How do you take out the plug in the bathroom basin?

The stopper of the bathroom basin can be taken out with a shoelace, that is, the shoelace is passed under the stopper, and the two ends can be pulled out by pulling it upward, and the specific operation steps are as follows:

1. Smooth a shoelace into the floor drain.

2. Find a thin wire.

3. Use a thin wire to pull the laces out of the other.

4. Hold the two ends of the shoelaces tightly and pull hard.

5. At this time, remove the stopper of the washbasin.

Press-down drainer (push-to-plug). In fact, the most common washbasin drainers are press type and flip type, these two types of drainers have their own advantages and disadvantages, so many people choose different focuses, both of which are now very popular.

Like my press drainer, although the appearance is good-looking, the water storage and water discharge are better than the flip drainer, but after a long time of use or if the internal parts of the drainer are loose, there will often be no response to the press, and the pool is full of water. At this time, the drain can only be disassembled, the dirt is cleaned or replaced after the parts are installed to solve, the maintenance worker said that because the disassembly and installation are more complicated, it is best to ask professionals to get it!

Relatively speaking, the biggest disadvantage of the flip-type sewer is that it cannot be completely water-leaking when storing water, but the flip-type is more flexible and convenient to use, and it is relatively simple to repair and clean, but it is still that sentence, depending on the focus of your choice to decide which one to install at home.

The maintenance worker taught a soil method, you can try soapy water first, or regularly take an old toothbrush and brush it a few times (so that the dirt accumulated around the plug can be brought out) and then press it at multiple angles to try, go into the water super fast, and you can repair it yourself after learning it, no need to hire someone. Therefore, when choosing a sink, not only should you pay attention to the overtop basin or the undercounter basin, but the quality of the drainer is also crucial!

If the stopper of the sink is rotated, it can be removed by using a lever with a stick.

Just pry it out. If you want to press the plug, you need to find the turnbuckle that holds the plug under the basin, and unscrew the turnbuckle to remove the stopper.

There are usually two types of sink plugs, one is rotary, and this plug is very easy to remove.

We only need to prepare a small stick that is strong enough, turn the plug up first, then put one end of the stick under the plug, and hammer the other side of it, so that it can be easily pried out by the lever principle.

If it is a press plug to be removed, it is more complicated, usually there is a turnbuckle under the basin of the sink that uses this plug, the function of this turnbuckle is to fix the race head, we only need to unscrew it to remove the stopper.

If you want to remove the washbasin stopper, you can try the following two methods:

1. If you want to disassemble the flip plug of the washbasin, it is very simple, you can prepare a pliers, and then clamp the flip plug of the washbasin. After that, pull it up hard, you need to pay attention to balance when you pull it, and you must not hurt yourself, and then as long as you pull it out, you can effectively loosen the flip plug;

2. But there may be times when it is stuck, there is no way to pull it out, we can observe whether there are some sundries around, such as hair or other small wooden sticks clamped, take things out, and then flip them over, add lubricant, let the lid lubricate, and then use pliers to clamp the lid and take it out.

Method 1: Remove the U-shaped pipe under the washbasin, then take a stick from below and poke it at the basin plug, poke the basin plug out, and then connect the U-shaped pipe.

Method. 2. Find the place where the gap between the pot plug is slightly larger, and then use a screwdriver.

Or a hard object with a relatively small contact surface can reach in and pry the basin plug up.

Method. 3. Melt fertilizer soap with warm water to make soapy water, then pour the soapy water on the washbasin plug, wait for a while, and then try to press the spring plug a few more times.

Tips for cleaning the sink:

1. In fact, long-term use of the sink will produce a large amount of scale, and the negative scale on the sink will make the sink dull.

2. First of all, we can use professional dish soap.

Carry out right side cleaning, pay attention to the use of a dry cloth to wipe during the cleaning process, and do not use steel wool to wipe, to avoid wiping off the glaze of the sink, so as to cause the sink's aesthetics to be insufficient.

3. You can also use soap to wrap a thin layer of rags, first of all, the rags can not wring out the water, we wash the rags wrapped in soap, so as to avoid scale in the sink.

What should I do if the plug in the bathroom basin won't open? Hello dear, hello there are two ways to try it:; First, you can use a small driver to find a position with a little gap, and the disadvantage is slowly upturned, and it can be opened slowly.

Second, there is a screwdriver and a hammer at home. With a flathead screwdriver, the bit is placed on the edge that can be rotated, and the tail of the screwdriver can be opened by hitting the tail with a hammer. Hope it helps.

The steps to cut out the sink plug are as follows:

Tools: blades, shower gel.

1. First of all, squeeze two drops of shower gel out of the sink stopper.

2. Then use your hands to evenly apply the shower gel to the entire edge of the stopper.

3. Then prepare the blades and other tools.

4. Then slowly the tool along the seam of the edge of the plug.

5. The plug is warped.

The stopper of the bathroom basin can be taken out with a shoelace, that is, the shoelace is passed under the stopper, and the two ends can be pulled out by pulling it upward, and the specific operation steps are as follows:

1. Smooth a shoelace into the floor drain.

2. Find a thin wire.

3. Use a thin wire to pull the laces out of the other.

4. Hold the two ends of the shoelaces tightly and pull hard.

5. At this time, remove the stopper of the washbasin.

<> generally there will be a special button to fix the plug below the sink, lift the button and rotate the plug a few times to take it out, if there is no buckle to fix the stopper, you can also use a tool to warp the stopper, use the lever principle to stick or wire into the plug and then warp it in the opposite direction, the plug can be cut out, and finally the pipe under the pool can be unloaded, after unloading, the plug is pushed out with a tool from below, and it can be cleaned. If the plug is flipped, you can use a screwdriver to jack the plug up and hit it with a hammer a few times to remove it.