How to use the bull socket? How to wire the bull socket

When installing sockets, many families feel that they are too high to be unsightly, so they will install them in a low hidden position. However, Dr. Xia Dong of the Institute of Electrical Engineering of the Chinese Academy of Sciences said that it is easy to let water splash into the socket when mopping the floor, which can lead to leakage accidents. According to industry regulations, the distance between the exposed socket and the ground should not be less than one meter; The concealed socket should not be less than a meter from the ground.

The sockets in the kitchen and bathroom should be more than one meter above the ground, and the sockets in the air conditioner should be at least 2 meters or more.

The power leads must use a copper wire cross-section. If you live in an old house, be sure to replace the original aluminum wire with copper wire. Because the aluminum wire is very easy to oxidize, the joint is easy to ignite.

Surveys have shown that the incidence of electrical fires in residential buildings using aluminum wires is dozens of times that of copper wires. In addition, many families for the sake of beauty, will use slotted buried wire, dark pipe laying method, Xia Dong reminded, wiring must follow the principle of "live wire into the switch, zero line into the lamp head", but also in the socket leakage protection device.

Multi-hole socket, that is, the jack can be compatible with two or three poles at the same time, and even the British standard, American standard, European standard and other sockets with non-daily use plugs. However, due to the large jack of this kind of socket, the contact area between the socket connector and the electrical plug is too small, which is easy to overheat the contact piece and lead to fire accidents. The two-core socket is easier to distinguish from the appearance, where there is a three-pole jack on the plug board, but there are only two bolts on the plug of the socket itself, which are two-core problem sockets.

This kind of socket lacks a ground wire, in the process of use, once an insulating part inside the appliance is damaged, the current will be spread over the entire surface of the appliance, because the current can not be introduced into the ground through the two-core socket, it is easy to cause electric shock accidents.

The above is the relevant content about the misunderstanding of the use of bull brand sockets. In fact, we will often encounter some misunderstandings in the process of using sockets in our lives. Therefore, this time I will introduce you to the misunderstanding of the use of bull brand sockets, as long as you remember that you will not make it again in the future.

If you want to use the manual of this wireless socket, you can follow the instructions to operate, because it is a wireless socket, as long as it is connected to the network, it can be charged, and it does not need to be plugged in.

Tools Raw Materials:

Screwdriver tool.

1. Before getting a socket, first check whether the socket is intact or damaged, and disassemble it only after checking that it is not damaged.

2. Now the socket is disassembled, generally a special screwdriver is required to disassemble, after dismantling, you can see the terminal, the terminal definition is L n and the earth three wires, according to the rules of the wire press.

3. After pressing the wire, it is not completed, and there is a bayonet for fixing the wiring harness, here the bayonet is pressed directly, not too tight and not too loose.

4. Check that there is no problem with the circuit, you can install the shell of the socket, and then test the shell for safety reasons.

5. Power on the socket, and then press the switch button of the socket, under normal circumstances, the indicator light of the socket will be on, if it is not lit, the connection is not successful, and you need to disassemble it to check the wiring.

6. If the indicator light is lit, it means that the connection is successful, if you need further confirmation, use a multimeter to measure the voltage to see if the voltage is normal, if it is normal, you can use it with confidence.

Do the math how much it will cost you to renovate your home

According to Qeeka Home experts, the purchase of switch and socket products, will generally give priority to brand products, not only because the brand style is good-looking, but also because of the quality problems, because the socket needs to be energized, if the quality can not be guaranteed, not only the service life is short, but also easy to appear a variety of safety hazards, so when buying will choose Bull, Siemens, Legrand and other big brands to produce, so how to wire the bull socket? Let's take a look with Qeeka Home experts.

1. How to wire the bull socket.

First of all, pull down the power switch, disconnect the power supply, operate and package the construction safety; Then disassemble the power cable, you can see three wires of different colors, and distinguish the neutral wire, live wire and ground wire; Then connect the red wire with the socket L binding post, the blue wire with the socket N binding post, and the yellow wire with the socket E binding post; Finally, the socket panel can be installed.

Second, what are the skills for choosing a socket.

