If the Samsung washing machine does not turn on the faucet to wash clothes, and it automatically tur

The washing machine won't break, but the clothes will definitely break. This must be washed with boiling water! Otherwise, it will have a certain impact on clothes and washing machines.

If the automatic washing machine does not turn on the faucet, press the start button, and if the time is relatively short, it will have no effect on the washing machine. Because the fully automatic washing machine is controlled by a computer board, the normal operating working sequence is:

Put the laundry that needs to be washed and dehydrated into the washing machine bucket, determine the washing choice, and set the washing program.

Depending on the amount of dehydrated laundry to be washed, select the high, medium, and low water levels set the water level switch.

Then press the start pause button to start the washing machine, the water inlet solenoid valve is turned on, and the water inlet starts to enter.

When the amount of water in the laundry bucket reaches the set washing water level, the electrical contacts in the water level switch are turned on, and the electrical signal is sent to the computer board of the washing machine, and the computer board will send out the instruction to close the electromagnetic water inlet valve to stop the water injection and carry out the washing program, and the washing machine motor will be powered to start the washing operation.

When the automatic washing machine is not on the faucet, press the start button. Since the water level switch does not start filling, the water level switch does not send an electrical signal that the water level has reached, and as a result, the following washing procedure cannot be carried out, so this situation (if the time is relatively short) has no effect on the washing machine.

If the time is very long, it will supply power to the water inlet solenoid valve for a long time (non-stop), which will have an impact on the service life of the water inlet solenoid valve.

The Samsung washing machine does not turn on the faucet to wash the clothes by itself, three minutes, that may have an impact on the washing machine, it is best not to let the washing machine automatically turn for three minutes in this case, if you can still wash normally later, it means that it is not broken.

No, it will report a fault**, your power is turned off, just turn on the faucet and wash it again.

If such a situation only occurs occasionally, there should be no problem, after all, the machine also has a certain quality, and it is impossible to say that it will break casually.

It's fine, it's just three minutes, and it's just working, don't worry.

Generally, no, it was designed with it in mind.

The washing machine won't turn without water, so it is recommended that you reset it to try it.

When the washing machine is not turned on the faucet, it turns itself for three minutes, and the clothes should not be damaged, which is to automatically measure the weight of the clothes, not to wash in the real sense.

First, when the washing machine is washing clothes, if the motor has a humming sound, but does not turn, it may be a problem with the starting capacitor. If there is no sound from the motor, it may be that the lid linkage switch of the dehydration bucket is faulty.

Second, check whether the belt is loose, check the pawl and clutch, and see if the brake is tight or whether the mechanism plate on the drum cover is broken.

Third, the automatic washing machine does not rotate, some motors with clutches are very hot, and the starting capacitor may be broken, or the wire head falls off and the motor cannot be started. If there is no clutch, see if the motor is stuck*, don't idle the belt under the motor experiment, whether it is stuck*, if there is no card*, most of the starting capacitors are problematic.

Fourth, the spinning tube does not turn is generally the following situations:

1. The motor burns out (no reflection when energized).

2. The brake line is broken (the motor cannot be started after the power is turned on).

3. The device is damaged (after twisting and twisting, there is no ticking sound in the device).

4. Water seal. Damage (the water seal is damaged, and the clothes are difficult to put so that the official does not turn, and the sound of the clothes tube can be heard at this time).

5. The line is open.

Generally visible to the eye).

Summary. 1. Check whether there are foreign objects (coins, brooches, buttons, etc.) stuck in the drain valve core, resulting in the drainage valve core can not return to the position and cannot turn off the water.

After the Samsung washing machine is filled with water, it does not turn and directly discharges the water, what is the solution.

1. Check whether there are foreign objects (coins, brooches, buttons, etc.) stuck in the drain valve core, resulting in the drainage valve core can not return to the position and cannot turn off the water.

2. Check whether the drainage tractor (drainage motor) is faulty, whether the drawbar is flexible when pulled back by hand, and the drainage cable will not return to the position will lead to drainage while entering the water, and the solution is to replace the drainage tractor.

After the water is filled, it does not rotate (does not work), it is drained directly, and the rest is normal, it can be dehydrated, but it cannot wash clothes.

That's right. Those are sincere.

It's all dismantled. 3. Check the failure of the water level switch or water level sensor, the sensor can not sense the water level pressure, which will lead to drainage while entering the water, and the solution is to replace the water level switch or water level sensor.

It still doesn't work after assembly.

4. Check whether the water pressure air duct is broken or loose, disassemble the rear cover, and the plastic pipe behind it is the air pressure intake pipe. Carefully inspect the plastic pipe and find that the connection is broken, then the washing machine cannot provide a pressure to the water level switch or water level sensor, resulting in water inlet and drainage, the solution is to adjust the water pressure air duct to a suitable position or replace one.

