The stove goes out as soon as you let go of the stove, how can you fix it?

We all use gas stoves when cooking, and there are a lot of minor problems when using gas stoves. After turning on the gas stove and igniting the fire, the fire will be extinguished as soon as you let go of the hand, so what should I do at this time? Let's take a lookGas stovesAs soon as you let go, turn off the fireWhat to do and what can I do to fix it?

How to use the gas stove correctly and safely in daily life? When the gas stove does not catch fire, we must first rule out whether the liquefied gas cylinder is out of gas, or whether the gas is in arrears, if it is not for this reason, we have to check the gas stove lighter, we see this white is the gas stove lighter.

There are two needles in the stove head, one is white electrode, and the other is black, which is the induction probe, and there is a slit in the fire, which is the fire channel, and the small gap in the fire can burn the induction probe, so that the fire burns normally after letting go. Adjust the damper, don't let the damper be too big, because the damper is too big, it will blow the flame. Therefore, while lighting the fire, adjust the bottom air hole.

Don't let go after lighting the flame, and then open the door of the cabinet to see that there are two damper paddles at the bottom of the gas stove, the paddle on the left is a small fire in the center of the tube, and the paddle on the right is to adjust the fire in the outer ring, and the paddles can be adjusted left and right.

<> microswitch is damaged. Inside the switch of the gas stove, due to frequent switching or use for a long time, there is wear or crack, or the switch is in poor contact, because it is a very small place inside the switch, it is a fine and professional work, it is recommended to ask professionals to repair, observe whether the small fire cover or the central fire cover can completely cover the flame on the protective needle when burning, if there is no flame to the flame-out protection needle, it will definitely be extinguished, this is you need to adjust the inner fire cover to have a fire hole against the flame-out protection needle.

The high-voltage output wire is broken down or cracked, resulting in leakage, and the fault can be eliminated by replacing the new wire; Due to too much fouling and weak discharge, the electrode needle should be cleaned frequently to keep the electrode needle clean; The gas stove pipeline is blocked, and only the gas can ignite and burn for a short time, and once the pipeline gas does not come up, the fire will be extinguished and the gas pipeline will be replaced.

In fact, this is because the switch of the gas stove is broken, and it only needs to be replaced with a new one.

It is likely that this situation is due to insufficient ventilation, and we should let it be ventilated first, and secondly, it should be ignited for a longer time.

It may be that the wires inside are loose, open and connect the wires inside, and use vinyl on the boat.

1. Check the gas source

When the gas stove does not catch fire, first check the gas source, whether the gas source has been turned on, whether the gas source is sufficient, especially the family using liquefied gas needs to pay attention to this, if the liquefied gas is gone, it is recommended that you usually develop the habit of regularly filling liquefied gas to prevent it from happening.

2. Check the battery

If you make sure that the gas stove has been ventilated, but it still can't be turned on, then you should pay attention to the spark when we light the fire, carefully observe whether the spark is weak, and pay attention to whether the ignition sound is weak and weak.

If this is the case, it means that the battery is out of power or the line is in poor contact, and this solution is also very simple, just replace the No. 1 dry battery, if there is rust in the battery case, you must remove the rust, pay attention to the position of the positive and negative electrodes when putting the battery, and place it accurately so that the whole circuit is closed.

3. Check the hygiene of the ignition needle

If the stove is not taken care of for a long time, the ignition needle will be easily stained by the oil, and the ignition needle will not be successfully ignited to prevent us from cooking and stir-frying, so we will use a dry towel to wipe the ignition needle clean, and then try to light the fire.

4. Check the position of the ignition needle

Contrary to the daily cleaning of the ignition needle, the ignition needle is cleaned too much, and it is easy to deviate the position of the ignition needle if it is too much cleaning or careless cleaning, because the gas stove has certain requirements for the distance between the ignition needle and the fire cover, and once the deviation distance is too much, the gas stove will not catch fire, usually the distance between the ignition needle and the fire cover is 4-6mm, and it should be aimed at the fire hole.

4. Check the blockage of the pipeline

If there is no problem with the above four points, then check whether there is a clogged pipe or a clogged nozzle. If you can smell the gas odor but can't ignite the fire, it means that the gas pipeline is blocked, and you need to dredge the pipeline, check the gas outlet valve, clean the small hole of the fire cover with a toothpick, and re-place it to try to start the fire.