1. Select**.

To buy socket products, you must not buy products made of fake and shoddy materials, there will be great potential safety hazards, and the service life is not guaranteed, and these products are usually produced in some small manufacturers of the Destruction Bureau, so it is necessary to choose large-scale jack products, which are more quality assurance.

2. Pick the material.

Judging the advantages and disadvantages of the socket material can start from three places, namely the panel material, the conductor material and the base material, the panel material is the most obvious, requiring a smooth and smooth appearance, and there will be no bubbles, scratches, stains, etc., followed by the conductor material, usually the fiber is mainly copper, which has a more conductive effect. Finally, there are two options of plastic and metal materials, generally based on plastic materials, but the base of cold-rolled steel plate material is more durable.

Summary: The above is about how to wire the bull socket, and what are the tips for buying the socket, I hope the content shared can give you some reference, if you want to know more about the relevant knowledge, you can **** Qeeka Home to consult.

Enter the area and get the decoration for free**].

The bull socket wiring diagram is as follows:

When connecting the line, connect the red wire (live wire) and the blue wire (neutral wire) to the terminal post L and N respectively, and the yellow-green two-color wire is connected to the socket terminal post N, and then connect the socket L binding post and the switch terminal post with a broken wire, and then connect to the switch terminal L with another wire from the bulb.

If you want to switch the control socket, you should connect L11 or L12 to the switch, then connect the live wire to L10, and connect the neutral wire to the socket N. If the socket is not switched, the L connection of the socket is connected to the live wire N to the neutral wire, the L10 of the switch is connected to the live wire, and the L11 and L12 are connected to the control line control light or other sockets of the wire box.

1. There are three wiring exposed holes on the bull five-hole switch, which are L live wire, N neutral wire, and E ground wire. Remove the insulating skin at 2 cm at the end of the wire to expose the copper wire head. 2. The two wire heads are twisted together, stretched into the hole, and the screws are installed.

If the thread is too long, cut some of it. 3. Connect the switch live wire and the circuit live wire into the same switch jack, insert the neutral wire into the n hole, and insert the ground wire into the ground wire hole.

When the bull socket is connected to the line, you will see that there are three colors of wires in the socket, of which the red wire is the live wire, the blue wire is the neutral wire, and the yellow-green wire is the ground wire. After distinguishing the three wires, connect the live wire to the L terminal post in the socket row, and connect the neutral wire to the N binding post.

The bull socket connection line must be connected correctly, you can distinguish the zero wire, live wire and ground wire according to the color according to the above content, if the connection is wrong, then the plug-in board will not be able to use normally, and there may even be potential safety hazards.

When wiring, you must pay attention to safety, first of all, turn off the power at home, do not get water on your hands, and wear insulating gloves. If you find that the wire is damaged, you must pay attention to it, do not ignore it, and it is best to replace the wire.

If it is a socket in the kitchen and bathroom space, it is recommended to install a layer of protective cover on the outside of the socket when installing, which can effectively prevent oil stains and water vapor from entering the socket, and can avoid problems such as short circuit in the socket.

Introduction to the advantages of bull switch plugging and balancing only matching seats:

1. The socket is made of imported PC material.

The flame retardant capacity of the socket is very important for the safety of the socket, and the bull socket uses imported PC flame retardant materials to solve the problem of cracking and fading of the socket, which is more safe and reliable than the general socket.

2. Socket lightning protection design.

Bull socket is the first enterprise in China to introduce the anti-lightning technology to the wall socket, which realizes the protection function of blocking the high voltage, strong current and ultra-high temperature generated by lightning, and effectively protects the safety of home appliances and family members.

3. The bull switch socket has a long service life.

The service life of the socket switch is directly related to the bad switch, according to the test, the bull socket can reach the service life of the switch 10,000 times and more than 5,000 times of plugging and unplugging, and the quality of the bull socket can stand the test.

<> switch control lamp, live wire to socket L, zero slag wire to socket N, ground wire to socket "ground", connect socket L and switch L10, L11 to connect the lamp control line to the positive pole of the lamp, socket N to the negative pole of the electric blind banquet lamp. Grinding and buried.

Bull socket wiring party resale method.

1.Determine the circuit type.

