As soon as the Oaks washing machine is turned on, the E2 appears, what s going on?

Maintenance method:1. The general problem is that the water does not enter, or the lid is not covered properly, or the water outlet is blocked;

2. You can check the faucet switch and whether the drain pipe is down or blocked; Whether the lid is opened during drainage or dewatering; Whether the wiring of the door door switch and bias switch of the washing machine is loose and loose; or the door itself is faulty; If you can't find the relevant reasons by yourself, you can only find the after-sales personnel of the washing machine for on-site maintenance.

The washing machine shows the E2 fault reason:

Indicates that the drainage is faulty; Generally, the hatch can only be opened after 2 minutes of turning off or unplugging the power supply.

Maintenance method: 1. It may be that the drain port is stuck by a foreign object such as a coin, and the valve port can not be closed and leaks, overturn the machine, remove the drain pipe to see the drain port, and take out the foreign body.

2. It may also be that the water pipe of the water level sensor of the machine falls off, and the pressure port of the outer barrel leaks.

What is the fault of the washing machine E2?

Automatic washing machine The display of E2 refers to the drainage timeout (if the water is drained for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once.

Washing machine E2 troubleshooting method:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drain pipe is deformed or twisted.

3. Check whether the drain pipe is unblocked and whether there is any foreign object blocking the drain pipe.

Analysis of common causes of washing machine failures and troubleshooting solutions.

1. Washing machine can not be dehydrated troubleshooting.

1.The laundry is in an unbalanced state when washing. Elimination method: You can put a small amount of clothes before washing clothes, and don't stuff too much at once, so as not to cause imbalance during washing. And the effect of dehydration is not good.

2.The safety switch on the top cover of the washing machine is damaged. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch.

3.The washing machine drain system is clogged. Elimination method: Remove the drain filter and clean, rinse the drain with water and remove the debris in the drain valve.

4.The water level switch cannot be reset. Solution: Contact the after-sales point.

5.Due to a faulty motor, the washing machine cannot be dehydrated. Exclusion Method:

You can try opening the back cover of the washing machine and moving the pulley by hand if there is no jamming. If the motor does not rotate when the power is turned on, it means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted.

If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

6.The washing machine cannot be dehydrated due to the damage of the solenoid valve: The washing and dewatering of the automatic washing machine is completed by converting the gear at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

7.The motor plug is loose and the washing machine cannot be dehydrated: Troubleshooting: It should be plugged back in and tied with a strapping wire to prevent it from falling off again.

1. White vinegar: The inner barrel of the washing machine can be cleaned with white vinegar, add water first, then put in white vinegar, soak for 2-3 hours and then start the washing machine. 2. Bleach:

Put water in the washing machine first, add an appropriate amount of bleach, and then start the washing machine. 3. Cleaning agent: Pour the cleaning agent into the washing machine, turn on the washing machine and soak for 1 hour, and finally clean it.

1. Before cleaning the washing machine drain, turn off the power of the washing machine. Then open the small bezel on the back, stuff the coin into the small opening of the baffle, press the door and it opens, this is the washing machine drain.

2. Then, pull out the small water pipe, so that the sewage in the washing machine barrel can be discharged. If the washing machine is damaged and the water inside cannot be drained, it is necessary to drain the water urgently, and then plug the plug and restore the water pipe to its original position.

3. Look at the small round lid in the middle, it is mainly used to accumulate stains, rotate it down and clean it.

4. There is a lot of hair and dirt in this round lid, and if you don't clean it for a long time, it will emit an unpleasant odor. 2 It should be cleaned once every 3 months, otherwise it will affect the cleanliness of the clothes and the service life of the washing machine. After cleaning, tighten the lid tightly, otherwise water will come out when washing clothes.

OaksWorkaround for the washing machine to show e2:

1. Check whether the water inlet valve and water pipe are normal.

It may be that the inlet valve or water pipe is blocked, or dirty, resulting in a failure, and you need to clean and unclean your handwriting to solve the E2 failure.

2. Check if there is no water in the faucet.

It may be that there is no water, or you forgot to turn on the faucet, just turn it on.

3. Check whether the water pressure is too low.

If the water pressure is too low, it will also cause E2 failure, if the water pressure of the tap water itself is small, the water inlet speed will naturally be slower, it is recommended to wait until the water pressure is normal.

4. There may be a foreign object stuck inside the Oaks washing machine.

There may be buttons when washing clothes, or foreign objects are stuck in the washing machine, and the foreign objects can be cleaned up.

5. Check whether the connecting line is broken.

It may be because the connection cable has been bitten off by mice, and it can run normally by contacting the staff to connect it.

6. Check whether the drain pipe is blocked or whether the drain pipe is too high.

If the drain pipe is blocked, or the drain pipe is too large, it will cause an E2 failure, so unblock the drain pipe and adjust the drainage position.

7. The system is temporarily completed and malfunctioned. Jane Friend.

Just shut down and reboot to solve the problem.

8. Instability of power supply voltage.

If you can't solve it personally, it's best to contact the staff for door-to-door testing.

9. Hardware failure.

OaksThe E2 fault is the reason why the drainage does not reach the specified water level within the specified time, and it is necessary to check whether there is any foreign matter in the drainage outlet.

