What should I do if I eat self heating hot pot in the kitchen before I close the lid and the alarm g

Generally, the heating pack contains iron oxide or alumina. Reacting with water releases heat and produces carbon monoxide and carbon dioxide and hydrogen at the same time. The alarm went off because it had detected an excessive carbon monoxide concentration.

I usually turn on the range hood when I eat self-heating hot pot, open the window, and pay attention to ventilation.

When you eat self-heating hot pot in the kitchen, the alarm goes off when the lid is closed, that is, the iron oxide or alumina in the heating bag reacts with water to release heat, and at the same time produces carbon monoxide, carbon dioxide and hydrogen. Because the carbon monoxide concentration was detected to be exceeded, the alarm went off.

Therefore, when eating self-heating hot pot, you should still turn on the range hood, open the window, and pay attention to ventilation. Reduce the concentration of carbon monoxide and carbon dioxide so that it is safer.

Eat too close to the distance.

How do you have an alarm in your kitchen.

I'm also having the same issue, can someone Jetta.

Summary. 1.First of all, you should check if the power supply of the alarm is disconnected to see if it can be turned off.

2.If the power supply is not disconnected, you can try unscrewing the misfire button on the alarm, so that the alarm sound can be stopped. 3.

If the above two methods do not stop the alarm sound, you need to remove the alarm from the roof and put it in a quiet environment to prevent the alarm from sounding again. 4.If the alarm is not working properly, you can contact a professional for repair or replace it with a new one.

Dear, I have sorted out the following steps for you.

1.First of all, you should check whether the power supply of the alarm is disconnected, and you can turn it off to see if the dissipation tank is dissipated. 2.

If the power supply is not disconnected, you can try unscrewing the misfire button on the alarm, so that the alarm sound can be stopped. 3.If the above two methods do not stop the alarm sound, you need to remove the alarm from the roof and put it in a quiet environment to prevent the alarm from sounding again and rushing to the bridge.

4.If the alarm is not working properly, you can contact a professional for repair or replace it with a new one.

Alarm on the roof.

How to do it. I boiled the self-hi pot to call it.

Then you can control the following sounds from Hi Pot.

It also shows from the side that the alarm you bought is very sensitive<>

<>What should I do?

I can't fix the roof.

Your alarm should be able to set volume feedback.

How to set it up.

Pro, there is generally a hail adjustment switch in the alarm, which can adjust the size of the sound sensing distance according to the actual needs. In general, the jujube barrier can be adjusted to three different sensing distances of 10 meters, 25 meters and 50 meters.

You can go up and take a look tomorrow when you have time.

Summary. What to do if the gas alarm alarms 1Do not turn on the lights or light the light.

2.Immediately close the main gas valve and open the window for ventilation; When the indoor gas concentration drops to a safe level, the alarm will stop automatically. 3.

Find out what's causing the gas leak (it could be a leak in a gas line or gas meter). If the cause of the leak is not found, open the main valve. 4.

When unattended, the alarm will automatically close the gas valve at the same time as the alarm to prevent gas leakage; Or automatically turn on the exhaust device to exhaust the gas outside.

Hello dear, happy to answer your questions, the kitchen is boiling since the pot alarm goes off but the alarm is on the roof.

First of all, it is necessary not to ignite, and find the reason for the gas alarm, if it is because of the gas leakage or the high concentration of combustible gas caused by the alarm, at this time the wheel should be stopped as soon as possible, and open the window for ventilation, dilute the concentration of natural gas, when the leakage of natural gas concentration is lower than the natural gas alarm value, it will automatically stop the alarm. If the alarm is misjudged because of the failure of the alarm, or other reasons of the gods, then it is necessary to inspect and repair and solve the technical problem.

What to do if the gas alarm alarms 1Do not turn on the lights or light the light. 2.

Immediately close the main gas valve and open the window for ventilation; When the indoor gas concentration drops to a safe level, the alarm will stop automatically. 3.Find out what's causing the gas leak (it could be a gas pipe mold or gas meter leak).

If the cause of the leak is not found, open the main valve. 4.When unattended, the alarm will automatically close the gas valve at the same time as the alarm to prevent gas leakage; Or automatically open the exhaust device to discharge the gas out of the room.

There is no gas, and there is no hot water.

Hot pot power.

In this case, there is no way to heat it, so you need to pour out the materials inside. It is also possible to use international heating in your own home.

I've done this before. It's not that you can't heat it yourself, it's that you don't use it.

If you eat this kind of hot pot at home, and then suddenly the alarm goes off, it may be because some of your operations have gone wrong.

When the family resigns to make hot pot, the alarm goes off, which is generally caused by the high carbon content of the home, so you must pay attention to the ventilation of the home.

When the alarm goes off, it is a gas alarm, there is a valve, and it can be opened.

What to do, then don't eat it, eat hot pot with a battery stove.

This situation indicates that there is a problem with the automatic ignition system. It is possible that the micro switch of the igniter is short-circuited to see if it is damp or rusty.

There are generally two ways to ignite a gas stove, one is piezoelectric, when ignition, hit the piezoelectric sheet to generate high-voltage electricity and ignite the gas. One is to use the principle of electronics to convert direct current into pulsed high-voltage electricity and ignite the gas, which requires battery power.

In the system of ignition with electric pulse, the gas regulating switch is used to double as the ignition switch, in this case, if the switch point is not set well, the pulse system will be always on state, and this problem can be solved by adjusting the position of the switch.

Use that alcohol wax and go to light it on it.

It means that this is out of order, and it is recommended to use it under maintenance.