When decorating a new house, how to position the water and electricity at home?

When decorating a new house, the easiest way to locate the water and electricity in the home is to locate it according to the overall layoutFor example, when we coordinate the overall layout, the bathroom is in**bedroom**, the kitchen is in**, the living room is in**, and all the electrical appliances to be installed in these places, most of the locations we need to know in mind, in order to accurately locate the location of water and electricity, and then when we do water and electricity, we can be handy, and we can minimize the probability of rework. So before we do the water and electricity change, we should think of the following points:

1. Several electrical appliances should be installed in the living room

First of all, we should consider how many kinds of appliances are installed in the living room? Commonly used is television, refrigerator, air conditioner, in addition to should be reserved 1 2 jacks to expand some sockets, for example, after the decoration, we suddenly want to install an electric heating gap system, then at this time may need an expansion jack to use, of course, this is just an example, if there are other similar appliances, the same is true.

2. The layout of the bathroom should be reasonable

Secondly, the layout of the bathroom must be reasonable, because the water and electricity changes are mainly for the bathroom and kitchen, and the bathroom is the mainstay, so the sewer aspect, I believe you can be very easy to locate, because the toilet sewer is usually only three important points, the first is the sewer of the toilet, the second is the drain of the floor drain, and the third is the sewer of the wash basin, so in addition to these three, the electrical socket is recommended to be installed on our 4 weeks of the wall, because it is too low, There is a risk of contact with water sources.

3. Leave a few more electric jacks in the bedroom

Finally, we need to pay attention to the fact that we can leave a few more electrical jacks in the bedroom, which is due to the rapid development of our times, and the products developed by high-tech are generally related to electrical appliances, so if we want to keep pace with the times, we should try to leave a few more electrical jacks in the bedroom, for example, we are likely to buy a few particularly advanced household appliances to be placed in the bedroom in the near future.

We should have a comprehensive understanding of the entire water and electricity layout construction drawings of the house decoration, and the increase in the capacity of the line must refer to the actual electricity situation, which should be paid attention to.

The positioning of water and electricity at home should first choose a relatively safe line, and choose a regular master to install, so as to achieve the effect of positioning.

If you want to locate the water and electricity at home, the best thing to do is to choose the kind of living standard that suits you, which is beyond your financial range, otherwise you will feel very stressed.

There are four precautions for water and electricity in the decoration of <> new house, which are to plan the number of water and electricity sockets in the new house, the switch and socket are designed on the same level, the kitchen water and electricity are positioned, and the water and electricity test is carried out after the decoration is completed.

When decorating a new house, it is necessary to plan the location of the water and electricity socket first, and mark it well, and pay attention to the design of the socket and the water and electricity switch on a horizontal line, so that the socket in the room has a certain order and will not appear disorganized. The positioning of water and electricity in the kitchen should be reasonably designed, and water and electricity should be avoided as much as possible. Finally, after the renovation is completed, the water and electricity tests are carried out to ensure that the water and electricity lines can be used normally.

1. Prepare a marker pen and tape measure for backup before positioning, usually the electrician will carry it with him, but also just in case. After locating with the electrician, be sure to go to the site again to confirm and pay attention to the location of each electrical appliance, such as the air conditioner. 2. Hydropower positioning is to determine the location of the switch socket and the location of the waterway interface of the whole house according to your needs, and the plumber should draw the direction of the water pipe and wire on the wall according to the position of the switch socket and faucet, that is, the layout line.

3. Before the positioning of water and electricity, it is best to ask professionals to test the pressure of the water pipes of the new house, and the property company should do a 24-hour closed water test and check the circuit at the same time.

First of all, we should separate the various positions of the circuit to prevent a problem with a circuit, turn off the lights at home, and at the same time should make the bathroom and kitchen waterproof, it will be more convenient to use later, and there is no worry.

When decorating, we must plan where to be, where to be, and then we should reserve a few more plugs in normal times, so that we can move home appliances in the future. Then the water and electricity must go on the switch, if the water and electricity and wires are drawn on the wall, the direction must be the layout of the line.

