The natural gas meter shows that there is still a lot of gas, but it can t catch fire, what is the r

There is still a lot of gas on the natural gas meter, but it does not ignite, which may be due to the following reasons:

1. Your gas meter.

The battery has no charge. It may be that the gas meter is out of power and the solenoid valve in the meter is closed.

2. The gas meter is broken.

3. The gas pipe is blocked.

4. The regulator is closed.

5. IC card meter overflow protection (I don't know if the gas meter you look at is right, now the general gas meter is a smart meter with a card, the mechanical degree on it is the amount of natural gas that has been used, not the remaining amount, the remaining gas flow needs to press the button on the meter, and the remaining gas will be displayed on the screen).

6. Find personnel from the natural gas company to go to the site for maintenance, and you can generally see it on the pressure regulating box of the building in the community.

It may be: the natural gas meter is faulty, and the natural gas cannot be delivered to the stove normally; The cooktop ignition system is faulty, the cooktop transmission line is blocked, etc.

Most likely, the flint and steel were broken. Because there are cases where the flint and steel will not catch fire if it is broken, you can use a lighter to light it. If it still doesn't work, then it's time to change the gas stove.

This situation can be divided into two kinds, the first, the first problem, it is likely that your furnace is broken, and the other situation is likely that the battery on your gas meter is out of charge, replace the battery, give it a try,

Since it's not a problem of running out of gas, it's likely to be a problem with your air valve switch, and if you don't understand it, you can ask a professional master to fix it.

It could be that the gas stove is malfunctioning, or it is possible that the community has lost the gas.

It means that the gas volume is sufficient, but it may be that the gas stove has no battery, and you can continue to use it if you replace it with another one.

1. The reason why the gas stove cannot catch fire.

1. The high-voltage line is disconnected from the ignition needle.

Solution: Check the high-voltage line break point and reconnect it, and treat it with high-voltage insulating tape, and then use asbestos sleeve for high-temperature protection; If the high-voltage wire is detached from the ignition needle, cut off the head of the high-voltage wire by 5mm and reconnect it to the tail of the ignition needle.

2. The high-voltage output circuit of the pulse igniter is faulty.

Solution: It is very likely that the pulse igniter has poor performance or damage, and it will be replaced directly according to the original model.

3. The distance between the ignition needle and the metal of the burner is too far.

Solution: Re-adjust the distance between the ignition needle and the ignition hole of the burner, generally about 3-6mm.

4. The ignition hole of the stove head corresponds to the ignition needle part that is seriously dirty.

Solution: Use steel wire to penetrate the ignition hole to ensure that the gas is unblocked, and clean the dirt on its surface to ensure that the metal exposure does not affect the ignition function.

Second, how to repair the gas stove if it does not catch fire.

1. Check the gas source to make the gas source sufficient, especially for users who use gas cylinders, if the gas cylinder is insufficient and the pressure is small, this situation will also occur, and the gas cylinder should be replaced in time.

2. Replace the induction needle of the same length of the original model to ensure that the induction needle is well connected with the induction wire.

3. Replace the battery to ensure that the battery is sufficient.

4. Replace the original solenoid valve, and do not replace other types of solenoid valves without permission to avoid potential safety hazards.

5. Replace the pulse ignition assembly according to the original model.

Precautions: The water heater with smoke exhaust pipe will cause accidental flameout due to outdoor strong wind recharge, which can be solved by installing an elbow on the smoke exhaust pipe in the direction of the wind.

My natural gas stove can't catch fire, the gas meter shows that there is gas, and it can discharge sparks, but it doesn't get gas, what's going on? The natural gas stove does not catch fire, which is generally caused by the battery being dead, or the oxidation of the surface of the flashover needle, or the ignition button is faulty.

It may be that the gas stove battery is dead, and replacing the battery in time can solve this problem.

Summary. The reasons and solutions for natural gas showing gas but not igniting are as follows:

If the gas source of natural gas is not opened, first check whether the valve is opened, if it is not opened, just open it and then test the fire.

