-scale, special environmental protection of modern greenhouses. 4.Hydraulic Roller Shutter System:

The use of pneumatic or hydrodynamic curling roller blinds can achieve the advantages of noiseless, stable, simple and safe, and is suitable for large and medium-sized greenhouses. 5.Movable volume this missing digging curtain system:

The retractable steel frame and rails are used to support the roller shutter, which is suitable for some large greenhouses with special shapes and special requirements. <>

The above greenhouse roller shutter systems have their own scope of application and advantages and disadvantages, and the selection needs to be comprehensively considered according to the actual situation and needs. <>

Summary. The main reason for the frequent occurrence is that the limiter runs over. The limiter of the rolling door machine is generally divided into upper limit and lower limit. Sometimes there is a sudden power outage, and the user can only open and close the door with a hand zipper, or pull the automatic slide wrench to close the door.

What is the problem with the greenhouse roller shutter machine?

We'll be happy to answer your questions.

The main reason for the frequent tease is that the noisy device is overrun. The limiter of the rolling door machine is generally divided into upper limit and lower limit. Sometimes there is a sudden power outage, and the user can only open and close the door with a hand zipper, or pull the automatic slide wrench to close the door.

The problem of solving this kind of stupid imitation situation is very simple, as long as the limit switch is re-fiberized and adjusted back to the effective limit range of the transfer screw, and then the following limit is readjusted, and the lock is firmly nailed to the snail and the peisi.

We hope you find it helpful.