How to open the lid of white latex, how to open the lid of a plastic white latex bucket

Prepared tools: iron rods and wooden sticks that can be put into the smart cover holes, but the premise must be hygienic and firm, otherwise it will lead to secondary pollution of the pure water or fall into the pure water after breaking. Step 1:

Regular bottled purified water has a thin film on the smart lid, which professionals call heat shrinkable film. First of all, we need to remove this layer of heat shrinkable film, and the way to remove the shrink film is to tear it directly by hand or find scissors to cut it. As long as you can successfully remove the shrink film on the smart cover, you will be almost successful.

Step 2: After removing the shrink film, you will find that there is a cover on the top of the smart cover, which is called a dust cap by professionals. First of all, we directly remove this dust cover by hand, the standard dust cover is very easy to remove, as long as you find the opening of the cover, it will be easy to remove.

Step 3: After removing the dust cover, you will find that there is a white blockage below, this blockage is called a small blockage by professionals, pay attention to the fact that we do not press the small white race, because we can't put it in the water dispenser after pressing it, because the small blockage is blocked with pure water, if we press it down, we will not be able to deduct it from the water dispenser.

Step 4: The last step is that we first remove the packaging bag outside the pure water bucket, this packaging bag is called the pure water bucket packaging bag in the industry, after removing the packaging bag, our last step is to pick up the pure water bucket and put it on the water dispenser, when we put it, we pay attention to the smart cover must be aimed at the stick in the water dispenser, only after aligning the stick of the water dispenser can we drink normally.

You can also use pliers to open it (it takes some force, not too much.)

Take a flathead screwdriver, turn the circle to pull up the sealing ring, and then unscrew the cover.

White latex is one of the most widely used, largest and oldest water-soluble adhesives, and is a thermoplastic adhesive prepared by polymerization reaction of vinyl acetate monomer under the action of initiator. It can be cured at room temperature, curing fast, high bonding strength, and the adhesive layer has good toughness and durability and is not easy to age.

White latex is a water-soluble adhesive, which is a thermoplastic adhesive prepared by polymerization of vinyl acetate monomer under the action of initiator. Commonly known as white latex or simply PVAC emulsion, the chemical name is polyvinyl acetate adhesive, which is made of acetic acid and ethylene to synthesize vinyl acetate, and titanium dioxide is added (low-grade ones add light calcium, talc, and other powders).A milky white thick liquid formed by polymerization of emulsion.

Tools to come: pliers, flat-edged screwdrivers, pliers from the child bai.

The steps are as follows: 1. Use pliers to remove the plastic white latex bucket lid and mark the dao strip. Clip the mark with pliers and pull it apart firmly.

2. Slowly turn the ring with a hand plier to pull up the sealing ring.

3. Use a flat-edged screwdriver to warp up any part of the sealing ring and pull the plastic white latex bucket lid hard.

4. Finally, remove the plastic white latex bucket lid by hand.

Around the lid of the barrel, there is a ring of seals. Take a flat-edged screwdriver, turn the ring to pull the sealing ring up, and then unscrew the lid to open it.

With a flat screwdriver, make a circle.

Dear, take a flathead screwdriver, turn the circle to rip off the sealing ring, and then unscrew the lid to pay attention to safety when chopping, don't tie your hands How to open the white glue by hand? Pro, take a flathead screwdriver, turn the circle to pull up the sealing ring, and then unscrew the lid to pay attention to safety when chopping, don't prick your hands 1Use pliers to remove the marking strip of the plastic white latex bucket cover, first clamp the marking with pliers, then pull it apart forcefully, and slowly turn the circle with tongs to pull the sealing ring up.

2.Use a flat-edged screwbook to warp up any part of the sealing ring, pull the plastic white latex lid hard, and remove the plastic white latex lid by hand after disturbing the base. White latex can be cured at room temperature, curing fast, high bonding strength, the adhesive layer has good toughness and durability and is not easy to age, white latex is used, according to the different bonding objects, can be appropriately diluted with water.

Prepare a hammer, knife and capper, first use a knife to cut a line on the edge of the latex paint lid, use the knife to warp the edge of the lid, then use the capper to reach into the gap, then use the hammer to hit the tail of the capper, so that the lid can be loosened, and then use the same method to knock on the other parts of the lid, lift the lid, and the lid opens. Here's how:

1. Prepare a hammer, knife and cap lifter.

2. Use a knife to cut a line on the edge of the latex paint lid.

3. Lift the edge of the lid with a knife.

4. Then use the cap lifter to reach into the gap.

5. Then hit the tail of the cap lifter with a hammer.

6. This way you can loosen the lid.

7. Then use the same method to tap the lid on the other positions.

8. Lift the lid.

9. The lid is opened.

1. Insert the end of a small screwdriver into the small hole of the lid of the latex paint bucket first.

2. Then outward, pay attention to safety, and don't hurt your hands.

3. Follow the above steps, repeat the interlayer of the small hole, the hand force should be in place, and the half finger that leaves the edge of the barrel lid is more convenient to open, as shown in the figure below.

4. Then lift the lid carefully and carefully, because there is still a protective ring inside, for future use, don't break it, open it as shown below.

You can see there's a little notch in the edge of the lid, and you can just tear it off along the lid.

First use a knife to cut a line on the edge of the latex paint lid, use the knife to the edge of the lid, then use the cap lifter to reach into the gap, and then use a hammer to hit the tail of the lid lifter, so that the lid can be loosened, and then use the same method to knock the lid elsewhere, lift the lid, and the lid will open.

The latex paint with good applicability will not cause bubbles to overflow and splash during operation, and it will bring smooth walls to the room.

Elastomeric emulsion paint has excellent waterproof function, preventing water from penetrating the wall and damaging the cement, thereby protecting the wall, and has antibacterial function, it has good anti-carbonization, antibacterial, and alkali resistance.