Does the Vantage gas stove turn on automatically when it is ignited?

When the Vantage gas stove is ignited, it automatically turns on the gas. Vantage gas stove, there is a solenoid valve installed at the inlet pipe, when you ignore, the mechanical mechanism will link the solenoid valve switch, so that the solenoid valve can be energized to work, so that the gas is provided normally. When in use, after the gas stove is extinguished due to wind, overflowing water, etc., the ionization probe (i.e., flame-out protection probe) next to the combustion head of the gas stove cannot "pick up" the ionization signal of the flame, so the protection circuit action releases the gas solenoid valve and closes the gas, which protects the safety.

Because of this solenoid valve, and the solenoid valve is always in working condition in the use of the stove, and the power consumption is relatively large, so the dry battery on the stove.

It quickly fails, and if the battery is not charged, the solenoid valve will not work, and of course you will not be able to ignite it with a lighter.

Yes, generally today's gas stoves are electronically ignited, and the gas is turned on at the same time as the ignition, but the valve on the gas tank or natural gas pipeline should be opened first.

The gas stove should be turned on after the fire to prevent gas leakage, and it is best to use the kind with a flame-out protection device, which is very safe.

For the safety of your family, turn off the valves and switches on the gas tank or natural gas pipeline immediately after use or before the family goes out.

Vantage gas stove two ignition methods introduction gas cooker according to the structure of the gas stove is divided into automatic electronic ignition and artificial ignition of the urgent gas stove, today we Beijing Vantage gas stove maintenance to introduce you to these two ignition methods: for the automatic electronic ignition gas open stove correct ignition method.

1. Open the valve in front of the stove, press the half knob inward, then rotate to the left, and the switch will be fully opened when the knob is horizontal.

2. When ignition, the switch should be turned on to the maximum, and then gently rotate the knob to the left according to the needs of the fire after ignition, and adjust the size of the flame.

4. When turning off the fire, close the valve in front of the stove first, turn the gas knob to the right to the hard position, and turn off the gas circuit.

For manual ignition gas stoves, the ignition method is:

First light the fire source (such as matches, etc.), put the fire source to the burner, and then slowly turn on the switch of the gas stove, if it is not lit once, the stove valve should be closed immediately, re-ignited, be sure to remember "fire and gas", not "gas and fire". When the fire is turned off, close the valve in front of the stove first, wait until the fire is extinguished, and then turn off the gas stove switch.

Not necessarily. It depends on whether your household is a liquefied gas pipeline or a liquefied gas tank, the liquefied gas tank is to open every time you use it, and then close the valve after cooking.

Yes. There is a battery valve in the middle of the Vantage gas cooktop (where there is a square hole from the bottom), which will automatically turn on the gas when it is ignited, but after a certain period of time, the spring of the valve may be stuck, and you only need to pat it a few times on the cooktop to reset the spring.

There are several reasons for this

1. Poor circuit contactDue to the longer the use time, the greater the possibility of poor contact, check whether the positive and negative poles of the battery box are rusty, whether the line is in poor contact, if there is a need to remove the rust, and accurately connect the line.

2. Check whether the battery is charged. This is also the direct cause of the flameout, after checking whether there is gas, if there is a problem, it is judged whether it is a battery problem, and when there is no power, you need to replace the battery with a new one.

3. Pipeline blockageCheck whether the pipeline is blocked, once blocked, you need to check the gas outlet valve, usually you can smell the gas stove and the gas stove does not catch fire, it is likely that the gas is blocked, you need to dredge it in time to use it normally.

4. Overvoltage protection. Some gas stoves will have the function of overpressure protection, and they will not start after overpressure, and the pressure reducing valve needs to be replaced.

5. The position of the ignition needle is deviated. The distance between the ignition needle and the fire cover has certain requirements, if the distance deviates too much, it will cause the gas stove to not ignite, the distance between the two is controlled at 4 to 6 mm is the most appropriate, and the fire hole needs to be aligned.

Reason: 1. The corresponding fire hole is blocked by carbon deposit, or the fire hole is not aligned with the feedback needle, and the flame cannot directly burn the feedback needle, and the pulser will think that the flame is extinguished and immediately close the gas source.

2. If the flame is normal, and the thermocouple that plays the feedback role is aging, and the signal strength provided to the pulser is not enough, the pulser will also close the solenoid valve.