Before proceeding with the bull socket wiring, it is necessary to confirm the circuit type. The bull socket usually has two circuits, 220V and 380V, which need to be selected according to the actual situation. In addition, it is also necessary to confirm the number of phases of the circuit, which is generally divided into single-phase and three-phase, which needs to be determined according to the leakage travel electrical equipment.

2.Prepare tools and materials.

Tools and materials need to be prepared before wiring, including flat screwdrivers, wire pliers, wire cutters, insulating tape, etc., as well as the required wires, plugs, and bull sockets.

3.Make the wiring.

Start wiring the bull socket. Start by removing the cord from the plug and cutting off about 1 cm of wire sheath at the end of the wire. Then insert the stripped copper wire into the corresponding position in the socket and clamp the wire with a wire plier. Then connect the plug to the socket and plug it in tightly.

4.Grounding treatment.

In order to ensure safety, the grounding of the socket must be done well. This can be achieved by connecting the bull socket ground wire with the earth wire at home. The grounding wire can be fastened to the screw on the back of the plug or grounded along with the plug wire.

5.Check if the line is correct.

Be sure to check the line after you finish wiring. First of all, check whether the wiring is correct and whether it is fastened firmly. Second, confirm that the plug and socket connection is stable. Finally, it is also necessary to check whether the wires have been bitten or frayed, and that the surface of the socket is clean.

6.Pay attention to safety and suspicion.

Be sure to pay attention to safety during the wiring of the bull socket. First of all, it is necessary to ensure that the power is cut off to avoid the occurrence of electric shock accidents. Secondly, after wiring, all tools and materials should be cleaned up to avoid tripping and electric shock.

At the same time, children should also stay away from the family to avoid accidental injuries.

7.Test the circuit.

Circuit testing is carried out after wiring is completed. You can use professional electrical instruments to test the wiring to check whether the current and voltage are normal, and whether the grounding is good. If the test result is abnormal, you need to troubleshoot and fix it in a timely manner.

8.Seek professional help.

If you are not familiar with the bull socket wiring, or encounter a more complex situation, it is recommended to seek professional help. This not only ensures the correct and safe wiring, but also saves time and effort.

Without a switch, you can press the left zero right fire in the indirect ground. Just pick it up.

As we all know, the most important thing in house decoration is the renovation of water and electricity, which is a very strict work concession banquet, if there is a problem, the later maintenance is very troublesome. The sockets and switches of the bull are very famous, and Bihe is one of the preferred brands for the majority of consumers, so how to wire the bull socket? What problems should be paid attention to when installing sockets?

Start by turning off the main power switch and get the tools you need. Usually the red line refers to the live line, and the blue line represents the zero line. Connect the red wire to the L end of the bull socket binding post and the blue wire to the n end of the binding post.

Next, put the socket against the wall, adjust the orientation, and finally fix it with screws.

What problems should be paid attention to when installing the socket.

1. Calculate the number of switches and sockets required to be installed.

Before installation, you should calculate the total number of sockets and switches, at least one five-hole socket on each wall in the bedroom, and the living room needs to install broadband and TV and other equipment, and the socket needs to be reserved more. Socket switches in the kitchen and bathroom are also essential, and for ease of use, there should be more sockets than less. In addition, the sockets used in different areas are different, for example, the bathroom and kitchen are humid, so you should choose a socket with moisture-proof function.

2. Install according to the usage habits.

It should be combined with the living habits of the owner, basically people like to use the right hand to open the switch, then the socket is suitable for installation on the left side of the door. If you are left-handed, install it on the right side of the gate. It is recommended to install dual control switches in the bedroom and hallway for more convenient use.

In addition, the distance between the socket switches should be considered when installing, and each socket should be kept at least 50 centimeters apart.

3. Pay attention to the installation height.

The height needs to be combined with the height of the owner and the convenience of use, if it is the socket of the desktop air conditioner, it should be about one meter five from the ground, if it is a cabinet air conditioner, it can be about 30 cm from the ground, and the installation height of the socket of different electrical appliances is different.

Article summary: The above is the relevant content of how to connect the bull socket to the silver wire and what problems should be paid attention to when installing the socket, I hope it can help some friends in need.