If the natural gas stove battery has no electricity, it will not ignite, just replace it with a new battery.

The gas pipeline is blocked, so it can't catch fire, as long as the pipeline is dredged.

The natural gas shows gas but does not ignite.

The reasons and solutions for natural gas showing gas but not igniting are as follows:1If the gas source of natural gas is not opened, first check whether the valve is opened, if it is not opened, just open it and then test the fire.

2.If the natural gas stove battery has no electricity, it will not ignite, just replace it with a new battery. 3.

The gas pipeline is blocked, so it can't catch fire, as long as the pipeline is dredged.

Natural gas refers to all gases that exist naturally in nature, including gases formed by various natural processes in the atmosphere, hydrosphere, and lithosphere (including oilfield gas, gas field gas, mud volcanic gas, coalbed methane, and biogenerated gas, etc.).

Do you have any other questions? We'll be happy to continue to answer your questions

The above is all my reply, I hope it can help you and I wish you a happy life

Don't forget to like it! Thanks for your support!

The gas meter shows that there is still a lot of gas, but it is not lit. There could be the following reasons:

1.It doesn't matter if your gas meter battery is charged or not. It may be that the gas meter is out of power, and the solenoid valve in the meter is closed.

2.The gas meter is broken.

3.The gas pipe is clogged.

4.The voltage regulator is turned off.

Card meter overcurrent protection (I don't know if the gas meter you are looking at is right.) Nowadays, the general gas meter is a smart meter with a card. The mechanical degree above them is the amount of natural gas used, not the remainder.

For the residual gas flow, you need to press the button on the meter for the remaining gas volume to be displayed on the screen).

6.Ask the natural gas company personnel to come to the site for repairs. If there is no **, it can generally be seen on the pressure regulating box of the building in the community. (2017-11-03, chaos and chaos).

Troubleshooting steps:

1.Observe whether the spark of the gas stove is soft and weak, and whether the discharge frequency is significantly slower than before. If this is the case, our battery is low, and replacing it with a new one will solve the problem.

2.If the spark sounds crisp and powerful, but it just doesn't ignite, then consider whether the air path is unblocked. It is likely that the nozzle inside the burner is clogged during use. Remove the flame splitter cover, pass a thin wire through the nozzle hole, and then put it back into the flame splitter cover to re-ignite.

3.Check whether the throttle of the gas stove valve body is adjusted too much, resulting in excessive airflow in the fire hole and impacting the electric spark. You can adjust the damper left and right to test whether the test fire is normal.

You've just opened a pipeline of natural gas. This is because there is air in the pipe, you can open the valve for a while, close the valve when you smell of natural gas, and then light it again. Generally, the air that has just been ventilated will not be too easy to use for a few days, and sometimes the fire will be extinguished halfway, so you should be very careful when using it, and wait for a few days to exhaust the air in the pipe.

The gas meter shows that the valve is open, and the status is 2, but it just doesn't ignite.

Hello, it is a pleasure to serve you and give you the following answers:1Reason:

The gas meter shows that the valve is open, but the flame is not open, it may be because the valve of the gas meter is not fully opened, or the valve of the gas meter is damaged, causing the flame to not open. If the gas meter displays status 2, it may be because the power supply of the gas meter is not connected, or the power supply of the gas meter is damaged, resulting in the gas meter not working properly. 2.

Solution: If the valve of the gas meter is not fully opened, you can try turning the valve by hand so that it is fully open so that the fire can be opened. If the valve of the gas meter is damaged, you can try to replace it with a new valve so that the flame can be opened.

If the power to the gas meter is not connected, you can try to check if the power cord is on and make sure that the power cord is connected properly. If the power supply of the gas meter is damaged, you can try to replace it with a new one so that the gas meter can work properly. 3.

Personal tip: When using a gas meter, you should check the valve and power supply of the gas meter regularly to ensure that they are working properly. If a problem is found, it should be dealt with in time to avoid unnecessary losses.