3. The feedback loop is not smooth, such as false connection, aging or feedback needle hitting, and the signal cannot be reached.

4. If the power of the automatic gas stove is insufficient, it will also cause the automatic flameout.

Solution: 1: Replace the battery, and then see if the flame in the middle can burn the probe on the broken side, and the probe must be burned to fix the fire. When there is still a point, you can press and hold it for ten seconds, and when you loosen the switch, the probe is the heat induction, and it needs to be burned to fix the fire.

2: To ensure the continuous combustion, the gas stove must ensure the smooth flow of the feedback circuit, the feedback mechanism of the gas stove is mostly set in the place where the flame can be burned directly, when the flame is normal, the feedback loop will provide a continuous gas supply signal to the pulser, otherwise, the pulser will close the solenoid valve.

Answer 1: After the gas stove is turned on, the flame must be burned to the thermocouple, if the fire hole is blocked, it is difficult to achieve this condition, so at this time, the gas stove may automatically turn off.

2. When in use, the gas is originally burned normally, because the thermocouple has been used for a long time and has been aged, and the signal provided to the pulser is not strong, so the pulser will mistakenly think that there is no flame and automatically close the solenoid valve.

3. Abnormalities in the feedback loop, such as virtual connection, lapping, and aging, will cause the signal to weaken and affect the pulser, which will cause the gas stove to go out.

4. If the battery is not replaced regularly, the battery power is insufficient, and the gas stove will automatically turn off.

5. If the damper is in front of the stove, and the back of the stove is biased to both ends of the stove in the middle of the stove, which is used to adjust the outer ring fire and the inner ring fire respectively, try to rotate back and forth to control the air intake, and you can see that there is no red fire. If the air blows the flame away from the ion sensing needle, the gas stove will automatically turn off because the valve is closed.

Daily maintenance work of the gas stove:

1.Electronic ignition is a circuit ignition process, try not to stain the stove with oil stains, need to carry out daily cleaning and maintenance, keep the gas stove clean and hygienic;

2.When the burner is blocked, it should be cleaned in time;

3.When it is found that ignition is difficult, it is necessary to inspect each part and repair it in time.

01 Poor circuit contact.

If the gas stove is used for a long time, it is prone to poor contact, resulting in failure to ignite or automatic flameout.

In this regard, we can check whether the positive and negative poles of the battery box are rusty, and whether the wiring is not in good contact. If there is, remove the rust and connect the lines accurately.

02Check if the battery is charged.

The gas stove battery is dead, which is the direct cause of the flameout.

In this case, we need to check if there is gas on the gas stove. Yes, at all. then determine whether it is a problem with the battery; If the battery is out of charge, replace it with a new one.

03 Pipeline blockage.

Under normal circumstances, the gas stove pipe is blocked, which will also cause the gas stove to fail to ignite or turn off automatically.

For this, we need to check the outlet valve. Normally, if you can smell the gas, but the gas stove does not catch fire, it is likely that the gas is clogged. At this time, we only need to dredge it in time to use it normally.

04 Overvoltage protection.

Nowadays, many gas stove products have added overvoltage protection function in order to ensure safety. When this kind of gas stove is used, once it exceeds the standard pressure, it will not be started again, and it will naturally not ignite.

For this, we only need to replace a pressure reducing valve.

05 Ignition needle position deviation.

When the gas stove is used, there are certain requirements for the distance between the ignition needle and the fire cover. If the distance deviates too much, the gas stove will not catch fire.

<> the reason for the automatic non-stop ignition of the Vantage gas stove may be that the pressure spring of the switch is not elastic, or the elasticity is poor and cannot be returned, or the high-voltage electronic igniter is broken, the contact of the switch is broken, the solenoid valve is not opened, the gas source does not flow to the fire hole, the thermocouple and the solenoid valve do not form a circuit circuit and the flame-out protection device is damaged.

This answer is for Vantage JZT-I10049B gas cooker.

Gas stoves are our most commonly used kitchen appliances and one of the easiest kitchen items to use. As a well-known brand in China, Vantage gas stove is also a topic of great concern to everyone. Below, let's take a look at the ignition method of Vantage gas stove.

1. Automatic ignition gas stove.

The automatic ignition gas stove is the most common gas stove on the market, and its ignition and dismantling method is usually electronic automatic ignition. Vantage gas stoves also use this method.

