Who would do a better float? 20

1.The main thing should be to choose a beverage straw with appropriate length, thickness of 15 20 cm, diameter of about 2 3 mm, bright and white tube body, and no damage.

2.Choose a small piece of automotive inner tube film with good elasticity, and those who are aging and have no elasticity cannot use it.

3.A section of the valve core hose for a bicycle.

How to make parts.

1.When making, bake one end of the beverage straw over low heat, quickly use the thumb and index finger to clip a small piece of cloth on the baking place, and gently pinch it to make the hose hole glued and sealed. According to this method, seal the other end of the straw, and then use a No. 1 small pen or small cotton swab to dip the red paint on the tail of the drift and paint a red cap.

Then paint a few small red grid circles at an appropriate distance below the red cover. (You can refer to the vertical drift grid for sale). In this way, the drifting process has been completed, and after drying, this small vertical drift can be used for assembly and fishing.

2.Use scissors to cut two small plastic particles about the size of mung beans about centimeters long on the edge of the film with scissors to replace space beans.

3.At one end of the valve core hose, cut off two valve core rubber rings about a centimeter long to replace the drift seat.

Installation method: When assembling, thread the bus bar with a fine flower needle at one end of the busbar, and pass the needle from the long end of the first rubber grain through the other end of the long (so that the retention on the rubber particle ** is better). Thread the two valve core loops from the needle onto the busbar.

Then follow the above method to thread the second rubber pellet on the bus bar (the two valve cores are between the two rubber particles). After removing the pin, tie the hook and sinker to one end of this busbar (the size of the hook is determined according to the needs and habits of the angler). Finally, one end of the drifting head is inserted into the two valve core rings, and the upper rubber ring is placed directly above the drifting head at 1 3 places.

Place another rubber ring below on the drift head and fasten it to the fishing line. In this way, the rig assembly is complete. After adjusting the water level and drift distance when fishing, the rubber particles are moved on the upper and lower bus wires of the two circles of the valve core of the adjusted drift position, and the drift position is firm and reliable, and the drift will never slide.

Advantages of the use of bleaching.

1.The materials are easy to find and easy to make.

2.It has the advantages of small weight, light weight, large buoyancy, uniform length and slenderness, and good wind and wave resistance. Coupled with this sensitive drift body and eye-catching red and white grid, the fish bite response is obvious, and elderly anglers with poor eyesight can also accurately observe the drift and lift the rod in time.

3.Durable, not easy to break, after a comparative test fishing, its service life is more than twice that of the city's most ordinary vertical drift, which is economical, money-saving, trouble-saving and time-saving, and is also suitable for use in any fishing tackle fishing rig.

What kind of drift you use depends on where you are fishing. If you are still using hard plastic in the inner lake. If it is a marine fish, it must be made of soft plastic.

Commonly used freshwater fishing buoys should be divided into four categories: long soft tail, long hard tail; Short soft tail, short hard tail. They have different divisions of labor:

The long body mark has good stability and is suitable for bottom fishing; The long soft tail is suitable for fishing slippery fish, and the long hard tail is suitable for fast fishing. The short body mark has good sensitivity and is suitable for fishing; The short body and soft tail are suitable for fishing the very weak fish, and the short body and hard tail are suitable for fishing floating and fast fish. The expansion degree of peacock feathers after temperature difference is greater than that of balsa wood, and balsa buoys should be preferred.

There is also the "Dharma" mark made in Taiwan, if you buy **, the quality is also very good, and the market price is about 60 yuan.

1.Fishing float Fishing float usually has to use a large float of 6-7. The float of the white carp of No. 3-4 is small due to the small buoyancy, so it is difficult to control the large bait and the small bait.

2.Fishing bottom: Usually 4-5 is sufficient.

3.The choice of large drift and small drift mainly depends on the target fish and the depth of the water. For example, the white carp, because of its requirements are particularly sensitive, and the bait and hook are very small, you can use "small fish" No. 3-4, but it seems to be too "sissy" to fish tilapia, and if I want to say it, there is a feeling of "little white face".

Because tilapia baits and hooks are usually much larger. In addition, the depth of the water is also an important factor. I usually use meters as a standard.

meters below the meter, usually with trumpet drift as the most; meters above, especially sometimes at depths of 3 meters, large drifting is the only option. Because this can not only alleviate the trouble of being snatched away by small fish when fishing deep, but also help to shorten the sinking time. However, special attention should still be paid to sensitivity issues when drifting with large ones.

It can be large or small, and it should be small.

