How to turn on hot water in a water heater steps, how to turn on a water heater

1: First open the main valve for water inlet, and then open the valve for water inlet to the water heater as shown in the figure; (Here from the beginning of the trip back into the house) 2: Move the hot and cold water control valve to the hot water side, and turn the water into the empty bucket prepared in advance (there is no bucket, you can put the water in the basin, this step just don't want to waste water), at this time, the metropolis.

As the water flows out, there is a gas outlet, the purpose of this step is to release the gas in the circulating pipeline of the water heater, when the water flow is uniform, there is no longer a gas jet out3: plug in the power plug; Press the junction box.

The power switch on the water heater is powered and heated, and the junction box cover is put down (indicated by the arrow in the figure) 4: At this point, the water heater has been successfully and correctly turned on, and the water has begun to heat up.

1. Plug in the power supply and press the switch button of the electric water heater. 2. Choose the right temperature for heating, or you can make an appointment for heating according to your needs. When the temperature of the water heater is heated to the specified temperature, it will be kept warm.

3. Master the water temperature according to the display screen and reach the bath temperature.

Knowledge Expansion] Precautions for the use of gas water heaters:

1. When using the gas water heater, you must strictly follow the instructions of the gas water heater for correct operation, check whether the water heater burns normally during use, and use the water heater first after turning on the power and then discharge the gas.

2. When using a gas water heater, be sure to open the doors, windows or exhaust fans, because a certain amount of air is required to burn the gas water heater. If adequate air is not guaranteed, there is a risk of hypoxia or carbon monoxide poisoning. Therefore, it is best not to use a gas water heater for a long time, because if there are many people bathing, there must be a certain amount of space.

3. Regularly check the nozzle, ignition needle and induction needle of the gas water heater. Due to the long use time of gas heaters, nozzles, ignition needles and induction needles are prone to carbon accumulation, which will affect the gentle ignition. Therefore, the nozzle and sensor needle should be checked and cleaned in time during use.

4. The wearing parts in the control system must be replaced regularly. If a malfunction or slowdown in response time is found in the control system, the control system is regularly inspected and repaired in a timely manner.

1: First open the main valve for water inlet, and then open the valve for water inlet to the water heater as shown in the figure; (Here from the beginning of the house from the outing) 2: move the hot and cold water control valve to the hot water side, open the water to the empty bucket prepared in advance (no bucket, put the water in the basin, this step just don't want to waste water), at this time most of the gas will be sprayed out with the water flowing out, the purpose of this step is to release the gas in the water heater circulation pipeline, when the water flow is uniform, there is no longer gas spray out 3:

Plug it in; Press the power switch on the junction box to supply power and heat the water heater, and put down the junction box cover (indicated by the arrow in the figure) 4: At this point, the water heater has been successfully and correctly turned on, and the water heating work has begun.

1. First open the main valve for water inlet, and then open the valve for water inlet of the water heater.

2. Adjust the hot and cold water control valve to the hot water side, and open the water into the pre-prepared container, this is because the water outlet will be sprayed out with the water flowing out, and the purpose of releasing the water is to release the gas in the circulating pipeline of the water heater, when the water flow is uniform, there is no longer gas spraying.

3. After plugging in the power plug, press the junction box.

The power switch on the water heater is heated by power, and the junction box cover is put down, so far, the water heater has been successfully and correctly turned on, and the water has begun to heat up.

A water heater is an electrical appliance where water and electricity work together, so when operating, you must master the correct steps and operate it afterwards to prevent potential safety hazards.

If you find that the water heater is not working and does not produce hot water, it may be due to the following reasons:

1. The boiling water valve of the water heater is not opened, resulting in the water heater not producing hot water, just turn on the switch.

2. If there is a problem with the water inlet of the water heater, there is no water to heat the water heater, so that there is no hot water flowing out, you can ask a professional to repair it.

3. The mixing valve of the water heater is faulty, resulting in the water heater can only send out cold water, and it needs to be repaired by professionals.