It may be that there is a problem with the flame-out protection probe or flame-out protection switch.

Looking at the stove, there are two needles, one is a spark, and the other is this protective probe.

If the probe is wet or the lower wires are not in good contact and cannot transmit a temperature signal, the furnace "thinks" that it has accidentally stalled and cuts off the gas supply.

If you don't let go, the gas supply is mandatory, and as soon as you let go, the furnace "takes over" control, and it is treated as extinguished, and the fire is extinguished.

So start with this probe and check all the way down to the controller inside the furnace.

Generally, the probe is wet, rusty, or the bottom connection is broken.

It is also possible that the flame in the inner ring cannot burn the probe, and the probe cannot be heated, so the controller thinks that the flame is extinguished, and the gas is "cut off" when you let go. Try adjusting the damper in the inner ring to allow the flame to reach the probe sufficiently.

The general reasons are:

1.If the gas stove is equipped with flame-out protection, it may be that the flame-out protection device is damaged. Solution: Replace the flame-out protection device.

2.The damper under the gas hob is not in the right position. Solution: Adjust the damper.

3.Damage to the rotary knob or lighter. Workaround: Replace.

For more information, please call us.

The gas stove cannot be ignited normally, which is caused by the failure of the temperature sensing head of the igniter, and the valve cannot be opened, and the ignition of the same model can be used normally.

Do not let go for more than five seconds after the fire, see if the fire can burn to the temperature sensing probe, if the flame does not burn, adjust the damper (under the stove).

If you can burn the temperature sensing probe for a long time or turn off, it is recommended to find a professional repair, and it is a bit troublesome to repair it yourself. The new stove generally lets go of the fire, because it is caused by the fact that the fire is immediately released, and the stove damper is not adjusted to the middle position of the stove head, and there is no fire, and the temperature sensing probe does not receive the temperature signal.

The gas stove will be permanently aging of the high-voltage line, the most direct impact of this is that it cannot be ignited, and it is necessary to install high-voltage protection, it is recommended to ask professionals to repair, because you can't find the high-voltage line by yourself.

You see if it helps you.

It's plagiarism and doesn't get to the point.

Close the damper small, the small iron piece at the bottom, and turn it to the left, and wipe the sensor needle.

Clean and adjust the thermocouple and try again after drying.

The gas stove may be extinguished when the fire is set on fire, which may be caused by the excessive adjustment of the damper, which is easy to cause the flame to leave when the damper is adjusted too large, and there will be a situation where the fire is extinguished when the fire is released. When using an electric gas stove, the ignition will turn off if you let go too quickly after ignition. There is usually a flame detection motor on the gas stove, and if the flame does not burn to the flame protection needle when using the gas stove to ignite, it will definitely go out when you let go.

The natural gas stove is ignited by an electronic lighter, and if the hand releases the knob while ignition, the electronic lighter will stop the ignition operation. So as soon as you let go of your hand, it is impossible to light the fire.

It may be that the battery below is loose, this is the case in my house, when the hand is pressed, it will be extinguished as soon as the hand is loosened, so you need to see if the battery is intact and has not fallen off.

This may be because your natural gas is not very sufficient, and some virtual gas will be produced when you hit, and there is no way to support the formation of flames.

This may be because the bottom battery is dead, you can try to replace the battery, it may also be because of a problem with the air valve, or it may be because there is a problem with the electronic coil of the stove itself, and the latter two problems are best repaired by a professional.

Here's why:

1. It may be that the time of holding down is not enough, and now Chunyu's electronic ignition gas stove is equipped with flame-out protection equipment, which means that the ignition needs to be pressed for 5 to 10 seconds before the induction needle will work.

2. If the battery of the gas stove is dead, there will also be a situation where the engine will go out as soon as you let go. The battery of the gas stove needs to be removed and replaced with a new one.

3. Look carefully at the top of the stove to see if there is a blockage, if it is blocked, it needs to be cleaned up in time, and a thin wire can generally be used for dredging. If there is carbon accumulation on the edge of the ignition needle, you can use fine sandpaper for polishing, pay attention to the strength to avoid short circuits.

