The watch has entered the seawater, is there any salvation?

Normally, there is no help, and in this case, it is very likely that water has entered and affected the operation of his gears, so it is necessary to pay attention to this aspect.

Your watch got into the water, and I think it should be saved. Because most of today's watches are water-resistant, you need to disassemble the case in time and use a hair dryer to dry all the parts inside.

It depends on the quality of your watch, if it is waterproof, then of course it can still be used, if it is not waterproof, he should be separated from the movement and the movement should be water. Well, if it was a battery, it would have broken, and if it was that, if it was that kind of machinery, he might not be accurate.

If the water ingress is serious, quickly take the mobile phone to the mobile phone after-sales service center or mobile phone repair shop and let the professionals help you clean it. If you just put in a little water, you can use an electric fan to dry your phone, or put your phone in a pile of rice for 24 hours.

Hello, if this friend says that your watch is a waterproof watch, then there is no problem, if it is not a waterproof watch, then you can blow it with a hair dryer.

The watch has entered the sea, it should not be able to be used, we can take a look at whether it is damaged inside, there should be nothing wrong.

The watch is flooded, can it still be saved? Can be saved. If the watch is flooded, if it is a mechanical watch, you should go to a watch repair shop to repair it. Wipe the oil sludge, or wipe off the water droplets on the mask.

It is generally difficult to remedy the entry of the watch into the seawater, because the salt and subtraction in the seawater are too high, and it is easy to rust off the parts in the watch.

If the watch is forbidden to be studied, this must be hopeless, because it still has a certain corrosiveness, so the memory inside may be corroded.

The watch fell into the sea, can it be saved? The watch fell into the seawater, hurry up and take it to the watch repair shop to see, so that the masters of the watch repair shop can see if it can be saved?

Generally speaking, if the watch gets into the water, well, it is still useful to dry it in general, but if the seawater is corrosive, it may not be useful!

When the watch goes into the sea, of course, there is the blue one that lifts the watch out, and now the watch is basically waterproof, so it is okay to take it out.

It is necessary to do the overall maintenance, because it is still salt water, which has a certain corrosiveness to metals, etc., and it is recommended to do the overall maintenance of the watch.

The watch has entered the sea, is there any salvation, this can also be saved, you give him an empty space, electric brother, oh, blow it with a hair dryer, it may be good.

It is best to go to the professional after-sales maintenance department to see if it can be repaired, and it is not recommended to disassemble the watch by yourself.

I just checked for you, this can be remedied, you can go and fix it.

Such a professional question, I think you should take it to the repair shop to ask.

Hello! If your friend's watch is broken and can be repaired, you can take it directly to the repair point for repair.

Hello dear, method 1: What to do after the watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb (about 15 cm), bake for about 30 minutes, and the water vapor in the watch can be eliminated. Method 2:

Put the watch in a rice bowl and bury it deep in the dried rice for a while, and if you are fast, you can see obvious results in one night. Method 3: What should I do if water enters the watch?

You can also use a granular substance called silicone to put it in an airtight container with the watch that has been flooded, and after a few hours, remove the watch and the water will disappear. Method 4: Take a hair dryer to dry, and then apply a layer of transparent nail polish to avoid impurities from entering and prevent rust.

Method 5: If there is water vapor in the watch, you can put the watch face inward and the bottom case outward, and wear it on the wrist to eliminate the water vapor in two hours. If there is too much water in the watch, the case must be opened and scrubbed.

If you are not sure to deal with it yourself, you should send it for repair in time.

Summary. Hello, I'm glad to be able to answer the question of how to deal with water in your watch.

1. If the watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb about 15 cm, bake for about 30 minutes, and the water vapor in the watch can be moisture. Do not bake the watch close to the fire, so as not to deform the watch by heat.

My watch got water.

Hello, very high imitation Pai Xing can answer for you the treatment of the watch into the water.

1. If the watch is soaked in water, you can use several layers of toilet paper or flannel that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb about 15 cm, bake for about 30 minutes, and the water vapor in the watch can be moisture. Do not bake the watch close to the fire, so as not to slow down the deformation of the watch.

Method. Second, the surface is facing inward, the bottom is facing outward, and the reverse roll is worn on the wrist, and the moisture can be eliminated after more than two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method. 3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will all disappear. This method is simple and does not cause any damage to the accuracy and life of the watch.

The silica gel after the hail oak has been absorbed many times, can be dried for several hours at 120 years in the morning, the water absorption capacity is renewable, and it can be used again and again.

If water gets into the watch, immediate measures need to be taken to prevent further damage to the movement. Here are some ways to deal with it:

Stop using the watch immediately: Immediately remove the watch, stop using it, and pull out the crown as soon as you notice water entering the watch to avoid further damage.

Keep the watch in a dry and ventilated place: Place the watch in a ventilated and dry place, such as a balcony or vent, to allow the moisture to evaporate naturally, but do not place it in direct sunlight to avoid damaging the dial and band.

Use a hair dryer: If the watch has a lot of water ingress and needs to evaporate water faster, you can use a hair dryer. However, it is important to note that you do not spray the hair dryer directly at the watch to avoid overheating and damage to the watch.

It is recommended to set the hair dryer to a low temperature and keep it away from the watch, and blow hot air around the watch to speed up the evaporation of moisture.

Send it to a professional repair shop: If the water ingress of the watch is more serious, it is best to send it to a professional watch repair shop for repair, so as to avoid moisture damage to the movement and cause more serious damage.

When water enters the watch, it is necessary to take measures as soon as possible to prevent damage to the internal parts of the watch caused by moisture. Here are some workarounds:

2.Dry the watch: Dry the watch with an absorbent item (such as a paper towel, towel, etc.), and untie the strap to wipe the inside of the watch as much water as possible.

