Blue Sand Restore Card Network Clone 10

Just take the reduction card down and you're good to go.

What restore card are you using? Do you support network copying?

Open one of the machines to modify all the parameters, as a template, use Founder's own network deployment tool to transfer the task, wait for login, and then manually start all the machines, among them, press F2 to find the template machine when booting, wait for all to log in, click to complete the login, and then network cloning, the speed is about 700m min, CMOS cloning and driver are useless, don't care, end OK

If you use a USB flash drive as a cloning tool, you don't need to clone the driver facility, because you are a local area network, so the IP should be dotted allocation.

Open the Founder protection card,The premise is that the line is installed,Open it and then enter the management page,Because I haven't done it for a long time,So I don't know where it is,It seems that there is a waiting login bar,If it's a one-to-one cloning then you plug in the network cable,Click to wait for login,After showing the plugged in computer - complete the login - network cloning,If it's one to many,Click to wait for login,Other computers will be displayed (provided that the line is connected),If it's all displayed, click to complete the login, and then click on the network cloning, if there are a lot of computers, the cloning will be very slow, and the simultaneous interpretation will be faster.

Open the Founder software protection card and network deployment, and there is network clone in this interface.

What do you mean by network cloning?

I've only done it on a LAN where I can copy all the data from one computer to another computer (including the system) with a single cable, so that both computers are exactly the same.

If you are unable to log in to the "Driver" mode during "Network Clone", you can press F2 at startup to log in to "Network Deployment" using ROM mode. "Restart" those computers remotely in "Network Deployment"; Then "wait for login", you can make the corresponding computer use "driver" mode to log in, and you can "network clone".

Non-driver format (ROM format, or Windows format), the machine in the computer room has this problem at the time.

I don't know the reason, you can try it this way and see if it solves the problem. That's how mine was made. ）

1."Driver parameter update", it will prompt to restart, "Yes";

2.When connecting to the sender, "Complete Login". Select Network Clone.

The problem I encountered was,After this "network cloning",I can't get into the system when I boot up.,There's a line of green font on the screen.,I forgot what it is.,It's annoying.,Later, I connected the sender again.,And then "drive parameter update" to it.,That's it.。 ）

If the root progress is the same, why don't you try "progress sync" to see if it works?

Good luck...

What do you mean by software? Founder protection card or Founder emergency center or Founder with the operating system or or network clone of Founder protection card??

Install the Founder Protection Card according to the instructions, as long as one point is to choose your own hard disk interface.

Network cloning of the protection card, for example: computer A has a system, boot into the protection card of computer A as the sender, and then turn on computer B will directly enter the network copy, click the send of computer A.

The emergency center is guided by the boot of the driver disc after the system installation is completed, and then the installation is OK.

How to turn off the built-in network cloning wild high mega function of computer song rental?

Can you be specific?

However, I think this kind of feature will start a corresponding service at the first glance.

Just turn off the service.

There are many reasons for this problem, the first consideration is whether the network cable is connected, it is best to change the network cable and try again, if there is no problem with the network cable, the second possibility is the problem of the restoration card, this problem is very likely, the restoration card is built-in, and can only be repaired by the merchant. The third possibility is that if the sending host has already started to send data, then the new machine will keep searching for the sending host, and the sending host will not be searched at this time. This is generally the case.