4. Check the central fire cover of the gas stove to see if it will cover the protective needle when it burns. It needs to be repaired in time so that the ignition source can cover the protective pin.

5. It is also possible that there is a problem with the solenoid valve, so it is necessary to replace a new solenoid valve.

The reason why the stove is extinguished is to ensure the safety of the use of the gas stove and avoid serious accidents such as fire and **.

The fire on the stove is extinguished, and it is mainly related to gas safety. The gas stove is burned by burning gas to heat food, and the gas itself has the nature of flammable and explosive, once leaked or used improperly, it will cause fire, ** and other serious accidents. Therefore, in order to use it safely, the inventor set up the operation of the stove to fight the fire and extinguish it.

When we use a lighter or lighter stick to light the gas stove, we need to press the ignition button for a long time to make the gas nozzle continuously emit gas in order to ignite the gas. If, after igniting the gas, the lighter or lighter stick button is released, the flame is extinguished so that no more gas is coming out of the gas injector.

In addition, the gas stove also has a safety device, once the flame is extinguished or the gas leak is detected, the safety device will automatically cut off the gas** to avoid the occurrence of fire or ** accidents.

Introduction to stoves

A stove is a type of kitchen equipment used for cooking, baking, and other heat-treated foods. Stoves typically provide heat from energy sources such as gas, electricity, or firewood and are used to heat cooking appliances such as pots, pans, baking trays, etc. There are many types and forms of stoves, including gas stoves, induction cookers, traditional stoves, ovens, etc.

Gas stoves are one of the most common types of stoves. It uses gas as a heat source, sprays it out through a nozzle, and ignites the gas. Gas stoves are economical and practical, and they heat up quickly, but you need to pay attention to safety issues.

An induction cooker is a type of stove that uses the principle of electromagnetic induction for heating, which uses electricity as a heat source to generate a magnetic field through electromagnetic induction, so that an electric current is generated inside the cooking utensils, thus generating heat. Induction cooker has high heating efficiency and easy operation, but it is necessary to pay attention to the safety of the power supply.

The above content refers to Encyclopedia - Stove.

The gas stove is extinguished as soon as it is on fire, and the treatment method is as follows:

1. Whether the operation is correct.

Gas stoves are equipped with flame-out protection devices, generally thermocouples, when the temperature does not meet the requirements of the hall key thermocouple, the thermocouple will cut off the gas**. So, in general, you need to press 5 for 10 seconds before you can let go.

2. Check whether the flame distributor of the gas stove is well placed

If the flame separator and the flame separator seat have buckles, the buckles need to be aligned, if the buckle is moved, not only will the flame go out when you let go, but also cause the flame separator to burn and deform.

3. Check the thermocouple

If the thermocouple is broken, or if the thermocouple is too far away from the flame, it may not catch fire.

4. Check whether the battery has charge

The gas stove needs to use a battery, if it can't catch fire, you can observe the spark when the gas stove is ignited, if the ignition sound is weak and the electricity frequency is low, it is likely that the battery is insufficient, and a new battery can be solved.

5. Other issues

If the above problems are ruled out, but the gas stove is still extinguished after ignition, it is likely that the connection between the flame-out protection needle and the solenoid valve is broken, or the damper regulator is blocked.

The stove is on fire and extinguishes as soon as you let go, for the following reasons:1. The battery is dead: The electric ignition device in the gas stove needs to be powered by the battery, so when the battery is exhausted, the gas stove cannot be ignited.

Solution: If you find that there is no electric shock sound of electronic ignition when ignition, please check whether the battery is still charged, and replace it with a new battery if it is not charged.

2. Poor circuit contact: This also belongs to the inability of electrons to ignite, usually due to corrosion in the battery compartment caused by battery leakage, and poor electrode contact causes circuit abnormalities, so that the ignition device is triggered without grinding boy fingering. Workaround:

If the gas stove circuit is not in good contact, the rust needs to be removed and the wiring should be connected accurately.

3. Pipeline blockage: Inferior gas and inferior pipelines will cause pipeline blockage due to impurities, which requires professional maintenance personnel to replace the blocked pipeline and reinstall the interface buckle. Solution: Replace the gas pipeline blindly and seek professional help.