What are the installation methods of automobile windshield glass?

1. Preparation before installation.

Protective pads are laid to protect vulnerable areas.

Protect the seat. Before activating the primer bonding, use protective tape to bond the adjacent parts of the frame in the area.

2. Remove the decorative strips, wipers, and rearview mirrors in the car.

Accurately verify the trim strips and accessories of the vehicle to be loaded.

Confirm that all necessary parts and accessories are in good condition.

Remove the trim and attachments and place them in a safe area.

If the original trim is damaged, replace it with a new one.

3. Removal of the windshield.

Wear personal protective equipment.

Use a special glass removal tool to remove broken glass.

Vacuum or brush to clean glass shards and other residual impurities.

Fourth, the treatment of the car frame.

Use a special cleaner to clean the bonded area.

Trim the strip to minimize the damage to the strip itself, and control the thickness of the remaining strip to wipe the adhesive area with a rag dipped in cleaning activator, and wait for 10 minutes to dry.

Fifth, the new windshield positioning.

Pre-positioned windshield.

In order to ensure the fast and accurate installation of the windshield after sizing, pre-positioning and marking are made before sizing.

6. Pre-installation treatment of windshield.

Wash the entire windshield.

Use a professional cleaner to treat unconventional contamination of the bonding area and ensure that there is no air or water leakage.

Apply an activator to the bonded area and activate the original black primer to make the glass bond stronger.

7. Windshield installation.

According to the actual situation, it is determined that the glue will be applied to the glass or car frame.

Accurately position the mounting glass and attach adhesive tape to ensure that the windshield is in the exact position.

Reinstall the trim strips and interior trim parts that were previously removed and restore them to their pre-installation condition.

8. Post-installation inspection.

Check whether the disassembled parts are normal.

Check that the wipers and nozzles are working properly.

Check that the relevant electronic devices are working properly.

Inspect glass tightness.

Inspect and clean the work area and sweep the truck of any remaining debris.

One is to put on the glue, stained, set the position with tape, two days after the glue is dry, there is no problem, the other is that the glass is fixed with adhesive strips, after the rubber strips are installed, then plug a string, put the glass on the frame, pull the rope out, the adhesive strip is buckled on the frame, and the glass is fixed.

The specific operation steps of the correct installation method of automotive glass are as follows:

1. Open the decorative strip of the car door.

2. Unscrew the fixing screws of the door trim panel inside the car trim strip.

3. Unscrew the fixing screws at the bottom of the door trim panel.

4. Pull outward and remove the interior panel of the door.

5. Slowly put the door glass from the glass groove into the inside of the door.

6. Insert the door glass fixing buckle and install it in place.

7. Install the door trim panel back in reverse order to complete the installation of the glass.

The specific operation steps of the correct installation method of automotive glass are as follows:

1. Open the decorative strip of the car door.

2. Unscrew the fixing screws of the door trim panel inside the car trim strip.

3. Unscrew the fixing screws at the bottom of the door trim panel.

4. Pull outward and remove the interior panel of the door.

5. Slowly put the door glass from the glass groove into the inside of the door.

6. Insert the door glass fixing buckle and install it in place.

7. Install the door trim panel back in reverse order to complete the installation of the glass.

Preheating – Thoroughly cleaning new glass – Priming applied, drying – Removing window trim – Cutting the original car.

Glass glue, remove the old glass - Trim the residual glue - If the frame is exposed metal or paint, apply a primer - Cut the nozzle as high as needed - Apply glue in a triangular section - Install the glass in the correct position before the glass glue surface dries - Install the window trim - Wait for the corresponding time according to different rubber types - Drive normally.

1. Measure the size. Before installing glass windows, people should measure the size of the balcony cover, as well as whether the window frame and glass processed by size outside the construction site meet the size of the sealed balcony.

2. Fixing the bracket. If people use fixing the windows with fixing pieces, then people should clean the base layer of the balcony openings before installation, and punch holes at the fixing points, and preset expansion bolts or plastic expansion pins to better fix the glass windows. When installing glass windows, people place the windows in a designated position and fix them with screws and plastic expansion pins.

If people use expansion bolts to fasten glass windows, then it is better to use 10 cm long bolts that are 10 cm long. If the hole is missed, people can smooth it by plastering cement, etc., but the bolts need to be 12 centimeters long so that the window frame can be more stable and bent.

3. Check whether it is on it. When the window frame is connected to the window opening, check whether the two are aligned, if not, the glass window will become more and more crooked in the later stage. If it is a regular rectangular window, people can directly measure the diagonal of the window (lower left and upper right, upper left and lower right), and the two lines are the same length.

If it is a rounded window, when measuring with a level, the bubble on the ruler in the middle indicates that the window is positive. If it is a sloping window, you need to use a hammer to measure whether the window is aligned.

4. Beat the styrofoam. After the window frame is adjusted, the styrofoam is added to fill the gap between the window frame and the wall. Once the styrofoam has fully cured (usually 2-3 hours, longer in winter), the excess styrofoam is cut off with a knife.