4.Peacock feather balsa wood is better than the former if you consider it only in terms of durability. However, it should be noted that there are two kinds of drifting feet of Basha wood drift, one is a fine carbon rod, and the other is a conjoined wooden foot, the latter is easy to break when inserting.

In terms of sensitivity, the former may be better than the latter.

5.Hollow solid tail There are two main differences between the two: buoyancy and the ease of apparent drift.

The buoyancy of the hollow tail is greater than that of the solid tail, so its sensitivity is theoretically less than that of the latter. But how it actually is depends on your feelings and preferences, because theory may not necessarily be practical, and the impact on the outcome is different. If it's not a professional game, there may not be a noticeable difference.

Because the density of fish in recreational fishing is usually limited, it is difficult to compare the speed (number of tails). It is worth mentioning that the solid drift tail is very thin, and it certainly does not look as easy as the hollow drift. This should not be ignored for anglers who often use a rice rod, or who target fish other than white carp, or who have a windy and cloudy day.

The bottom of the fishing can be selected with "Dharma" soft tail or "crown" soft tail, if the fish eat very lightly, or the fish is more slippery, you can choose to use the "Dharma", "Crown" long body small hard tail drift. Fishing floats can be short-bodied, hard-tailed floats of "Dharma", "Crown" or "Dancing Queen".

Different fishing grounds should choose different floats.

Generally speaking, when the water is shallow, the bottom is flat, the fish is small, the fish is cunning, and the bite is light, you can use a trumpet, a thin tail, and a more sensitive float; The water is muddy, the flow is large, the bite is heavy, the small trash fish is few, the raw mouth fish, and the water surface is large, and the float with greater buoyancy can be selected.

The fish mouth is small and the drift is small; The fish mouth is easy to use and floats; Deep water fish use big drift; In early spring and winter, fishing with small drift, fishing in normal seasons, fast use big drift on fish, even if the water is shallow, use big drift. The fish is slow, even if the water is deep, the fish should also use small drifting. The fish is cunning and drifts with a hollow soft tail; Raw mouth fish are floated with a hard tail solid body.

The mouth is large, and the fish is quickly adjusted to a higher mesh, 6 meshes or even a dozen meshes. The mouth of the small fish is small and lowered, and the 3, 4, and 5 meshes can be adjusted. If the fish mouth is good, you can adjust the eye to fish low; (e.g. Tune 5 Fishing 3).

If there are trash fish, or the fish is slippery, you can lower the mesh and fish the high mesh (for example: leveling the water to fish 3 mesh; Tune 3 mesh fishing 4 mesh).

It's a lot. The buoys selected for different water conditions, fish conditions and other factors are different.

Get a buoy, from the bottom to the point, it is composed of the foot, the body and the marking part, the body is called the main buoyancy body, the indicator is called the secondary buoyancy body, the thickness, length and shape of the body determine the performance of the buoy. Generally speaking: the standard body is short, the center of gravity is downward, such a buoy enters the water and turns over quickly, which can better capture the fish signal of the upper fish; On the contrary, the body of the buoy is long, spindle-shaped, the center of gravity of this buoy is upward, and the actions after entering the water are:

Turning over, standing (relatively slowly), then sinking, pausing, and finally stopping at the fishing target (the point where the horizontal plane intersects with the indicator is called the fishing mesh), which is more suitable for fishing for demersal fish.

No matter which label you choose, it is very necessary to first check that the stick is straight from head to toe; Then look at whether the paint surface of the label body and its joint parts is smooth; Finally, I asked about the material of Xiaocun, and the material of Peacock Feather is better, and the label of this material is suitable for almost all non-competitive anglers.

Don't worry about it, the quality of the king's eye is good** and suitable.

In terms of stability, the float of Barr fir is better, and in terms of sensitivity, the float of reed is better.

Balshan is said to be the lightest wood in the world, with its soft, buoyant and light and porous texture. Its features are as follows:

1. The plasticity of balr fir wood is very good, and it can be made into a variety of forms of floating. 2. Barr fir is less affected by weather and temperature and other factors, and it is not easy to draft, and it is rare to run the target. Moreover, its density is evenly distributed, and the center of gravity is stable after being made to float, so its stability is very good.

3. The sensitivity of the balr fir float is worse than that of peacock feathers and reed floats, but it is enough to deal with general fish conditions. Moreover, poor sensitivity is not necessarily a disadvantage, in some fish conditions, such floats can filter out some false signals. 4. Wood is relatively easy to obtain, and it is not difficult to make bleaching, so it is relatively cheap.