Home decoration and installation of water and electricity, the first thing to consider is safety, in addition, what else should be paid attention to? In fact, the decoration of hydropower positioning is a very important matter, but there are many people do not know very well, today I will give you a popularization of how to locate the decoration of hydropower and decoration, what to pay attention to in the positioning of decoration and hydropower, I hope to help you understand the positioning of hydropower.

First, how to position the decoration of water and electricity.

Hydropower positioning is to locate the position of the switch and socket installation, and the hydropower positioning has the positioning of the waterway and the positioning of the circuit

1. Positioning of waterways.

Regarding the positioning of the water pipes, if you are in the bathroom, the wash basin is 45 cm from the floor. In addition, the shower is about 80 120 cm from the ground, and you can choose the height according to your habits.

2. Positioning of the circuit.

As for the positioning of the electrical socket, it is generally necessary to reach 120 130 cm from the ground, and it should be installed on the side of the door lock, about 20 cm from the door frame. In the master bedroom, a dual-control switch should be installed, that is to say, an auspicious chain should be installed at the door, and a bedside table should be installed.

Reminder: When the socket potential is combined, different spaces and different needs, such as reserving two sockets on the video wall, the height from the ground is about 60 cm. In addition, there are some electrical appliances in the kitchen or bathroom, the height of the range hood is about 200 230 cm, and the water heater is 15 cm higher than the water inlet.

Second, what should be paid attention to in the positioning of decoration water and electricity.

1. Attention needs to be paid to on-site positioning.

When the site is located, it is operated by the plumber masters, and the masters should bring a tape measure and a marker, make a mark, and verify it on the spot, draw a line on the wall, and be able to determine the direction and location of the slotting.

2. Attention needs to be paid to hydropower positioning.

The positioning of water and electricity is not only decided by the owners and hydropower workers, but also the sanitary ware merchants, cabinet merchants, ceiling merchants, electrical appliances merchants, etc., are invited to the scene to discuss the direction of water and circuits. Generally speaking, when carrying out water and electricity planning, the owner should have already ordered the design of cabinets, ceilings, etc., so the design of water and circuits must be planned according to the water and electricity diagram required by the business. If the positioning of water and electricity is planned in the early chain, it is easy to have some problems when installing cabinets and sanitary ware in the later stage.

Reminder: When it comes to hydropower positioning, you are afraid of missing some items, so when considering water and circuit planning, you should plan for the long term. The water and electricity wiring is mainly planned according to the needs of the owners of the sheds, so the owners must give detailed suggestions according to their daily habits at home.

The above is how to position the decoration water and electricity shared by the hunting network for you, and what relevant information should be paid attention to in the positioning of the decoration water and electricity, I hope it will help you. Hunting network, China's well-known large-scale decoration square platform, if you have any questions about water and electricity decoration, you are welcome to consult.

New house decoration, gas or electric water heater, water heater brand, specification, size. If the water heater uses electricity, it is best to provide the specific model to check the size. Determine if the shower rod is adjustable.

If it is not adjustable, determine the height of the shower rod to facilitate the positioning of the mixing valve outlet. If it is adjustable, it can be done according to the national standard height. If it's a concealed shower, be sure to buy a shower in advance and use it when you start working.

The decoration of the new house is integrated, or the ceiling of calcium silicate board or sauna board. whether the integrated heating appliance is warm or warm; If you hang a calcium silicate board or sauna board on the ceiling, what is the function of the bath bomb, which is related to the problem of wire retention during circuit transformation. For the decoration of the new house, determine the cabinet water and electricity drawings, and submit them to the water and electricity location personnel on the day of entry.

After the water and electricity decoration is located, you must prepare a tape measure and marker, and then go to the site to inspect and pay attention to the reserved position of each electrical appliance. The water and electricity layout lines must be drawn in the corresponding positions according to the hydropower diagram. The cost of hydropower project renovation cannot be settled at one time, and should be paid after passing the inspection.

Before decorating the positioning of water and electricity, it is necessary to carry out the water pipe pressure test and closed water test to check whether the circuit meets the requirements, whether the socket has a grounding wire, and whether the circuit is equal. When locating hydropower, be sure to ask relevant professionals and plumbers to discuss the positioning and distribution of hydropower, and also consider the installation of electric water heaters and gas water heaters. Long-term interests should be considered when positioning water and electricity, and more sockets should be reserved in the kitchen for emergency use, and more sockets should be reserved for the TV background wall to avoid the trouble caused by insufficient sockets in the later stage.

