How should built in drum washing machines, faucets and sewer pipes be reserved, and what should I pa

Built-in drum washing machine.

Faucets and sewer pipes should be reserved for about 1 meter, and there are quality aspects to pay attention to.

1.Whether to choose a single or double tube for the washing machine style, whether to choose a wave wheel or a drum. Depending on the style of the washing machine, the location of the water inlet is also different. Generally speaking, the capacity and height of the washing machine are high, and the larger the capacity, the higher the height of the washing machine. For floor drains.

Location, the installation of a washing machine requires not only confirming the location of the inlet pipe, but also the location of the drain pipe. Only if these problems are confirmed in advance, the reserved faucet position is suitable for the washing machine.

2.Many people like to plug the drain of the washing machine directly into the floor drain, but there is a risk that the drain of the washing machine will come off the floor drain. If not detected in time, the water will flow to the ground or even downstairs.

In addition, some floor drains are relatively slow to drain and cannot meet the needs of the washing machine's drainage speed. Therefore, when using the washing machine, it may spill out of the floor drain. By waterproofing, we mean that the room itself is not waterproof.

If the room is already waterproofed, there is no need to waterproof the washing machine separately.

3.If the cabinet where the washing machine is located has a countertop, it is recommended to place the washing machine socket above the countertop. In the future, make a hole in the table and go through the plug. Installed in the built-in area of the air humidity near the washing machine.

It is very high, it is easy to affect the service life of the socket, and it is inconvenient to unplug and plug in. Convenient with switch. The washing machine cannot be used 24 hours a day.

Power can be cut off when not in use. It's too much trouble to unplug often. If you bring a switch, it will be easier to control.

4.Remove the drain pipe of the washing machine and place it in a supported position. Note that one end of the drain pipe of the washing machine is installed at the drain outlet and the other end is installed at the drain outlet of the washing machine.

When installing, please check whether the position dimensions are consistent. Then insert the sewer into the reserved outlet of the washing machine base until it fits the length of the washing machine drain. Then install the drain, tighten the screws, and then install and fix the bottom plate.

Finally, move the washing machine to the correct position and turn it on.

When placing a built-in drum washing machine, the size of the faucet and drain pipe should be the same as the standard size, and enough water pipes should be reserved to prevent clogging.

The drum washing machine that I tried that day should be measured in size when decorating, so as not to bring unnecessary trouble after buying the washing machine.

Take Haier washing machines as an example, drum washing machines.

The correct installation method of the drain pipe is roughly divided into four steps, and the specific operation steps are as follows:

1. First take out the drain pipe of the washing machine and place it in the matching position, pay attention to one end of the drain pipe of the washing machine is installed at the drain port, and the other end is installed at the drain port of the washing machine.

2. Then plug the sewer pipe into the reserved opening of the washing machine base until it fits the length of the washing machine drain pipe.

3. After installing the drain pipe properly, tighten the screws, and then install and fix the bottom plate.

4. Finally, move the washing machine to a suitable position, turn on the power and use it.

Precautions for installation and use of washing machines:

1. The lower drain port must be higher than the drain pipe during installation, otherwise the water may remain in the drain pipe.

2. The location of the washing machine is best in a relatively ventilated and dry place.

3. After washing the clothes, take them out to dry immediately, and do not stuff them in it for a long time.

4. After washing clothes, the water should be fully drained and the lid should be opened to dry to avoid residual water in the machine and form a breeding ground for microorganisms.

It should be noted that this answer is applicable to most brands of washing machine models such as Midea, Gree, and Haier.

Summary. Drum washing machine reserved water and electricity location Hello dear, 1. Drum washing machine water inlet pipe decoration reserved faucet method: 1. First of all, it is best to preliminarily select the model of the drum washing machine you need, and study the size and size.

If you can, of course it's better to have the faucet close to the top of the inlet end of the washing machine. 2. In order to achieve the best use of family space, this design should be based on space as the primary consideration. How to place the washing machine to save space and use space is the first thing you should consider.

3. After considering the spatial distribution, decide the position of the faucet. The faucet position is best than the size of the washing machine, if allowed. In case you need to replace a bigger washing machine in the next few years.

4. It is better to place the drum washing machine on the side of the washing machine. The height is generally around 1100 1300cm. Second, the height of the drum washing machine socket is reserved according to the size of your washing machine, generally placed at 1100mm from the ground, according to the requirements of the national power installation, the general switch plug-in board should be meters from the ground.

This distance is for the safety of children. In order to look good, the current decoration is very low, which is actually wrong. So now the plug-in board on the market is equipped with a protective sheet, and the finger plug into the jack will not be contacted, but there are exceptions.

Hello, I have seen your question, and I am sorting out the answer, please wait for a while Hello dear, first, the drum washing machine inlet pipe decoration reserved faucet method: 1. First of all, it is best to preliminarily select the model of the drum washing machine you need, and study the size and size. If you can, of course it's better to have the faucet close to the top of the inlet end of the washing machine.

2. In order to achieve the best use of family space, this design should be based on space as the primary consideration. How to place the washing machine to save space and use space is the first thing you should consider. 3. After considering the spatial distribution, decide the position of the faucet.

The faucet position is best than the size of the washing machine, if allowed. In case you need to replace a bigger washing machine in the next few years. 4. It is better to place the drum washing machine on the side of the washing machine.

The height is generally around 1100 1300cm. Second, the height of the drum washing machine socket is reserved according to the size of your washing machine, generally placed at 1100mm from the ground, according to the requirements of the national power installation, the general switch plug-in board should be meters from the ground. This distance is for the safety of children.

In order to look good, the current decoration is very low, which is actually wrong. So now the plug-in board on the market is equipped with a protective sheet, and the finger plug into the jack will not be contacted, but there are exceptions. Hope it helps.

The upper water pipe, also known as the water inlet pipe, is generally in the upper part of the back of the machine.

The drain pipe is also in the back, but there is only one outlet, as for the upper and lower drainage, as long as the drainage pipe is first snapped into the closed celery buckle according to the requirements, and it is installed in an inverted U-shape, and then you will listen to it.

The location of the inlet and drain pipes is shown in the diagram. It has been clearly marked on the diagram.

The upper and lower drains of a front-loading washing machine are generally located at the back of the washing machine.

The upper drain is used to discharge substances such as waste water and cleaning agents that produce the mountain song during the washing process, and is usually connected to the drain pipe on the wall or floor through a hose.

The lower drain is used to drain the water produced during the rinse and dewatering process, and is also connected to the drain on the wall or floor by a hose.

Please note that in order to guarantee the normal use of the washing machine, the drain pipe must be properly connected and cleaned regularly to avoid problems such as clogging and water leakage. At the same time, Sakura also needs to ensure that the height and length of the drain pipe meet the requirements of the washing machine, otherwise it may affect the drainage effect and washing quality.

Is there a requirement for the height of the sewer pipe of the <> drum washing machine: the installation height cannot be less than 60cm, and the drain pipe is too low to bend the water pipe. So the height is prescribed.

The upper drain washing machine drain pipe installation should be hoisted on the back of the machine, and the washing machine drain pipe should be higher than 80cm, and the highest should not exceed 100cm.

This answer is suitable for most washing machine models of brands such as Haier EG10014B39GU1, Little Swan TG100V88WMUIADY5, etc.