5. The float of Balshan wood is relatively brittle, and it is easy to break if the throwing rod hits a hard object.

Peacock feathers are mostly made from the tail feathers of male blue peacocks, with thick hair stems and large buoyancy. Its features are as follows:

1. The plasticity and elasticity of peacock feathers are very good, and they can even bend the body into a circle, which is very durable and not easy to damage. 2. The float made of peacock feathers is not easy to draft, and is less affected by factors such as weather and temperature, and has a very strong stability. 3. The sensitivity of the peacock feather float is between the balr fir and the reed float, and the response to some small signals is clear and accurate, which is suitable for fishing slippery fish.

4. The cost of peacock feather float is high, and the difficulty of production is relatively large, so it is high.

The reed float is generally made of dry reeds, rather than the hollow water reeds in the Baiyangdian area. Dry reeds are dense, strong and impact-resistant, and are good materials for processing high-grade floating. Its features are as follows:

1. In the same volume of floating, the sensitivity of reed float is the highest. 2. If the reed float coating is not handled well, it is easy to crack and the draft is messy, resulting in poor float stability. 3. The float made of reeds is prone to uneven density distribution, so that its center of gravity will be offset, which will also affect its stability.

4. The plasticity of reeds is not good, and the processing technology is relatively complex, and the rejection rate is very high, so the general high-quality reeds will be very expensive.

Most of the nano floats are conceptual products, and their material is actually a polymer plastic foaming material. The characteristics of this floating material are different depending on the ratio at the time of production. Its features are as follows:

1. The plasticity of nano float is very good, and it can be made into any form, and it is not easy to be damaged and durable. 2. Nano float has no draft, basically not affected by weather temperature and other factors, and the stability coefficient is very high. 3. The production is relatively simple, and the cost is low, so it is cheaper.

4. The material of nano float is an uncertain factor, if the material is not ideal, the sensitivity may be very poor; Of course, if the material is ideal, it will be a perfect float.

When fishing, how to choose the size of the float?

Fishing is a technical job, in fact, it is also a "luck job", but choosing a good float and a suitable float to fish is a purely technical job. This is a bit cruel for many novice anglers, because there are so many types of floats. In fact, it is not difficult to choose a good float, let's talk about it in this issue of "Fishing Class".

1. First of all, the selection of floating materials and cutting lengths.

2. Round with a glass tube and then cut according to the drift shape.

3. After cutting the reed floating drifting material, the water chestnut is polished to make it smooth and ensure that the density of the knife edge is good after bonding. Here's a comparison between sanded and unpolished.

4. After finishing, it should be shaped to ensure that the specifications of each reed float are as the same as possible.

5. Glue underneath, and insert the drifting tail and drifting foot at the same time. After the bonding is completed, it is necessary to carry out repeated straightening, and the first step is very important.

6. Remove the stitches on the 3rd day after bonding.

7. After dismantling the thread, scrape off the residual glue.

8. After scraping, use a grinder for grinding.

9. After grinding, gold threads should be wrapped at both ends.

10. Cover with makeup after wrapping the thread, and hit the black bottom once.

11. Then sprinkle laser gold powder.

12. Then draw a small gold circle and a small red circle, and the makeup is completed.

13. Then use a pad printing machine to print your own trademark.

14. The back is the topcoat 2-3 times, and the number of meshes is completed.

Regardless of the type of float chosen, the tail should be bright in color for easy observation when fishing. When selecting the drift, it is better not to be skewed, no cracks and no air leakage.

Float selection. The choice of float should be based on the difference in the fishing method used, the depth of the water at the fishing point, whether there are waves on the water surface and other factors.

When floating fishing, the gravity formed by the total weight of the plumb sinker and hook bait in the water body is less than the buoyancy of the float, and the ball float or float is generally selected.

The body is stubby and short, and the vertical drift is short. Some anglers temporarily switch to float fishing in the fishing grounds, and wearing a piece of styrofoam on the pole float can also solve the problem.

In bottom fishing, the sum gravity of the plumb sinker and hook bait used for float fishing in the water column is equal to the buoyancy of the float. If fishing in deep waters, you should choose a float with a larger buoyancy and a larger plumb sinker to achieve the purpose of making the hook bait fall to the bottom quickly after entering the water, so as to prevent the middle and upper small fish from grabbing the hook bait. If the wind is strong when fishing, you can choose a wind drift or horizontal float with a slender tip and an empty ball at the bottom of the drift body.

Regardless of the type of float chosen, the tail should be bright in color for easy observation when fishing. When selecting the drift, it is better not to be skewed, no cracks and no air leakage.

In order to adapt to the changes in the conditions and environment of the fishing site, anglers should bring several floats before each fishing trip, so that they can be replaced when the fishing method is temporarily adjusted.