When installing dining room lights, be sure to pay attention to the placement of the dining table and the position of the wall lamp next to the bed in the bedroom. The position, height and spacing of some sockets should be calculated to avoid socket blockage.

It is best to install bedroom ceiling lights with dual control, one next to the bed and one next to the door, so that it will be more convenient to get up and turn on the lights in winter. When installing kitchen lights, you can install a small light at the cutting area, and a spotlight can also be installed above the gas stove and sink, so that you can have a clear line of sight when cooking at night, and it is convenient to cook. When installing the circuit, be sure to consider the location of the air conditioner, and the power supply should be moved as close to the air conditioner as possible, so that there will not be a large number of power cords leaking out, which will affect the appearance.

In addition, all air conditioning outlets should be equipped with switches so that there is no need to risk unplugging. To turn off the air conditioner, simply press the switch next to the outlet. Except for special requirements such as refrigerators and air conditioners, the switches in each room should be in the same horizontal position.

In order to use electricity safely, it is best to color the neutral line, live wire, and control line.

For the installation of living room lamps, it should be simpler and convenient for cleaning later. When positioning hydropower, we should first look at the lamps, as well as the installation position and location of the switch and socket, and ask a professional hydropower master to help design the circuit layout. The water pipes in the main sanitary room should follow the principle from top to bottom, which is more convenient for later maintenance.

Moreover, the hot and cold water pipes should be planned on a parallel line according to the position of the hot left and the cold right, which is the habit of most people. An inspection port should be reserved on the toilet drain pipe, which can be inspected and repaired if there is a problem, and a check port should be configured for the sanitary ware part.

1.Don't just pursue horizontal and vertical wires, once there is a problem to change the wire, you can't pull it out at all. 2.

Don't use 16 pipes for wire pipes, it's too thin and easy to get stuck. With a diameter of 20 tubes, the threading is smooth, and the wire will not be damaged when changing the wire. 3.

Kitchens and bathrooms do not need to use flat wires, use 4 flat wires so that they will not be overloaded, and use 6 flat wires for instantaneous water heaters. 4.Do not make a right-angle bend in the drain pipe, try to make a 45-degree drain bend.

1. The waterway circuit should be disclosed, and the location should be found at the construction site, and the number of sockets should be planned. 2. Mark the location of the switch socket and water outlet, and then arrange the connection path of the water pipe and wire. 3. Let the switches and sockets of the whole house be on the same level.

4. After the electrician is positioned, it needs to be reviewed on site to ensure that the position of air conditioning and other electrical appliances is appropriate. 5. Carry out water pipe pressure test and electricity test to ensure the smooth flow of water and electricity.

1. The distance between the two sockets should not exceed 3 meters, why? Because the length of the power cord of most household appliances is about one meter, when the appliance is between two sockets, the left socket can not reach the right socket, so as to avoid the situation of using the plug board to transfer. But there is one point, please don't misunderstand, there are some places at home that must use the power strip, here is mainly to say not to use the plug-in board to extend the electrical power cord, otherwise when the electrical power cord has a section can not be blocked by the furniture, the power cord on the ground arches and warped looks unsightly, and it is easy to mix feet, and it is a safety hazard when there are elderly and children at home.

2. Under the condition of conditions, the socket is best set in the corner of a room (preferably diagonally), so that the electrical appliances on both sides of the wall near the corner can be used to this socket, so as to avoid pulling the "rifling wire" when using household appliances in the future. 3、Now it is very popular to mount wall-mounted TVs, so it is necessary to pre-bury a 50PVC pipe in the background of the TV, so that the socket line of the TV and some DV cables and audio lines can pass through from there、This will not affect the appearance。

When home decoration of water and electricity, the first item is the disclosure of water and electricity, on-site positioning. Prepare a mark and tape measure for backup before positioning, under normal circumstances, the plumber master will carry it with him. Just in case.

Then according to your own preferences, communicate with the installation master. There is also a socket left next to the toilet in the bathroom, which can be installed with a smart toilet. According to your own ideas, you can coordinate with the installation master.

Be sure to say it thoroughly, otherwise it will affect the entire installation effect.