How to set up a bridging router, how to set up a bridging wired router

How to set the wireless bridging mode of the wireless router: 1. Confirm the wireless routing parameters of the main router, confirm the wireless signal name, wireless encryption mode, wireless password and wireless channel of the main router. Note:

Before setting up, the wireless channel of the main router needs to be fixed. 2. Set up the secondary router. 1. Modify the wireless parameters and turn on the WDS scan signal.

Connect the computer to the sub-router, log in to the management interface, click Wireless Settings >> Wireless Basic Settings, modify the SSID number to be the same as the main router, fix the channel, check to enable WDS, and click Scan. 2. Select the main router signal. Find the SSID of the primary router in the scan page and click Connect.

Note: If the WDS cannot scan the signal of the primary router, make sure that the wireless function is enabled on the primary router, and try to reduce the distance between the primary and secondary routers. 3. Select the encryption method and enter the wireless password and key type.

Select the encryption method of the main router, enter the wireless password of the main router in the Key field, and click Save when the input is complete. You don't need to restart your router and proceed to the next step of setup. 4. Set the wireless password of the secondary router.

Click Wireless Settings >> Wireless Security Settings, select WPA-PSK WPA2-PSK, set the same wireless password as the main router in PSK Password, and click Save. When the system prompts "You have changed the wireless settings, it will take effect after restarting", click Restart, and when the restart prompt page pops up, click OK and wait for the restart to complete.

1. First, go to the router and click on Advanced Settings.

2. Enter the page and click on the wireless settings on the left.

3. Click on the bridging function inside, and on this page, click Next.

4. Select the primary router you want to bridge.

5. Enter the WiFi password of the router, the bridge is successful, and you can use the WiFi signal at a larger distance.

Bridging method between 2 wired routers: Router B is used as a switch.

1. Router A is set up normally.

2. Router B setting method:

First of all, the WAN port should be vacated, and all the wiring should be connected to the LAN port.

Disable the DHCP service for Route B.

Change the IP address of the LAN port of Route B (not the same as the CIDR block of Router A) to IP address.

Teach you the wired bridging router by hand, and take what you need in two ways, so that the network has no dead ends.

The main router is set up normally, and the secondary router has two connections: 1The LAN port of the primary router is connected to the LAN port of the secondary router, and the other LAN ports of the secondary router can access the Internet.

2.The LAN port of the primary router is connected to the WAN port of the secondary router, and the WAN port in the secondary router is set to automatically obtain IP addresses (DHCP mode), and the DHCP service must be enabled on the primary router.

Let's show you a tutorial on setting up wired connections on multiple wireless routers.

The main router and the secondary router are bridged through wireless WDS, and the wireless terminal can be connected to the secondary router to access the Internet, and automatically switch during the movement to achieve roaming. The specific steps are as follows:

1. Log in to the management interface of the secondary router;

2. Enter the WDS setting interface, click Next in the WDS wireless bridge to start the setting;

3. Scan and connect the signal of the main router, find the signal of the main router, click Select, the router will automatically prompt you to enter the wireless password of the main router, please enter it correctly, and click Next;

4. Set the wireless network name and wireless password of the 5G signal of the secondary router, and click Next.

<>6. Confirm that the configuration information is correct, click Finish, and the setting is complete.

7. Observe the WDS status in the upper right corner, and it is connected, which means that the WDS bridge is successful.

Notes:1. There is no need (and can't) connect network cables between the main and secondary routers;

2. Dual-band routers cannot be bridged with 5G at the same time;

3. Wireless bridging only needs to be set on the secondary router, and the following basic operation instructions are carried out on the secondary router;

Enter the login address of the router in the address bar of the browser. Enter the router management password, and click the right arrow below to log in. After entering the router, click [Advanced Settings] in the upper right corner of the interface. On the current screen, click Wireless Settings.

Modify the IP address of the LAN port. In the network parameters - LAN port setting, modify the IP address to be different from that of router B (to prevent IP address conflict), such as 19162, save, and the router will automatically restart. Enable the WDS feature.

First of all, we connect the router to be installed to the power supply, and connect the network cable to the WAN interface. Then we open the computer browser, enter the "19161" address in the browser search bar and press the Enter key to enter the web page to set up WiFi.

First, log in to the wireless router that needs to be bridged, as shown below, and click on the wireless settings on the left side of the interface. Open the page as shown below and select the option to enable WDS. After checking to enable WDS, the interface below will appear as shown below, click the scan button.

The setup of the bridging router can be done through the router's web interface or through the router's command line interface. In the web interface, you can access the router's settings page by accessing the router's IP address, and then set the bridging mode according to the prompts.

Step 1Plug in the Swift Router and connect the computer to any of the LAN (1 2 3 4) ports of the Snap Router with a network cable. Open the browser on your computer, enter : in the browser, enter the login page, and enter the login password.

1. Set the LAN address of the router to save, it will restart, return to the settings interface after restarting, click "Wireless Settings", select "Basic Settings", and then select "SSID". Select "wpa-psk" as the encryption method, and the password is your favorite.

2. Set the LAN address of the secondary router to prevent conflicts with the main router.

3. Change the starting address of the address pool to ", as long as it does not intersect with the main router.

4. Fill in the IP address of the main router in "Gateway", that is, "Primary and Alternate DNS Server", fill in the address written on the paper before and save and restart the router.