5. Install window sashes and other accessories. After people have fixed the window frames, the next step is to install the sashes and other accessories. Glass is fragile and must be installed with care.

6. Hit the sealant. After the glass window is installed, the sealant is evenly applied around the perimeter of the window frame to prevent rainwater from seeping into the room through the installation gaps in the window and wall.

Summary. Hello, there are two ways to install the windshield glass in the sealing strip type and the adhesive type.

Hello, there are two ways to install the windshield glass in the sealing strip type and the adhesive type.

Windshields are generally laminated glass. Laminated glass refers to a transparent adhesive plastic film pasted between two or three layers of glass, which combines the strength and toughness of the plastic with the hardness of the glass, so as to increase the shock resistance of the glass. Tempered glass refers to ordinary glass that has been quenched and formed into a certain internal stress in its internal structure, so that the strength of the glass is strengthened.

When shattered by impact, the glass will crack into small pieces with blunt edges, which is not easy to cause injury to passengers. Area tempered glass is a new type of tempered glass, which has been specially treated to keep the cracks of the glass in a certain degree of clarity when it is cracked by impact, so as to ensure that the driver's field of vision is not affected. At present, the front windshield of automobiles is mainly laminated tempered glass and laminated tempered glass, which can withstand strong impact force.

After replacing the front cleaner and windshield, you should pay attention to:1When replacing the front windshield, make sure that the glass cannot be repaired before replacement.

If you can repair it, try to use the repair method, because it takes a while to replace the front windshield, except for a certain cost. 2.Attention is required after replacement.

Don't worry about the film. It should last at least 7 days. 3.

After replacing the front windshield, don't rush to run at high speeds. Don't drive at a high speed and keep it within 80 kilometers per hour. 4. Also pay attention to the road section, avoid too bumpy, reduce sudden braking or acceleration, and avoid the displacement of the front windshield.

5.After replacing the front windshield, you can't rush to wash the car. Before washing your car, remove the tape that holds the windshield in place.

6.Do not open the windows too early to avoid the front windshield being displaced due to the ride. 7.

Do not insert cards such as parking permits into the gap between the front windshield and the center console.

What are the installation methods of wind and window glass? What are the requirements for installation?

Hello, glad to answer for you. <>

There are two ways to install the wind and window glass: the outer installation method: the workers stand on the outer hanging basket for installation.

The glass is fixed with a sealing strip on the inside, then from the outside, and a sealant is injected into the cavity to fill the gap. Inner installation method: The staff stands on the ground in the room for installation.

Now fix the sealing strip in the groove on the outside of the window car to fix the position of the glass, and then fix it from the inside, and inject sealant into the cavity of the notch to fill and fix. This method is the opposite of the outward mounting method. If glass windows are installed on higher floors, you must pay attention to safety, and you can use ropes to tie the waist or hands and feet of the staff, so that even if there is danger, you can rescue in time.

It is necessary to inspect the glass tightness and inspect and clean the work area, sweeping the remaining debris inside the vehicle

Installation method of glass door:

1. Pay-off positioning: a glass door that combines fixed glass and active glass door.

2. Install the limit groove at the top of the door frame: determine the center line and the edge line of the two metal decoration plates, and carry out the device of limiting groove on the top of the door frame according to the edge line of the hail orange accompanying the decoration board.

3. Device wooden bottom support: nail the square wood to the embedded wooden brick and fix it on the ground.

4. Install the vertical door frame: determine the center line nail the door frame square wood, and then determine the shape and orientation of the door frame column.

5. Install the glass: Tighten the thick glass, lift the thick glass plate, and move it to the exact position to be installed.

6. Seal with glass glue: inject glass glue into the two sides of the top limit groove and the bottom bracket notch, the joint between the thick glass and the door frame column, etc.

7. Docking between glasses: When the glass door is fixed due to the large scale and the glass needs to be spliced, the edge of the glass plate should be chamfered.

8. Dynamic fiber glass door leaf device: the positioning pin of the ground spring and the top surface of the door frame should be positioned to complete the device, and the two must be coaxial, and the device should be checked with a hanging line to ensure that the center line of the ground spring shaft and the positioning pin is in the same straight line.

9. Device upper and lower door clamps of glass door leaves: The upper and lower metal door clamps are installed at the upper and lower ends of the glass door leaf to measure the height of the door leaf.

Near Taitung 6th Road and Taitung 8th Road. There are two glass shops that do it very big. Just ask around the neighborhood.

Answer: Whether it is plastic steel doors and windows or aluminum alloy doors and windows, glass must be installed. In the process of door and window production, the installation of glass is a relatively simple link. However, if the glass has been installed and is accidentally damaged later, or the glass variety is replaced, it is relatively troublesome.

To replace the installation glass, first of all, you need to remove the glass strip, the glass strip is a special material for fixing the door and window glass, and when dismantling, you need to insert it from the flat mouth of the door and window profile with a flat screwdriver, and then pry the glass strip up, so that the strip appears larger, and you need to move along the seam, remove the glass strip, and then remove the old glass, replace it with a new glass, put the strip into the notch of the strip in the two glasses, and hammer it with a wooden hammer.