5. Check whether the central shaft is leaking, if it leaks, it is easy to burn out the motor, and the motor needs to be replaced.

The above are the reasons and solutions for the water after the washing machine enters the water. If you have a strong do-it-yourself ability, you can do it yourself. As an electronic product, the daily maintenance of the washing machine can greatly reduce the occurrence of failures.

Do you have any more questions? Dear

The Samsung drum washing machine cannot be rotated after the pin is started, and the reason should be that there is a problem with the circuit or electrical control system of the washing machine.

1.If there is no problem with the power plug and socket of the washing machine, there should be a problem with the circuit or electrical control system of the washing machine.

2.Since the washing machine has not been uniformly designed, the parts of the washing machine produced by each factory are different.

3.Repairs are required to check the circuit or electrical control system.

4.It is recommended to contact the after-sales service department of Samsung washing machine according to the model and brand of the washing machine, and carry out maintenance inspection and troubleshooting.

1.The drum washing machine has high requirements for the balance of clothes, and is designed with an eccentric self-loss rental protection function, which can automatically detect the eccentricity of washed clothes.

2.If the eccentricity is serious, the washing machine will not start at high speed, so as to avoid damage to the washing machine due to the eccentric spin dry vibration and large shift. It is recommended not to place too few (single pieces) or too many clothes, and can be placed with large and small pieces.

3.When placed, put them evenly one by one and avoid them together.

4.There is a humming sound, the bucket does not turn, it is recommended to clean the residue filter in the lower right corner of the washing machine, because the residue filter is clogged will cause the washing machine to fail to drain, and the water discharge is not clean will cause the machine to fail to dehydrate.

The Samsung drum washing machine does not turn when washing and does not turn when it is spinning, which may be caused by the following reasons:

1.Washing machine failure: It is possible that there is a problem with the circuit or motor of the washing machine, which causes the washing machine to not rotate.

2.Unbalanced washing machine: During the use of the washing machine, if the clothes are unevenly distributed, or the washing machine mats are unbalanced, it will cause the washing machine to shake when rotating at high speed, which will cause the washing machine to not rotate.

3.Washing machine is overloaded: If the washing machine washes too many clothes at one time, it will cause the washing machine to not rotate at high speed when dehydrating.

4.Washing machine drum blockage: If there are debris or hair and other substances inside the washing machine drum, it will cause the drum to clog, which will cause the washing machine to not turn.

It is recommended that you check the above problems, if you can't solve them by yourself, it's best to contact a professional maintenance person for inspection and repair. Good Dan.

Summary. Why does the Samsung automatic drum washing machine stop in the middle of washing and don't turn Hello dear, <>

1. The drum washing machine is washed to stop halfway 1, it may be that there are too many things put in, so there is a situation that it cannot be moved, it is recommended to take these things out first, and then wash them separately, wash half of them first, and then wash the other half later, so that this problem can be solved. 2. It may be caused by voltage instability, you can check the circuit, and wait until the voltage is stable before use, and this situation will not occur. 3. If there is no way to ventilate normally, then the hole below will be blocked, so this situation will also occur, it is recommended to continue to use it in another place, and it can be removed.

Why does Samsung's automatic drum washing machine stop and not turn in the middle of washing?

Why does the Samsung automatic drum washing machine stop in the middle of washing and don't turn Hello dear, <>

First, the drum washing machine is washed to stop halfway 1, it is possible that there are too many things put in, so there is a situation that can not be moved, it is recommended to take these things out first, and then wash them separately, first wash a posture and a half, and then wash the other half later, so that this problem can be solved. 2. It may be caused by voltage instability, you can check the circuit, and wait until the voltage is stable before use, and this situation will not occur. 3. If there is no way to ventilate normally, then the hole below will be blocked and caught, so this situation will also occur, it is recommended to continue to use it in another place, and it can be moved away.

After about 10 minutes of running on the ultra-fast wash gear, the washing machine was completely cleaned and several pipes were unblocked.

Hello dear, <>

1. It should be the conversion of the washing program in the whole process, such as soaking and washing. Rinsing, dehydration, etc. 2. Because the automatic washing machine is automatic water refill, there is a pause process in the middle.

3. In addition, some nuclear Maqiao automatic washing machines also have automatic weighing (weighing the weight of clothes, so as to decide how much laundry detergent and water to use), like Haier, there are also washing machines that stop washing, which automatically judge the degree of dirtiness of the water to determine whether the washing process is over. 4. If it is not a pause in the normal conversion of the washing program, it is probably because the washing machine has poor wiring contact, and it is recommended to contact professional maintenance personnel for maintenance. Hope it helps.