How to disassemble the Yager flashlight YG 3260

2. Hold both sides of the monitor and pull it outward, and you must be hard when you pull it out, and pull it out from side to side.

3. Remember not to be in a hurry when pulling it out and pull it slowly to avoid damage.

Precautions for the use of strong light flashlight:

1. Do not shoot light directly into people's eyes, strong light will cause permanent damage to the eyes.

2. It is strictly forbidden to disassemble the lamp head to avoid damage to the reflector or bulb.

3. When the bulb cannot maintain high brightness, please replace the battery for charging when lighting to avoid damage to the battery caused by over-discharge.

Precautions for the maintenance of strong flashlight:

Assuming that your strong flashlight is not used and maintained properly, there will be failures such as the flashlight is always bright, the fire is broken, the switch is not working, the power runs, and the plating falls off. The following are the precautions and specific methods for the use and maintenance of the flashlight:

1. Wipe the flashlight dry with a soft cloth immediately after using it to prevent it from being used in rain or snow or from penetrating moisture and hand sweat. Otherwise, the plating of the flashlight is prone to peeling off or rusting.

2. Do not put the flashlight on the hot kang or next to the stove, and avoid soot fumigation, otherwise the flashlight is prone to run.

3. When moving the flashlight switch, the force must be light and uniform to maintain the elasticity of the spring.

4. When the bottom cover is extinguished, loosen or take out the battery, so as to prevent the bottom cover from breaking the bottom of the battery and flowing out of the slurry.

5. If the silver plating of the glossing bowl is stained and affects the reflection of light, it can be wiped off with clean cotton, and it cannot be fiddled with by hand.

6. When the flashlight is loaded with a battery, it should be put into the paper sleeve together, otherwise it is the easiest to run out. After a new battery has been used for a while, you can switch it to extend the life of the battery.

7. Generally, the battery stops glowing at minus 20 degrees, so pay attention to heat preservation in the cold season.

8. Don't keep exposing the flashlight to the sun when it's not in use, and don't flash back and forth when it's not in use.

I'll teach you, after the base disc is removed. Isn't there only one stand left? Hold both sides of the monitor and call your friend to pull out, and then pull it out must be hard and sway from side to side, rest assured, brother, pull it out is not bad, we are all like this, pay attention to the skill when pulling out, but don't dare to come slowly.

Hello, I'm glad to answer for you, the disassembly method of Yager YGH101 flashlight will be slightly different because of different styles, here are some basic steps that may apply: 1. First, take out the battery to avoid short circuit or other problems caused by the battery during the disassembly process. 2. Next, you can check whether the flashlight housing has threads or fixtures.

If so, it can be unscrewed using the appropriate tool. Some flashlights may have a bonded case, in which case the case needs to be heated with a heat gun or hair dryer and then gently pried open with a confessional tool. 3. It may also take some tricks to disassemble the LED light assembly of the flashlight.

First check if there are fixtures inside the flashlight, such as screws or plug heads, and if so, you need to disassemble them. If not, you can try to gently hold the light cluster with Biming's hand and slowly disassemble it. It should be noted that some flashlight LED light components are soldered to the circuit board, in this case you need to be more careful to avoid damaging the circuit board.

4. If you need to disassemble the circuit board of the flashlight, you need to check whether there are connecting plugs or wires first, and then disassemble these connecting plugs or wires. If you need to disassemble a component on a circuit board, you need to use different tools to remove it depending on the situation. It should be noted that the flashlight disassembly requires great care so as not to damage the components or accessories inside the flashlight.

If you are unsure how to disassemble the flashlight or are having difficulties, it is advisable to seek professional help.

Unable to charge, it is estimated that the charging circuit is broken, or the battery is damaged, or it is possible that there is an open circuit.

If you want to disassemble it, you don't have to, because this cheap plastic flashlight is basically a one-time molding, many of which are not easy to dismantle, if it is still within the warranty period, you can get it to the seller for warranty.

Flashlight: (English: flashlight or torch), referred to as torch, is a hand-held electronic lighting tool.

A typical flashlight has a battery-powered bulb and focusing mirror, and has a handlebar housing for hand-held use. Although a fairly simple design, it was not invented until the late 19th century, as it had to be combined with the invention of the battery and the light bulb. In the early days, because the battery did not have enough power to store electricity, it was called in English"flashlight", meaning a short-lived lamp.