The solution is as follows:

1. You can check whether the upper cover of the washing machine is covered.

2. Check whether the drain is smooth, if the drain is small, it may be that the drain is blocked with foreign bodies, just take it out;

3. Check whether the drainage motor is damaged.

4. Call the after-sales service directly.

Common faults of Oaks washing machines**

The Oaks belt sensitive washing machine shows that the E2 is usually due to draining water for more than 5 minutes, but it is still below the stated water level. The solution is as follows:

1.You can check whether the upper cover of the washing machine is covered first;

2.Check that the drain is clear. If the drain drain is small, the drain may be blocked, and the foreign body can be taken out;

3.Check the drain motor for damage.

Oaks washing machines that do not dehydrate show E3 malfunction.

E3** means the offset of the clothes, that is, when the washing machine enters the rinse, if the clothes are entangled because of knots, causing the clothes to return to a place, so the dry inner barrel shakes very seriously, the washing machine has a safety protection switch, and when the switch is encountered, the computer protects the machine from drying, and sends an e3 alarm**.

Workaround:1Check whether the washing machine is placed flat;

2.Open the lid and adjust the garment.

The E4 failure occurs when the Oaks washing machine is started.

The explanation says that the E4 is a problem with the water level sensor, but sometimes it has no effect after trying, so you might as well check whether there is an error in your operation. Here's how to check it:

Is there a problem with the water level switch? The electronic water level switch uses water pressure to promote the switching state, so that the computer senses the change of water level, thus affecting the effect of the water level sensor.

Summary. 1. The situation that the Oaks washing machine displays E2 is generally caused by draining water for more than 5 minutes and still not reaching the specified water level, you can first check whether the upper cover of the Oaks washing machine is covered, if it is not covered properly, the Oaks washing machine appears E2, and the upper cover can be covered. 2. If the Oaks washing machine shows E2, it may be that there is a foreign object on the wall of the drain outlet, and the drain is blocked.

3. If the Oaks washing machine shows E2, it may be that the drainage motor is damaged, and it can be effectively solved by finding a professional to replace it.

Can you add, I don't quite understand it.

1. The situation that the Oaks washing machine displays E2 is generally caused by the discharge of water for more than 5 minutes and still does not reach the specified water level, you can first check whether the upper cover of the Oaks washing machine is covered, if it is not covered properly, the Oaks washing machine appears E2, and the upper cover can be covered. 2. The situation of E2 displayed by the Oaks washing machine may be a foreign object on the wall of the drain outlet, and the drain outlet is blocked, so take out the foreign body or use a professional detergent to clean and dredge it, and the operation can be completed and the problem can be effectively solved. 3. In the case of the display of Oaks washing machine and the false book E2, it may be that the drainage motor is damaged, and it can be effectively solved by finding a professional to replace it.

The solution of the E2 display of the Oaks washing machine: 1. Check the water inlet valve, whether the water pipe is normal may be that the water inlet valve or water pipe is blocked, or dirty, resulting in a failure, you need to clean and dredge it to solve the E2 fault 2, check whether there is no water in the faucet, it may be that there is no water, or you forgot to turn on the faucet, open it. 3. Check whether the water pressure is too low, the water pressure is too low, and the stupid suspicion will also lead to E2 failure, if the water pressure of the tap water itself is small, the water inlet speed will naturally slow down, it is recommended to wait until the water pressure is normal to use.

4. There may be foreign objects stuck inside the Oaks washing machine, there may be buttons when washing clothes, or foreign objects are stuck in the washing machine, and the foreign objects can be solved by cleaning up the foreign bodies. 5. Check whether the connection line is broken, it may be because the connection line has been bitten off by mice, and contact the staff to connect it that is, the god hand can operate normally. 6. Check whether the drainage pipe is blocked, or whether the drainage pipe is too high, the drainage pipe is blocked, or the drainage pipe is too high, which will lead to E2 failure, dredge the drainage pipe, and adjust the drainage position 7. If the system temporarily fails, you only need to shut down and restart it to solve the fault.

8. The instability of the power supply voltage cannot be solved by individuals, and it is best to contact the staff to come to the door to test. 9. If the hardware failure is troubled according to the above, the Oaks washing machine still has an E2 fault, then to a large extent, the hardware is damaged, please contact the personnel for on-site testing. **：

4008377315 (Click on the number to dial**).

Summary. The washing machine shows that the E2 is faulty, which means that the lid of the washing machine is opened, and the washing machine alarms to inform you.

If this happens, you don't need to repair it.

When the washing process is in progress to drain the water, the lid of the washing machine is opened when the dewatering program is about to be carried out, and the alarm will be informed. When this happens, close the lid of the washing machine.

There is also a situation where after the reservation process of the washing machine is set and started, the lid is opened, and the washing machine will also alarm you.

When this happens, you need to turn off the power of the washing machine, and restarting it will do.

As soon as the Oaks washing machine is turned on, the E2 appears, what's going on?

Hello, I have seen your question and am sorting out the answer, please wait for a while The washing machine shows that the e2 is faulty, which means that the lid of the washing machine is opened, and the washing machine is alarmed. In this case, there is no need to repair it. When the washing process is in progress to drain the water, the lid of the washing machine is opened when the dewatering program is about to be carried out, and the alarm will be informed.

When this happens, close the lid of the washing machine. There is also a situation in the spring, that is, after setting and starting the reservation procedure of the washing machine, the lid is opened, and the washing machine will also call the police to inform you. In this case, you need to turn off the power of the washing machine, and restart it.