How to remove the upper pulley sliding door? 50

Tear down from the top of the door and push the door sliding.

The order of fastening structure is from top to bottom, the upper door frame is disassembled, the fastening nut is found on the door, the upper one is dismantled, and then the door is brought out, and the pulley below can be taken out to replace, pay attention to the wood door is easy to bump and damage, slow down when dismantling, and knock on the demolition with a rubber hammer.

1.Remove the hanging rail screws on both sides of the upper end of the door, pull out the hanging rails to both sides, (there is a card slot at the upper end of the door, and the hanging rail is stuck in the card slot) The door is removed.

2.The two doors are dismantled in the same way. When installing the door, pay attention to the fixed wheel on the ground to clamp into the slot under the door, and then install the slide rail into the card slot at the upper end of the door and screw it.

Remove the positioning pin first, and then push the door to the top, remove the slide Rose, then push the door away, pad, remove the slide Rose at the other end, and the door can be taken down.

Sliding door, this sliding door, you can just get that professional to come and remove it, and they will remove it for you.

Just remove the fixing screws and you're good to go.

Drawing of the sliding door of the upper chuteTools: sliding doors, shovels.

1. There is an insert of a hanging wheel above each of the two sides of the door, and the insert and the side of the door are flat, which is the key.

2. After installation, sometimes it may be pasted during decoration for the sake of beauty, and the decorative skin on the upper corner of the side should be scraped off a little.

3. You can touch it with your hands and feel the seams, so that it can be disassembled.

4. If it is concealed, first remove one side, lift the door, and then turn the door out while pulling the door out.

5. Until the angle of pushing the door in general, it is completed.

1. One person lifts a door so that it is not affected by the top pulley, and one person uses a slender stick such as a screwdriver to gently move the top pulley of the lifted door outward and get out of the position of the door.

2. The door can be lowered when the pulley is separated from the sliding door, and the door without the pulley cannot slide freely.

3. Lift the door again and drag the lower part of it outward, the door needs to be installed back after being removed, and the steps are the opposite of the steps removed.

4. Pay attention to one point, don't push the pulley back to the iron groove at the top of the door, and you're done.

Dear, I'm glad to answer for you: how to disassemble the upper pulley sliding door is as follows: 1. If you want to disassemble the door on the slide rail, it is best for two people to cooperate, and one person will lift the door, and it will not be affected by the effect of the pulley.

In addition, a person should prepare a screwdriver and flick the top pulley of the lifting door leaf outwards to break away from the door frame. 2. Wait until it is detached, and then put down the door leaf, without the door of the pulley device, it will be easier to disassemble. All we need to do is lift the door and drag the lower half outwards to be able to disassemble it.

3. If you want to install it later, it is also relatively simple, because it is the opposite of the steps of disassembly. Dial the pulley back into the iron groove, two people cooperate, one person clicks into the pulley device, and the other person pushes it up, and it can be installed back.

How to replace the sliding door pulley when it is broken is as follows:

If the pulley device is damaged and can only be replaced with a new one, we can use a screwdriver to remove the pulley, generally it will be fixed with screws, so you only need to disassemble the screws to be able to remove the whole pulley. Then check the cause of the damage, if it is just rust, you can apply some lubricating oil, and then install it to see if it can be used flexibly.

If it doesn't work, the whole thing is damaged, and you need to replace it with a new one.

The sliding door pulley is broken and repaired:1. Disassemble the sliding door.

When there is a problem with the pulley and needs to be repaired, the first step is to remove the sliding door, lift one side of the sliding door vertically with one hand, and then slowly lift it out of the track and put it down. Then remove the other door in the same way, and this process needs to be done according to the capacity.

2. Remove the faulty pulley.

Put the sliding door flat on the ground, observe the problem of the wheel, the door frame will generally have a wool strip, remove the screw hole below, unscrew the fixed screw to pull the pulley out, and use the same way to remove the upper and lower wheels.

3. Install a new pulley.

Remove and replace the wheel, you need to replace the new pulley, stand up the sliding door part, push the upper pulley into the screw cap, in order to keep the distance between the pulleys, you can insert cardboard between the planes, and then remove them after installation, and other pulleys are also installed in the same way. Set up the upper pulley of the sliding door, insert a wrench into the round hole of the pulley that has been removed, and screw in the new screws.

Here's how:

1. First, install the upper track; It is necessary to place the track in the middle of the door sleeve, so carefully measure the dimensions of the 2 sides first.

2. After careful positioning and measurement, reassemble the five plates of the drawer, tighten the screws, and there are card slots on the drawer panel. After processing, place the drawer on the installed drawer, so that you can use an electric drill to adjust the position of the nail hole to match, and be careful not to shift when drilling.

3. After drilling holes on both sides, fix them with self-tapping screws, then drill holes in the middle, and then install screws with screwdrivers.

4. Then install the lower track installation, and wipe the bottom of the wardrobe first.

5. Position positioning of the lower rail, put the sliding door in the upper and lower tracks first, adjust the position, so that the sliding door can achieve the best sliding effect, and then follow the installation method of the upper rail, drill and then fix. Then fix the position of the lower rail, and clean the inner layer of the track with a brush.

6. Sliding door installation. First of all, lift the door gently to let the upper pulley of the door enter the upper track, and then lift the sliding door with one hand, and pull the sliding wheel with the other hand, so that the lower wheel can smoothly enter the lower track, and it is best to complete it with two people.

1. First of all, remove the sliding door and put it aside;

2. After removing it, we can see that there is a wool strip stuck to the door frame at the bottom of the sliding door;

3. Tear the strip on the door frame a little to reveal a hole;

5. It can be seen in the figure that the screws have rusted;

6. Immediately afterwards, press the pulley of the sliding door with the left hand, match the screw hole with the screw, and insert the screw hole into the screw hole with the right hand;

7. At this time, the pulley is replaced.

How to replace the sliding door pulley is broken, simple and easy to learn.

How to repair and replace the rusty pulley of the sliding door at home? In fact, the process is very simple, just look at it.

If you have tools, it is more convenient, if you don't have tools, you can only use your hands, first push the wheel in the direction of the mullion, and then use the other hand to stick into the mullion from the big mouth of the mullion and start to loosen the screw, which is basically the same when loading.