BYD S62 0 engine for 3 0 engine OK

1.Each car has an ID card, which is a VIN number (a string of alphanumeric numbers in the lower left corner of the front windshield).

Correspondingly, the engine of each car also has an engine number (on the engine block), and these numbers have been set when the vehicle leaves the factory.

When you buy a car, you have to copy these two numbers on your driving license, registration certificate or something.

So it can't be exchanged.

2.And the engine was changed, and the drivetrain in front had to be replaced.

3.Before each car is launched, the engine and the whole vehicle are matched. If you switch to a different engine halfway through.

It definitely has an impact on the reliability of the car. It's like if your heart is and you want to change it, your body will definitely reject it.

It is often necessary to take medicine to weaken this rejection, but not **.

You can buy a better car.

It shouldn't be good, it's useless to just change the other parts of the engine. And after changing the engine, aren't your driving license and vehicle registration certificate useless?

Summary. Dear is happy to answer for you: 2013 BYD S6 is the engine, the maximum power of the engine is 160 horsepower, the peak torque is 215 Nm, the engine model is 4G69S4N, equipped with a variable valve timing system, so that the output of the engine at different speeds is more stable, I hope mine can help you <>

<> 2013 BYD S6 what engine.

Dear kiss is happy to answer for you: 2013 BYD S6 is the engine, the maximum engine power of 160 horsepower, peak torque of 215 Nm, the engine model is 4G69S4N, equipped with a wide variable valve timing system, so that the output of the engine at different speeds is more stable, I hope mine can help you <>

<> the expansion to you is: Precautions for engine use: 1. The fuel must be clean.

There are many impurities in the fuel Li Shen, which will accelerate the wear and tear of the electric fuel pump and reduce the service life of the fuel pump. The engine has high requirements for the quality and grade of fuel, and the requirements for EFI engines are even higher. 3.

Refuel in a timely manner. When the fuel in the tank is insufficient, the fuel should be replenished in time, 4When the ignition switch is turned on, do not disconnect the electrical equipment circuit.

5.Regularly clean the fuel system and air intake system. If the fuel system is not clean, it will cause the oil circuit to be unobstructed or even blocked, the valve is not closed tightly, and the fuel injection atomization is poor, which directly affects the normal operation of the engine.

Summary. Hello, happy to answer your <>

BYD engine timing: first the piston is located at the upper dead center of the compression stroke, the camshaft timing mark is aligned with the marking on the timing belt cover, and then the timing belt is installed on the crankshaft sprocket, and then through the left side to the right side, the letters on the new belt can be read from the back of the engine. Finally, turn the crankshaft clockwise about 2 times until the yellow mark aligns with the 0 mark on the lower timing belt cover.

BYD engine timing.

Hello, happy to answer your <>

BYD engine timing: first of all, the piston is located at the upper dead center of the compression stroke, the timing mark of the convex buried lead axle is aligned with the mark on the timing belt cover, and then the timing belt is installed on the crankshaft sprocket, and then from the left to the right, the letters on the new belt can be read from the back of the engine. Finally, turn the crankshaft clockwise about 2 times until the yellow mark aligns with the 0 mark on the lower timing belt cover.

Kiss <>

Expand: Precautions when timing belts: 1

There are signs of a faulty timing belt: engine weakness, abnormal noise, failure to start or prolonged starting. Therefore, the owner needs to consider this part when imitating Zheng Jue has the above phenomenon, of course, not only this, but also other parts.

2.The cylinder reaches the top dead center. Then assemble other gears except camshaft gears, and see that there is a mark on the body, so that the standard ode of the camshaft gear coincides with this mark.

After that, turn the engine to make it about 22 degrees before the top dead center, adjust the fuel injection pump to make it in a state of just out of the oil in a cylinder, lock the screws, and you're done.

Summary. Hello: 1, BYD S6, displacement manual transmission, engine 5 gear 3000 rpm speed is about 100-110, this is the normal speed and speed performance.

2. If the speed can go up, the speed can't go up, the engine only roars and has no power output, such as the speed of 4000 rpm 80 yards, it is caused by the clutch slipping, and the three-piece set of clutch needs to be disassembled and replaced by the gearbox to solve the problem. 3. S6 is a car with a large weight, slower speed, higher fuel consumption, and a fuel consumption of about 10 liters per 100 kilometers, but her girder structure is relatively thick and safe. I hope mine can help dear.

Hello: 1, BYD S6, displacement manual hunger gear, engine 5 gear 3000 rpm speed is about 100-110, this is the normal speed and speed performance. Shoumin 2, if the speed can go up, the speed can't go up, the engine only roars and has no power output, such as the speed of 4000 rpm 80 yards, it is caused by the slippage of the rotten celery binder, and the three-piece set of clutch needs to be disassembled and replaced by the gearbox to solve the problem.

3. S6 is a car with a large weight, slower speed, higher fuel consumption, and a fuel consumption of about 10 liters per 100 kilometers, but her girder structure is relatively thick and safe. I hope mine can help dear.

My 3000 rpm to 120 is fine.

You should be, this can be like this, the naturally aspirated engine, the speed is relatively high, the speed is relatively slow.

The 2012 model has made some adjustments to the 2011 model, optimizing the model configuration, such as the addition of a manual transmission, and at the same time, the automatic transmission model has been changed from the current AT to a dual-clutch transmission.

2012 BYD S6 power information "see attached picture".

byd483qb(

byd488qa(

BYD supplied two engines for the S6, one developed and one from Mitsubishi.

The model codenamed BYD483QB is independently developed by BYD, with variable air intake technology, maximum power of 103kW 6000rpm, 1 peak torque of 186Nm 4000-4500rpm, and the parameters are at the upstream level in the independent brand.

The model uses the Aerospace Mitsubishi 4G69 engine with MIVEC variable valve timing system, with a maximum power of 118kW 5000-6000rpm and a peak torque of 215Nm at 3500-4500rpm.

This doesn't have to be, it depends on your use and the quality of the car. The normal overhaul is around 18 km. If you don't maintain it in time, it will be repaired in about 10 kilometers or so.