Where is the 15 year old BYD S72 0T engine crankshaft position sensing point

The following are the recommendations of Huangjiang Shihao Auto Company, 1Use lubricants of the appropriate quality grade. The selection standard shall not be lower than the requirements specified by the manufacturer.

2.Change the oil and filter regularly. Lubricants of any quality grade will change in oil quality during use.

After a certain mileage, the performance deteriorates, which can cause various problems for the engine. In order to avoid the occurrence of failures, the oil should be changed regularly in combination with the use conditions, and the oil volume should be moderate (generally the upper limit of the oil scale is better).

3.Keep the crankcase well ventilated. Most gasoline engines are now fitted with PCV valves (crankcase forced ventilation) to ventilate the engine, but contaminants from the blow-by can deposit around the PCV valves and can clog the valves.

If the PCV valve is blocked, the pollutant gas will flow into the air filter in reverse, contaminating the filter element, reducing the filtration capacity, resulting in increased fuel consumption, increased engine wear, and even damage to the engine. Therefore, it is necessary to maintain the PCV regularly to remove contaminants around the PCV valve.

4.Clean the crankcase regularly. During the operation of the engine, sludge will be formed due to various changes.

When the amount is small, it is suspended in the oil, and when the amount is large, it is precipitated from the oil, blocking the filter and oil holes, causing difficulty in engine lubrication and causing wear. Therefore, we need to go to the 4S shop regularly to clean the crankcase and keep the inside of the engine clean.

5.Clean the fuel system regularly. In the process of fuel supply to the combustion chamber through the oil circuit, it will inevitably form gum and carbon deposits, which will make the fuel atomize poorly, causing performance problems such as engine wheezing, detonation, unstable idling, and poor acceleration.

6.Maintain the tank regularly. Rust and fouling of the engine water tank are the most common problems. Rust and scale can restrict the flow of coolant through the cooling system, reduce heat dissipation, and cause engine overheating or even engine damage.

Summary. Hello dear. The installation steps of the crankshaft timing signal panel of the BYD machine are as follows:

1. First of all, the special tools for signal disk calibration. 2. Find the small round hole on the crankshaft signal panel. 3. When the round hole on the signal disc is installed on the roulette wheel, it should be paired with the small round hole on the roulette wheel.

4. There are also three small holes in the crankshaft housing. 5. When installed on the roulette, it should also correspond to the three holes on the roulette. 6. After that, the shell is loaded into the special tool for the calibration of the crankshaft signal disk.

Dear, you are aggressive. The installation steps of the crankshaft timing signal panel of the BYD machine are as follows: 1. First of all, the special tool for calibrating the signal panel is accurate.

2. Find the small round hole on the crankshaft signal panel. 3. When the circular celery hole on the Xinkong Burning Talk Plate is installed on the roulette wheel, it should be paired with the small round hole on the roulette wheel. 4. There are also three small holes in the crankshaft housing.

5. When installed on the roulette, it should also correspond to the three holes on the roulette. 6. After that, the shell is loaded into the special tool for the calibration of the crankshaft signal disk.

Is this installation method yes?

Dear, yes. It's a little hard to understand.

Dear, then you are like this: 1. According to the mark on the crankshaft timing pulley, the position of the piston top dead center of the 1 cylinder is generally required; 2. The mark on the timing pulley of the installation of the convex and vertical hidden axle is aligned with the camshaft, and the position of the double camshaft is aligned with the position of the two camshafts; 3. Install the timing belt chain.

Summary. In this case, the main thing is to first align the front timing, then turn to the fulcrum position on the cylinder, and finally install the signal gear ring, the timing is not installed, and the signal gear ring cannot be installed, so first use a tool to jam the timing there.

This is mainly the first need to align the front timing, and then turn to the fulcrum position on a cylinder, and finally install the signal gear ring, the timing is not installed, and the signal gear ring is not able to be installed.

