The printer is jammed The machine is Xerox C3300, and the lower part of the machine has been jammed,

There are many reasons for printer jams, and the specific ones are printer paper.

Wrinkled, uneven;Printing paper that is too thin or too much;The paper is too thick or wet;Conveyor roller wear and so on, it is recommended that you first see if the paper is flat, try with 70g or 80g of dry paper, check whether the paper tray is correct, if these are not effective, see if the conveyor roller in the carton is worn, you can try it with your hands, whether there is any debris falling off, if this problem is not, you may have to consider gear transmission.

Problem, see if the carton drive gear is worn, whether the motor is aging, the output torque is not enough, it is recommended to interchange the carton to do a comparative test, such as put a layer of carton on the second layer of carton to see if it can move, put the second layer of carton on a layer of carton to try, etc., if you still have questions, please contact, I am a laser printer.

I understand a little bit about these questions, hopefully.

Check the tray tray and sensor.

Brother!My machine is also faulty, has you fixed it? What's the problem?

It's fixed. It is the crack in the middle of the carton motor transmission gear. Causing the motor gears to slip. Replacement or repair can be normal.

How to solve it?

Same issue with my printer.

Just print three or four copies of the Black Devil.

UU said okay, get the computer.

There are many reasons for paper jams: The most important thing is to see where the paper is jammed, and there are generally the following positions.

1: Paper tray (that is, the paper roller rubs the paper, the printer is showing the paper jam, the reason is that the paper roller is dirty and caused by slipping, and the paper roller can be cleaned).

2: Paper feeding sensor: It is the first sensor through which the paper passes, generally in the upper position of the paper tray below the toner cartridge. (The reason is that there are impurities in the sensor, and it is also OK to clean or blow it off).

3: Flender: This is the most common position of the paper jam, generally because the separating claw on the fuser is stained with solidified toner or other things, resulting in the paper can not be separated when passing there and stuck there, scrape off the unclean things on the separating claw OK.

4: Paper output sensor, the last sensor through which the paper is printed, the reason is the same as "2".

Summary. Hello!This is a problem with your printer paper, that is, your printer paper is too thin or too wet, not dry enough, resulting in a lot of printer paper sticking together, and the printer can only be broken by mistake, that is, it is dirty, and he is easy to add two pieces of paper to suck it together.

The Xerox 3119 printer always starts to set off before the first sheet is finished. It's always jammed.,Is it broken? How to fix it?

Hello!This is a problem with your printer paper, that is, your printer paper is too thin or too wet, not dry enough, resulting in a lot of printer paper sticking together, and the printer can only be broken by mistake, that is, it is dirty, and he is easy to add two pieces of paper to suck it together.

It may be caused by the following reasons: 1. The position of the loaded printing paper is incorrect, which is lower than the arrow sign on the left guide rail inside the printer. 2. The boundary of the inkjet printer is based on the right border, the dot matrix printer is based on the left border, and the laser printer is based on the center.

If the left rail of the printer fits snugly against the left edge of the paper, it will cause the paper to be loose and tilted, and it is easy to twist or multi-page paper when feeding. 3. When the printing paper is curled or folded too severely, it will also occur that multiple pages are fed at one time. If this happens, you can flatten the paper or curl it slightly in the opposite direction a few times to see if that resolves the problem.

4. This situation will also occur if the paper is thick and the position of the adjusting rod does not conform to the type of medium. When printing documents on media of regular thickness, the adjustment lever should be pulled to the "0" position; When printing on envelopes and thicker paper, it should be wrenched to the "+" position. However, some models do not have this adjustment lever.

5. The general printer can only use 60 180g of printing paper, if the printing paper is too thin, such as 40g advertising paper and oily paper, sulfuric acid paper, etc., it is easy to enter multiple pages and jam paper at a time when printing. The solution is to check that the paper meets the printer's requirements, fold the paper into a fan duster to separate the sheets, prevent static electricity from sticking to the paper, and then reload the paper.

Summary. Fuji Xerox S2110 wants to print A3, the computer and printer have been set, but when you press print, an error is prompted, and the bottom of the paper tray 1 is set to A3

Hello dear for your query answer as shown below.

Dear, I hope the above will help you If you are satisfied with me, please give me a thumbs up

Dear, hello, I'm glad to answer for you, Xerox 3119 all-in-one machine put a piece of paper to print normally put more than two sheets of paper on the jam is often jammed 1, check the paper feeding channel, clear the debris of the output path, the front edge of the paper should be just above the metal plate. 2. Check whether the paper roller is worn or the spring is loose, and the pressure is not enough, that is, the paper cannot be fed into the machine. When the paper roller is worn and cannot be replaced for a while, the method of winding rubber bands can be used for emergency treatment.

After winding the rubber band, the friction of the paper rubbing is increased, which can restore the paper feeding to normal. 3. In addition, the installation of the paper tray is not normal, and the paper quality is not good to carry (too thin, too thick, and damp), which will also cause the failure of the paper jam or the inability to take the paper.

1. Check the paper feeding channel and remove the sensitive debris in the output path, and the front edge of the paper should be just above the metal plate. 2. Check whether the paper roller is worn or the spring is loose, and the pressure is not enough, that is, the paper cannot be sent into the machine. When the paper roller is worn and replaced without noise for a while, the method of winding rubber bands can be used for emergency treatment.

After winding the rubber band, the friction of the paper rubbing is increased, and the paper feeding can be restored to normal. 3. In addition, the installation of the paper tray is not normal, and the paper quality is not good (too thin, too thick, and damp), which will also cause the failure of paper jam or paper inability to take up.

Whether the surface of the printing paper is flat. If there is a phenomenon of printer clamping paper, first of all, you should see whether the surface of the printing paper is flat, if the paper is curled or wrinkled, it is best to replace the paper with a smooth and smooth surface, and ensure that the surface of the printing paper can not have similar adhesive attachments.

A printer is one of the output devices of a computer, which is used to print the results of computer processing on the relevant mediator leakage. There are three indicators to measure the quality of a printer: print resolution, print speed, and noise.

There are many types of printers, according to whether the printing element hits the paper, it is divided into a percussive printing side search machine and a non-percussive printer. According to the structure of printed characters, it is divided into full-character printers and dot matrix character printers.

According to the way that the words of the chaotic calendar are formed on the paper, it is divided into serial printers and line printers. According to the technology adopted, it is divided into cylindrical, spherical, inkjet, thermal, laser, electrostatic, magnetic, light-emitting diode and other printers.

History. The printer was co-invented by John Walter and Dave Donald. A device that prints the results of computer calculations or intermediate results on paper in numbers that can be recognized by humans, letters, symbols, and graphics in a prescribed format.

Printers are developing in the direction of light, thin, short, small, low power consumption, high speed and intelligence.

I have actually encountered, the same problem of the machine is also the same problem, in fact, it is the problem of the printer feeding clutch, most of them do not need to be replaced, there is a rubber aging on the clutch and adhesion, can not be reset quickly, resulting in the machine keeps rotating and feeding,。。 The clutch is removed and the cushion rubber on it is scraped off directly, and the problem is solved immediately. . .

Just this small part, the disassembly space is small, use a small plum blossom knife to forcibly disassemble the machine, you will find that there are two plastic cushions on it that are broken, and they are sticky. . .

If the paper wheel is stained with paper ash a lot, it can generally be solved by wiping it with a damp cloth.