How to replace the pulley under the sliding door yourself

1. For the pulley of disassembling the sliding door, first put the door flat on the ground, and then observe the sliding door, usually there is a wool strip at one end of the door frame, which is directly glued to the door frame.

2. For the wool strip stuck to the door frame, just pull the wool strip apart, tear the wool strip to the second screw hole, the lowest screw hole is the screw hole of the door and window pulley fixing screw, and the upper one is the screw hole that fixes the aluminum alloy frame. Insert a 6mm hexagonal wrench from the round hole.

3. At this time, it is necessary to press the door and window pulley of the sliding door with one hand, use the tool to remove the screw, and then pull out the door and window pulley, which is to remove the door pulley, and the other upper and lower door and window pulleys are the same disassembly method.

4. Push the upper pulley flat into the gap between the screw cap and the inner wall of the door frame. To keep the upper pulley at a distance, a piece of cardboard is sandwiched between the upper edge of the door frame and the plane of the upper pulley. Then tighten the screws.

5. The upper pulley is installed. Remove the cardboard.

If you want to know more about sliding doors, it is recommended to consult Zhengjin doors and windows that have obtained China's green building materials product certification. Zhengjin Doors and Windows is the earliest enterprise in China dedicated to the development of high-end aluminum alloy doors and windows, sun room customization, integrating R&D, production, sales and service. The company takes customer acquisition before opening a store, making profits before investing, and placing orders before starting as its core values, creating a dual-line drainage model, and omni-channel customer acquisition to empower brand development.

Tear down from the top of the door and push the door sliding.

The order of fastening structure is from top to bottom, the upper door frame is disassembled, the fastening nut is found on the door, the upper one is dismantled, and then the door is brought out, and the pulley below can be taken out to replace, pay attention to the wood door is easy to bump and damage, slow down when dismantling, and knock on the demolition with a rubber hammer.

1.Remove the hanging rail screws on both sides of the upper end of the door, pull out the hanging rails to both sides, (there is a card slot at the upper end of the door, and the hanging rail is stuck in the card slot) The door is removed.

2.The two doors are dismantled in the same way. When installing the door, pay attention to the fixed wheel on the ground to clamp into the slot under the door, and then install the slide rail into the card slot at the upper end of the door and screw it.

Remove the positioning pin first, and then push the door to the top, remove the slide Rose, then push the door away, pad, remove the slide Rose at the other end, and the door can be taken down.

Sliding door, this sliding door, you can just get that professional to come and remove it, and they will remove it for you.

Just remove the fixing screws and you're good to go.

1. One person lifts a door so that it is not affected by the top pulley, and one person uses a slender stick such as a screwdriver to gently move the top pulley of the lifted door outward and get out of the position of the door.

2. The door can be lowered when the pulley is separated from the sliding door, and the door without the pulley cannot slide freely.

3. Lift the door again and drag the lower part of it outward, the door needs to be installed back after being removed, and the steps are the opposite of the steps removed.

4. Pay attention to one point, don't push the pulley back to the iron groove at the top of the door, and you're done.

The sliding doors are wheeled to adjust the hanging screws to your desired position. That's it.

The adjustment part of the sliding door should be on the wheel below, there are screws on it, and the height and low degree are required, and it can be screwed directly. The general sliding door is installed by professionals in the store, if you can't get it right, you can go to the store to consult, ask them to adjust.

Dear, I'm glad to answer for you: how to disassemble the upper pulley sliding door is as follows: 1. If you want to disassemble the door on the slide rail, it is best for two people to cooperate, and one person will lift the door, and it will not be affected by the effect of the pulley.

In addition, a person should prepare a screwdriver and flick the top pulley of the lifting door leaf outwards to break away from the door frame. 2. Wait until it is detached, and then put down the door leaf, without the door of the pulley device, it will be easier to disassemble. All we need to do is lift the door and drag the lower half outwards to be able to disassemble it.

3. If you want to install it later, it is also relatively simple, because it is the opposite of the steps of disassembly. Dial the pulley back into the iron groove, two people cooperate, one person clicks into the pulley device, and the other person pushes it up, and it can be installed back.