The gas meter shows that the valve cannot be opened because the battery is out of power.

Outside the gas meter, you can only see a digital scroll wheel in the small glass window, and there are also seven digits on the wheel, the first four decimal places are black, and the last three digits are red. The fuel used for people's daily cooking has shifted from firewood, coal and other wasteful and polluting conventional energy sources to clean energy such as natural gas, coal gas, and even electricity.

This is where the gas meter comes into play, with its automatic accumulation function, so that those who use natural gas or piped gas can easily know how much gas they use, so that they can pay according to the cubic meters of gas consumed each month.

If the gas is sufficient and the battery is fine, then it is necessary to analyze the specific situation on a case-by-case basis:

Gas stove ignition maintenance problem, hand press the knob can be normal fire, but as long as you let go of the fire will be extinguished, in this case you need to do the following checks:

1. Whether your operation is correct. Now the electronic ignition gas stove has a flame-out protection device, and it needs to be pressed for 5-10 seconds when ignition, and the induction needle can only be released after it takes effect.

2. Check whether the flame distributor of the gas stove is well placed. If the flame splitter and flame splitter seat have bayonets, the bayonet must be aligned. If the buckle is displaced, it will not only let go of the flame, but also cause the flame separator to burn and deform, and the fire separator will be scrapped after a long time, if so, it may need to be replaced with a new one.

3. Check the thermocouple. It may be that the thermocouple can't eat the flame, so you need to adjust the damper under the gas stove to make the fire bigger, so that the thermocouple can eat the flame and accept the heat and then transfer the heat. If it can't catch fire after adjustment, it may be that the thermocouple is broken, and the temperature cannot be sensed, so the gas will be automatically cut off for protection!

Just helped a neighbor deal with the same situation on Saturday. There is a solenoid valve in the gas meter, which needs to be driven by electricity, usually 4 x 5 batteries. You can check if the battery is charged. I'm talking about magnetic card gas meters, I don't know if your home is of the same type.

This valve is used to control the inflow of gas into your meter. Generally speaking, the outer transparent cover is unscrewed, and the red (or other color) is pulled apart. If it's other models, you have to take a closer look, and they should all be about the same.

In addition, the valve has a signal wire connected to a kitchen unit that automatically shuts down when the unit detects a gas leak.

There are several reasons why the stove won't catch fire:

1. Check whether the ignition electromagnetic rod is normal, if not, check the battery;

2. Your table is an IC card table, whether there is a gas outage due to no balance before, if there is, then insert the recharged card into the IC card slot, so that the balance of the card will be transferred to the table, pull out the card, once the balance is available, the electronic control valve in the gas meter will be automatically opened;

3. Whether there is natural gas in the pipeline, which may be caused by maintenance, emergency repair, riser valve being closed, etc.;

4. The stove is broken.

Use it well, suddenly no gas continues to show gas in the table, just can't hit **, like this case, I think it's mostly because of the consequences of your insufficient gas pressure, under this premise, you can find ways to add a little air pressure in it, so that you can return to normal use, of course, this kind of requires a certain amount of professional technology to operate, if you won't call customer service, let them help you deal with it, after all, many times this equipment requires a certain process, There is also technology that can be operated, and ordinary people will be relatively difficult to operate.

You have to pay attention, sometimes when I was cooking, I poured that water and blocked your gas stove, that and that out of the gas hole, if you have paved a few times, you should clean and clean that Ya for him, he can breathe, and again, are you the battery of your gas stove dead? If the pack battery is dead, it's not good, if it's really these check the access, the road is also open, see if there is that that is blocked in other places? If the road is open, it doesn't work, then you have to go to a professional to show you, maintenance and repair must be this gas, this thing is a dangerous thing, can not be indiscriminate, find a professional to guide and guide, but also to repair for you, but also after the prevention you will understand, will be that used, this use of this gas must be very careful and careful, the danger is very great.