<>2: Move the hot and cold water control valve to the hot water side, open the water to the empty bucket prepared in advance (there is no bucket, put the water in the basin, this step just don't want to waste water), at this time, most of the gas will be sprayed out with the water flowing out, the purpose of this step is to release the gas in the circulating pipeline of the water heater, when the water flow is uniform, there is no longer gas spray.

3: Plug in the power plug; Press the power switch on the junction box to heat the water heater and lower the junction box cover (indicated by the arrow in the picture).

4: At this point, the water heater has been successfully turned on correctly and the water heating has started.

Detailed steps for using water heaters:

1. When using the electric water heater, turn on the power supply, the indicator light is on, indicating that the electric heating is on, when the water temperature reaches the set value, the indicator light is off, indicating that the power is cut off. In this way, the indicator light turns on and off, indicating that it is automatically holding warm.

2. The electric water heater (storage type) should be filled with water first, and then heated by electricity, and can be used after preheating. If the water pressure drops or the water stops suddenly, it is best to turn off the power.

3. Electric water heaters are equipped with faucets and are installed with reflux, which is usually used"Blue"I show cold water and use it"Red"Indicates hot water. When using, unscrew it"Red"If the water temperature is too high, it can be turned on at the same time"Blue"faucet, and adjust the amount of water output, you can get hot water at the right temperature.

4. On the temperature conditioner of the electric water heater, there is a water temperature mark scale, such as use"i"、"Or mark the position of the low, medium and high water temperature in English, Arabic numerals, and aim the temperature adjustment knob at a certain mark, and the water temperature of the water heater will adhere to the temperature set in the gear indication. When using it, let the water spill out to test the actual water temperature, and then shower to avoid the water temperature being too high.

5. When loading the water, the water outlet must be turned open, and the air in the inner tank can be checked whether the water is full after the air in the inner tank is completely discharged.

6. The power supply must be cut off before elimination.

7. When used as a blockade device, the water inlet valve must be open during heating.

8. When the valve is just opened, do not put the direction of the water outlet towards the human body.

How to open the water heater:

Plug in the power supply, press the switch button, and choose the appropriate temperature to heat, or you can schedule heating as needed. When the temperature is heated to a specified temperature, it will be in a state of insulation. Press the display screen to control the water temperature and meet the bath temperature.

When the water is heated, first adjust the valve to the ** position. When the water temperature is stable, it can be used to adjust the water temperature to the left or right depending on the temperature of the room temperature. After using it, turn off the switch in the electric water heater and unplug it after your hands are dry.

Attention should be paid to the use of water heaters:

1. The safety performance of the water heater is relatively good, and there is no quality problem itself, but it is necessary to pay attention to the correct daily use method and try not to cause damage to the water heater, so as not to bring unnecessary trouble.

2. For the use of water heaters, it is best to choose the cooperation of large brand manufacturers, so as to ensure the normal use in the later stage. And even if there is a problem, it can be solved better. Furthermore, the purchased water heater needs to pass the 3C cognitive standard.

First of all, the connecting pipe or gas tank valve is opened, the water heater battery is installed, and when hot water is needed, the faucet or mixing valve can be opened directly to automatically ignite and burn.

1. Plug in the power supply and press the electric water heater.

switch button and set the water temperature at the same time. In general, it is set at 45 degrees Celsius, but in winter, the temperature can be adjusted a little higher.

2. After the water boils, first adjust the valve to the middle position, put the water, and try that the water temperature is not cool before starting to use.

3. After the water temperature is constant, it can be used, because the electric water heater is surrounded by water, which is easy to be electrocuted, so try not to touch other places with your hands or other parts during use, especially around the power supply.

4. When using the electric water heater, when the water valve is opened and there is no water, the power supply should be disconnected immediately to prevent the electric water heater from being damaged due to failure when working without flowing water.

5. If the water pressure or voltage is too low, the use should be suspended.

6. After use, turn off the switch on the electric water heater, wait for your hands to dry, and then unplug the power.