Steps:1Turn on the gas source and adjust the fire.

2.Press the ignition button on the cooktop. At this point, a "click" will be heard, and a fire will be seen in the burner area.

3.Adjust the amount of firepower and you can use it.

2. Hand-lit gas stove.

A hand-ignited gas stove is an old-fashioned type of gas stove, and its ignition method is usually manual ignition.

Steps:1Pull open the gas valve and select the burner you want to use.

2.Light it with a lighter or match.

3.After the ignition is successful, the amount of firepower can be used to transfer the brigade.

It should be noted that care must be taken when using a hand-lit gas stove to prevent safety accidents.

In summary, the Vantage gas stove adopts the electronic automatic ignition method, which is simple to operate, safe and reliable. The manual ignition method needs to pay attention to the operation method to prevent safety accidents. In order to ensure the safety of you and your family, please be sure to carefully follow the usage specifications to avoid the occurrence of dangerous events such as fires.

Generally speaking, Vantage gas stoves are in the form of electronic ignition, because this can ensure safety and stability during use.

Therefore, we must carry out regular inspection and maintenance of the gas stove, so as to ensure that the electronic power is sufficient and the use effect will be more stable.

Hello, it is a pleasure to serve you and give you the following answers: Reasons:1

It may be that the gas pressure in the gas line is insufficient, causing the flame to not be stable, which leads to flameout. 2.It may be that the temperature of the flame sensor is too high, causing the flame to stall.

3.It may be that the temperature of the flame sensor is too low, and the flame is turned off. Workaround:

1.Check the gas pressure in the quiet bend of the gas pipe, if the pressure is insufficient, you can adjust the gas pressure by adjusting the gas valve. 2.

Check the temperature of the flame sensor, if the temperature is too high or too low, you can adjust the stability of the flame by adjusting the temperature of the flame sensor. Steps:1

Open the gas valve, check the gas pressure in the gas pipeline, if the pressure is insufficient, you can adjust the gas pressure by adjusting the gas valve. 2.Hit the flame sensor, check the temperature of the flame sensor, if the temperature is too high or too low, you can adjust the stability of the flame by adjusting the temperature of the flame sensor.

3.Adjust the temperature of the flame sensor to the correct temperature, and then re-flame to check whether the flame is stable. Personal Experience:

When using Vantage natural gas stove, if you find that the flame keeps igniting and then extinguishes, you can first check whether the gas pressure in the gas pipeline is normal, if the pressure is insufficient, you can adjust the gas pressure by adjusting the gas valve; Then check the temperature of the flame sensor, if the temperature is too high or too low, you can adjust the stability of the flame by adjusting the temperature of the flame sensor. Tips:1

When using a Vantage natural gas stove, the gas pressure in the gas pipeline should be checked regularly to ensure the stability of the flame. 2.When using a Vantage natural gas stove, the temperature of the flame sensor should be checked regularly to ensure the stability of the flame.

The reason is that the fire hole of the gas stove is blocked, so that the gas cannot reach, and it is possible that the thermocouple of the gas stove is aging, which is mostly on the gas stove that has not been maintained for many years, and it may also be because the feedback loop of the gas stove is obstructed. /

Solution: 1. The fire hole is blocked, which is the reason for the most flameout, because in order to burn normally, the flame must be burned to the feedback needle, at this time, if the fire hole is blocked, the fire will be extinguished, the flame is not burned to the feedback needle, the pulser will think that the flame is extinguished, and will automatically turn off the power, which is a fault that encounters the most flameout problems, and the carbon deposits inside can be cleaned up in place.

2. The thermocouple is aging, the gas stove is not maintained in long-term use, the gas stove is easy to age, the flame is normal at the beginning, but as the thermocouple is in an aging state, or directly damaged, it will send an error signal that the pulse is not strong enough, at this time, the pulse will close the solenoid valve, resulting in the phenomenon of extinguishing the fire after a while.

3. The feedback loop is hindered, such as the feedback loop is aging or not lapped firmly, and the signal cannot be sent to the pulser normally, so that it will be automatically extinguished after ignition. The solution is to let the manufacturer check on the spot to see if it is a problem with the feedback loop, find out where the problem is, and the lap is firmly connected or directly replace the new feedback loop to return to normal. Therefore, when you usually use a gas stove, you must remember to maintain and overhaul the gas stove frequently, otherwise there will be various failures.