How to make the glass glue fail, how to use the glass glue correctly

Renovation is a complex process that not only covers a lot of items, but also a lot of details. Playing glass glue during decoration is also a technical job, although it is a small detail, but it is also a technical work. The following is the method of playing glass glue shared by the master, which is very practical.

The first thing to note is that glass glue must be bought in a regular brand store, so that it will not become moldy in the future.

Here's how to make glass glue::

1. The first step is to use a lighter to bake the nozzle of the glass glue soft and make it flat.

2. The correct method is to cut the nozzle at an angle of 45 degrees, and then align it with the position of the glass glue.

3. According to the above method, put the glass glue flat into the glue gun, press the switch, and push it up from the bottom in turn.

4. When hitting glass glue, it must be molded at one time, and there can be no pause in the middle.

The above method can not only increase the glue discharge area, but also reduce the amount of glue. When playing glass glue, the emphasis is on one go, and there is also scraping while playing, so as to avoid the problem that the glass glue cannot be connected.

The following summarizes the method of playing glass glue, and I hope it can be applied in the decoration in the future.

The first is to hit the position of glass glue, which must be cleaned first;

secondly, it is the position of the glue, as well as the angle of the glue mouth;

Finally, when playing glass glue, speed is a very important factor, and you can't stop in the middle. When the large glass glue is used, it should be noted that the strength of the glue and the speed of the dragging gun should be matched well, which is very important.

Scrape the glass glue with a razor!

The use of glass glue is as follows:1. Do a good job of cleaning: Before gluing the glass glue, it is necessary to remove dirt, dust and other dirt from the surface of the joint.

Clean the surfaces of the two objects that need to be glued and keep them dry. The interface surface is then covered with plastic tape to ensure a perfect seal and neat lines.

2. Specific bonding: cut the nozzle, install the needle-nose tube, and then cut at a 45-degree angle according to the size of the joint. Finally, a caulking gun is installed, squeezing the rubber at a 45-degree angle along the gap to ensure that the rubber and the substrate surface are in close contact.

When the seam width is greater than 15 mm, the glue must be applied repeatedly. After gluing, trim the surface with a knife to remove excess glue, and then remove the tape. If any stains can be removed with a damp cloth.

3. Glass glue pasting time and curing timeThe curing process of glass glue develops from the surface inward. Silica gel with different properties has different surface drying and curing times. Therefore, if the surface is to be repaired, it must be done before the glass glue dries.

In the first step, the glass glue is preheated for 15 minutes (only for some Henkel products);

In the second step, the new glass is thoroughly cleaned with Henkel FL cleaner;

In the third step, apply primer to clean glass for 8517h and dry for 10 minutes;

The fourth step is to remove the window trim;

The fifth step is to cut the glass glue of the original car and remove the old glass;

The sixth step is to flatten the residual glue on the frame, if these residual glue is the original glue, it will become a good bottom layer of Henkel glass glue, because Henkel after-sales glass glue and the original glue have good compatibility, and the bottom layer does not need to be coated with primer to achieve a good bonding effect;

Seventh, if the metal or paint is exposed on the frame, these parts need to be primed for 8517h;

In the eighth step, cut the nozzle as high as required;

The ninth step is to apply sizing with a triangular cross-section;

Step 10: Install the glass in the correct position before the Henkel glass glue surface dries.

The eleventh step is to install the window trim and conduct a water leakage test;

The twelfth step, according to different rubber grades, wait for the corresponding safe driving time, and then drive normally.

How to deal with glue on the glass: heat it with a hot towel and then pull it off with a knife; use detergents; Use of industrial alcohol.

1. Hot towels

First, use a hot towel to heat the glued part of the glass, use transparent glue to stick it tightly while the glue is still hot, and use a small blade to stick the single-sided tape on the glue head and slowly pull it down together.

2. Detergent

Use a toothbrush or pot yarn with a cloth dipped in detergent and wipe it in a circular motion along the glass, while placing a rag under the toothbrush to prevent sewage from dripping.

3. Industrial alcohol

Wipe the glue on the glass with organic solvents or industrial alcohol, or highly concentrated liquor. Be careful to wipe with a rag and do not touch it directly with your hands.

Ways to keep the glass clean:

Tip 1: Beer white vinegar

Prepare a bucket of clean water, then add a small half bottle of white vinegar, pour in a can of beer, stir it to mix well, and then spray it on the glass and scrub the glass wheel hole with a clean rag. Because white vinegar is effective at cleaning dirt and oil stains, beer forms a protective film to prevent dust from sticking to the glass, which stays clean and shiny for longer.

Tip 2: White vinegar, dish soap, laundry detergent

In addition to white vinegar, it can be used with beer, and it is also a good choice with dish soap. Preparation: Prepare a container and pour some white vinegar into the container.

You can pour a little more white vinegar to remove stubborn stains from the glass, and finally pour some dish soap into the container. When cleaning the glass, spray some homemade detergent and let it sit for a minute to soften the stubborn stains on the glass.

Glass stick-to-glue treatment method: hand cream, alcohol, nail polish remover removal, hair dryer hot blowing, eraser wipe.

1. Hand cream

I believe that every girl has hand cream, in addition to being able to moisturize our **, it can also clean the glass, just squeeze a little in the place where there is glue, and then slowly rub it with your fingers, so that the glue on the glass can be completely cleaned.

2. Alcohol

Apply alcohol to the area where the glue is present, let it sit for a while, and then wipe it with a paper towel. If the range of glue is relatively large, you can directly wipe it with a rag dipped in alcohol, which is simple and very convenient. It can also be cleaned with acetone, which works in the same way as alcohol, but it cleans faster and has more cleaning power.

3. Nail polish remover

Not only does it clean the nails, but it also removes glue from the glass. The judgment is only to apply it to the parts with glue, and then slowly wipe the loss, and the nail remover to clean the glue does not need to pick expensive, and the ordinary one can achieve the cleaning effect.

4. Hot blowing with a hair dryer

You can take out the hair dryer, adjust it to the hot air, then blow it on the glue on the glass, and finally scrape it off with a scraper.

5. Eraser

The eraser used by students is very versatile, and it can also remove glue, just wipe it on the glue area, but this method is not particularly effective.

The places where glass glue is generally used in home decoration are: the dumb place on the back of the wood line, sanitary ware, toilet, makeup mirror in the bathroom, the gap between the sink and the wall, etc., these places should use Changlu glass glue with different properties. The adhesive of neutral glass adhesive is relatively weak, and it is generally used on the back of the bathroom mirror where there is no strong adhesion.

Neutral glass glue is used more in home decoration, mainly because it does not corrode objects, while acid glass glue is generally used in the dumb part of the back of the wood line, and the adhesion is very strong. Another important thing to use is to prevent mildew.

For example, many glass glue are used in the bathroom, and the bathroom is already very humid and easy to mold, so the glass glue must be mildew-proof. Generally, the glass glue bottle will be explained, be sure to see it.