3.Store in a dry place: Keep the watch in a dry and ventilated room, not directly exposed to sunlight or near a strong heat source such as a heater or hair dryer.

4.Send it to a professional repair station: If the watch is not yet in working properly, it is recommended to send it to a professional watch repair station for inspection and repair.

It is important to note that it is not recommended to disassemble or repair the watch after it has been flooded, so as not to damage the watch parts and lead to more serious consequences.

If water enters the watch, it is recommended to remove the watch immediately, open the finger cap, and dry the internal moisture. If the watch is water-resistant, you can gently press the knob to release moisture inside. If the watch is not waterproof, it should be immediately sent to a professional watch repair shop for cleaning and repair, so that water does not enter the movement and cause damage.

Before sending the watch to Changcou repair shop, you can use a water towels to dry the external moisture, but do not expose the watch to sunlight or use heating tools such as a hair dryer to dry it, as this will aggravate the internal damage.

The first step is to open the crown and pull it to the outermost setting, place the needle disc facing up, and heat it from the bottom to the top with the hot air setting of the hair dryer until the glass fogs up.

In the second step, press the crown back into the first gear for the locking model, without locking it. If it is not locked, put the crown handle in the second gear or do not move, and send the watch wearing hand to the nearest watch shop to let the master open the lid and dry the water vapor. Be sure to wear it on your hands! Don't put it in your bag!

The third step is to have the watch repaired by the master or sent back to the brand's special repair point at the counter. Watches that normally enter water and are sent for repair within two days will not show rust and broken parts, except for quartz watches.

The above three steps are suitable for most watches, and some flip-up or multi-faceted watches can also be dried and repaired when smiling.

Use a hair dryer to dry the water as soon as possible.

Looking for a watch shop? Or just change a watch.

Take it to a place that specializes in repairing watches, or take it to a place where you bought a watch.

The first method: bake with an incandescent lamp Wrap the watch with water and wrap it in several layers of paper towels, then place it at 15 cm of a 40-watt incandescent lamp, bake for 5 minutes, and the water vapor in the watch can be evaporated. Remember not to bake for too long, and for watches with leather straps, the strap should be removed first.

The second method: put it together with the desiccant.

The water absorption effect of desiccant is much better than that of rice, put the watch and desiccant together, wrap it in plastic wrap, wait for 24 hours, and it will not cause dust pollution.

The third method: put it in rice.

Rice has a good water absorption effect, and every family has rice, and it is easy to use. After 24 hours of placing the watch in the rice, most of the water is absorbed. Finally, take out the watch and gently wipe off the rice dust.

The fourth method: reverse the watch.

In order not to disassemble the watch, you can wear the watch upside down, wear the watch glass on your arm, and discharge the water vapor in the watch little by little.

Method 1: Put it in a rice jar and bury it deep in the dried rice for a period of time, if you are fast, you can see obvious results in one night.

Method 2: Put the watch on the TV, table or other places in the room before going to bed at night, but do not do it, it must be an indoor with air circulation (it is best not to open the window), because the humidity in the room will be relatively low at night, and it is easy to evaporate the water!

Method 3; It is best to keep the watch sealed with a granular dry substance, and after a few hours, remove the watch to eliminate the standing water in the watch.

Method 4: Wear it in reverse, that is, stick the word **.

Method 5: If water enters the case, you can use a granular substance called silicone to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Method 6: If the mechanical watch stops rotating, it may have rusted, it is best to send it for repair, you can also disassemble the watch core, soak it in gasoline after blowing, if it is an electronic watch, maybe the circuit board has been broken, you can disassemble and place, wait for the inside of the watch to dry through, see if it can be moved, if not, change the battery to try, and then not, it can only be sent for repair or scrapped.

ps: My watch is always flooded, so I put it on my desk, and there will be no water in a day!!

bs those plagiarized.

Hope it works for you.

Give it to me, it's all my own fight, I'm tired to death!!

It's clear that your watch is a quartz watch.

First of all, you need to remove the battery as soon as possible and then dry the water of the movement, and then place the movement on a hot plate at about 60 degrees (about 10 minutes) to make sure that the water is completely evaporated, and then install the battery on the movement (generally this is no problem).

If it still doesn't work, it is possible that the battery has leaked (if it is just that the battery is out of power and the battery can be replaced), or it is possible that the circuit board has burned out (the circuit board has been short-circuited and burned out and you will have to replace the movement); It is recommended that you find a professional master to help you test and determine.

Now an ordinary watch should also be waterproof, buy a watch or find a professional to help you buy.

What kind of watch is it?

You leave it for a few days, and some watches are designed to be OK when the water dries.

Water ingress in an electronic watch can cause a short circuit between the electronic movement and the circuit board.

If water enters the mechanical watch, the movement will rust, unless the case is disassembled and lubricated.

Another situation is that the resistance of the movement increases after the watch enters the water, and it cannot move.

Water ingress into the watch will generally cause damage to the various movements in the watch, and the watch that is generally not waterproof will become inaccurate after a short time, and then stop working completely, at this time the watch is basically scrapped, and it is generally not repaired.

Regardless of the watch, as soon as water gets inside, it will have an effect on the movement. Maybe you have to change the movement or something. There are expensive and cheap movements, and it's hard to talk about. It's best to let the watch repairer see if there is any salvation.

It is recommended that you buy a waterproof watch, I hope it can help you.

If the watch falls into water: 1You can give him a screwdriver to throw away the surface after 2You can also find a maintenance master to open it for him, take the paper and dry the water inside3Find the charging port and blow into it 4Take a hair dryer and blow it.