The body control module is located in the hall below the main driver's seat and is a square box. Under the middle of the dashboard, it can be seen by removing the passenger seat trim.

The BYD F0 is equipped with BYD D371QA all-aluminum high-performance and environmentally friendly engine, which is made of all-aluminum material. The weight of the engine is significantly reduced compared to cast iron, which improves the fuel-saving performance of the vehicle. The German Bosch fuel-saving control system is adopted, and the rising power is more than 50 kW, which is much higher than other cars of the same displacement and close to many engines.

At the same time, the emissions of this Yanhuiyin engine have reached the Euro IV standard, and Bishi has won the title of "Fuel-saving Champion" in the fuel-saving evaluation of the model of the China Automobile Association. It has been rated as one of the top ten engines in the BorgWarner Cup "China Heart", and its parameters are comparable to those of Toyota and Mazda. BYD F0 is positioned as a cheap mass consumption model, facing both family users and individuals, both young consumers and mature users.

BYD F0's so-called "lowest price" is not a market operation, and the ideal it wants to express is the most important. Small cheap cars have once again become a new trend in the international automotive industry, and many large companies, including BMW and General Motors, have been **, and have plans to launch new cheap small cars. Consumers in the global market are gradually turning to low-emission, energy-efficient, environmentally friendly and fashionable models.

And BYD's approach is exactly in line with this trend. More importantly, it is completely in line with BYD's own development.

Millions of car purchase subsidies.

The speed sensor is mounted on a tachometer bracket and is radially aligned with the gears. Generally near the output shaft. The installation gap is in between. The signal output cable of the sensor is a four-core shielded wire, red 24V, black COM, yellow, signal output 1, green signal output 2.

The speed sensor is a new type of speed sensor with a magnetoresistor as the sensing element. The core component is a magnetistor as the detection element, and then through a new signal processing circuit to reduce noise and improve the function. By comparing the output waveform with other types of tooth speed sensors, the error of the measured speed is very small and the linearity characteristics are very consistent.

The sensing object is magnetic materials or magnetically permeable materials, such as magnets, iron, and electrical steel. When the magnetic or magnetic permeable material with a bulge (or depression) on the measured body rotates with the rotation of the measured object, the sensor outputs a pulse signal related to the rotation frequency to achieve the purpose of velocity or displacement detection.

There is a Hall semiconductor chip in the magnetic field, through which a constant current i passes from A to B. Under the action of the Lorentz force, the flow of electrons from i is shifted to one side as it passes through the Hall semiconductor, causing the chip to create a potential difference in the direction of the cd, which is known as the Hall voltage.

Photo by Tang Yanyan) M5 Xpeng P7 AION V Trumpchi GS8 Xpeng P5 Ideal One @2019

It is installed on the fixed bracket of the crankshaft and cylinder block, which can not only support and lubricate the crankshaft, but also have a positioning protrusion on each bearing, so as to play the role of axial positioning of the crankshaft. Then, its installation steps can be said to be relatively simple, as long as the positioning protrusion is snapped into the positioning groove in the cylinder block.

BYD will unveil the BYD S7, an all-new SUV model at the 2013 Shanghai Motor Show. As the name suggests, the model will be positioned higher than the existing S6 model and is expected to be powered by an engine.

It is reported that the car is expected to be officially launched in November 2014 at the earliest. From the point of view of appearance, **BYD S7 does not have too much similarity with the current BYD S6 in terms of design. The BYD S7 adopts a new front face design, with a U-shaped front grille integrated with the headlights, and a large chrome grille design that is more stylish.

In addition, LED daytime running lights with linear light sources will be added to the headlights.

Compared with the current criticism of the appearance of the BYD S6, the S7 is more original in design and more mature. The BYD S7 is an all-new SUV model developed based on the S6. The model platform remains the same, but the styling design has been greatly upgraded.

The grille on the front face of the S7 is similar to that of the BYD Qin, and it should also be the prototype of the next BYD family.

Millions of car purchase subsidies.