Here's how:

1. First, install the upper track; It is necessary to place the track in the middle of the door sleeve, so carefully measure the dimensions of the 2 sides first.

2. After careful positioning and measurement, reassemble the five plates of the drawer, tighten the screws, and there are card slots on the drawer panel. After processing, place the drawer on the installed drawer, so that you can use an electric drill to adjust the position of the nail hole to match, and be careful not to shift when drilling.

3. After drilling holes on both sides, fix them with self-tapping screws, then drill holes in the middle, and then install screws with screwdrivers.

4. Then install the lower track installation, and wipe the bottom of the wardrobe first.

5. Position positioning of the lower rail, put the sliding door in the upper and lower tracks first, adjust the position, so that the sliding door can achieve the best sliding effect, and then follow the installation method of the upper rail, drill and then fix. Then fix the position of the lower rail, and clean the inner layer of the track with a brush.

6. Sliding door installation. First of all, lift the door gently to let the upper pulley of the door enter the upper track, and then lift the sliding door with one hand, and pull the sliding wheel with the other hand, so that the lower wheel can smoothly enter the lower track, and it is best to complete it with two people.

1. First of all, remove the sliding door and put it aside;

2. After removing it, we can see that there is a wool strip stuck to the door frame at the bottom of the sliding door;

3. Tear the strip on the door frame a little to reveal a hole;

5. It can be seen in the figure that the screws have rusted;

6. Immediately afterwards, press the pulley of the sliding door with the left hand, match the screw hole with the screw, and insert the screw hole into the screw hole with the right hand;

7. At this time, the pulley is replaced.

How to replace the sliding door pulley is broken, simple and easy to learn.

How to repair and replace the rusty pulley of the sliding door at home? In fact, the process is very simple, just look at it.

If you have tools, it is more convenient, if you don't have tools, you can only use your hands, first push the wheel in the direction of the mullion, and then use the other hand to stick into the mullion from the big mouth of the mullion and start to loosen the screw, which is basically the same when loading.

1. How to change the pulley under the sliding door.

1. Remove the sliding door first, then you need to hold the bottom of the door and lift it up; 2. Place the sliding door flat on the ground and tear the wool top until the position of the second screw hole; 3. Unscrew the screws of the locking pulley and remove the slower pulley; 4. Replace it with a new pulley, and then install it according to the previous disassembly method.

Second, how to maintain the sliding door.

1. After the sliding door has been used for a long time, more stains will accumulate on its surface, which will affect the appearance. Therefore, it is necessary to clean the sliding door regularly and wipe it with a soft cloth to prevent scratches on the surface of the sliding door. And usually do not hit the sliding door with heavy objects to avoid damage.

2. If there are serious stains on the sliding door and it is difficult to wipe it off, you can choose to clean the sliding door with a neutral or special detergent, and then wipe it off with a dry rag after the stains are disposed of. If there is a slight scratch, cover it with a toothbrush.

3. The frame of the sliding door is usually made of metal, so it can be wiped with a cotton rag when wiping it at ordinary times. If you use water to wipe it, you need to dry the water on the surface in time, otherwise it is easy to corrode and affect the overall appearance.

4. The track of the sliding door is a place where dust is easy to accumulate, if it is not only the first condition, it is easy to cause the pulley to be stuck, so that the door cannot be opened and closed normally. If the pulley cannot be used smoothly, a few drops of oil can be applied to the surface of the pulley to reduce resistance.

About how to change the pulley under the sliding door, and how to maintain the sliding door, it will be introduced here, do you understand? If there is a problem with the pulley of the sliding door, it is necessary to repair it in time, otherwise it will affect the later use and bring unnecessary trouble.

1. First of all, remove the sliding door and put it aside;

2. After unloading, we can see that there is a wool strip at the bottom of the sliding door glued to the orange frame of the door;

3. Tear the strip on the door frame a little to reveal a hole;

5. It can be seen in the figure that the screws have rusted;

6. Immediately afterwards, press the pulley of the sliding door with the left hand, match the screw hole with the screw, and insert the screw hole into the screw hole with the right hand;

7. At this time, the pulley is replaced.