How to tear off the label without leaving glue How to tear off the label without leaving glue

Cover the part of the trademark on the utensils with a napkin, pour white vinegar on the napkin, let it stand for 10 minutes, and then remove the logo to easily remove it. Tear off the top layer of the label on the object, and then wipe the remaining stickers with an eraser.

If you use your fingers, you can try to use your fingers to "pinch the adhesive residue on the label into small balls". Check how sticky the label residue is. If it's really sticky, don't try this method, or it will only make it worse.

Hot water method. Our labels are generally glued with self-adhesive, as long as the temperature is hot enough, the glue will be very easy to tear off after it has melted again.

1. Hair dryer blowing: Adjust the hair dryer to the hot air shield, and then blow on the label for a while, and you can easily tear the label off.

2. Soak with liquor: pour liquor or alcohol on a paper towel, apply the label with a paper towel, and the alcohol component can dissolve the organic glue inside the label, so that the label can be easily removed.

3. Apply air oil essence: evenly apply wind oil essence on the label, and after standing for one minute, you can easily remove the label and offset printing.

4. Apply hand cream: hand cream has an interface active agent and a softener, and the interface active agent can separate the adhesive from the adhered object. Simply apply the hand cream to the sticker, wait 5-10 minutes, and when the sticker is softened and soaked, you can remove the sticker.

Since the adhesive used in the label is not resistant to high temperatures, it is baked with a warm air from a hair dryer first, and then the stickiness of the label or seal can be removed cleanly without leaving any trace.

Removing self-adhesive alcohol, gasoline or nail polish, hand cream, and other dilutions can help remove these stickers easily and thoroughly. The method is to tear off a layer of paper on the surface of the label, apply alcohol or gasoline, etc., and then rub the surface with your hands to make it fully soaked in the self-adhesive, and finally wipe it off with a cloth. However, with these solvents, it is also possible to cause damage to the surface of the utensils.

A better way is to soak the self-adhesive part with hot water or blow the self-adhesive part with a hair dryer, and then rub it with a damp cloth to remove the self-adhesive.

1. Use an eraser.

Principle: Rely on the rubber to fuse the self-adhesive glue.

Method: Use the eraser to wipe constantly, the place with glue will turn black at the beginning, but the glue will slowly fall off after wiping for a long time.

Advantages: easy to operate, quick effect Disadvantages: average effect.

2. Use a hair dryer.

Principle: Rely on heat to remove self-adhesive.

Method: Use a hair dryer hot air gear, at a distance of about 10cm from the sticker, and blow directly with hot air; After blowing for a while, slowly remove the self-adhesive label while blowing.

Advantages: easy to operate, good effect, quick effect.

Disadvantages: It is not suitable for soft plastics that are not heat-resistant, and the high temperature can easily deform the object.

3. Use edible vinegar.

Principle: Similarity compatibility principle.

Method: Dip a dry dishcloth in white vinegar or vinegar and completely cover the area with the label so that it is completely soaked. After maceration for 15-20 minutes, gradually wipe off with a dishcloth along the edges of the sticker, and finally soak it in water for a while.

Advantages: suitable for self-adhesive on tableware such as bowls and chopsticks, non-toxic and harmless.

Disadvantages: Slightly less effective in decontamination.

4. Use edible oil.

Principle: Similarity compatibility principle.

Method: Apply the cooking oil evenly on the place where the label is applied, wait for 3 to 5 minutes, and then slowly tear it off directly from the corner of the label by hand, so that there will be no label marks.

Advantages: glass, stainless steel and other hard objects have good decontamination effect.

Disadvantages: The effect of removing other objects self-adhesive is not good.

5. Use lemon juice.

Principle: Similarity compatibility principle.

Method: Squeeze lemon juice on the hands with sticky adhesive dirt and rub it repeatedly to remove the self-adhesive marks.

Advantages: It is suitable for removing sticky adhesives from the hands and will not cause any damage to the skin.

Disadvantages: The effect of removing other objects self-adhesive is not good.

6. Use alcohol.

Principle: Similarity compatibility principle.

Method: Use an alcohol-soaked rag to completely soak the part with the self-adhesive label, wait for a while, and slowly wipe the self-adhesive label from the edge to the middle with the alcohol-soaked rag until all the self-adhesive is removed.

Advantages: glass, stainless steel and other hard objects have good decontamination effect.

Disadvantages: Alcohol is not easy to obtain, and there is some damage to the skin of the hands.

7. Use wind oil essence.

Principle: Similarity compatibility principle.

Method: Completely soak the place with self-adhesive with wind oil essence, and wipe it off vigorously with a dry rag after 15 minutes. If the dirt is difficult to remove, you can extend the soaking time of the wind oil essence and then rub it vigorously until it is clean.

Advantages: Almost all items are not damaged, especially on printed and painted surfaces.

Disadvantages: Decontamination takes a little longer.

After the item is purchased, the self-adhesive label should be removed as soon as possible, if the time is long, the solvent in the self-adhesive label glue has completely volatilized, and it is more difficult to remove it.

Hand cream can be used to quickly remove the glue left behind by the label. Apply the hand cream to the glue and let it sit for 20 minutes before it can be wiped off with a towel, here are the steps:

Tools needed: towel, hand cream.

1. First of all, you can see that there is an obvious label mark on the outside of the glass bottle.

2. Apply a layer of hand cream to the area where there are glue marks.

3. Wait for 20 minutes to allow the hand cream to fully penetrate into the glue marks.

After a few minutes, wipe it with a towel.

5. The visible glue marks are wiped cleanly, leaving no traces.

Notes:1. Let it stand for a longer time, so that the hand cream can penetrate more fully and be easier to remove.

2. If you don't have hand cream, you can also use alabaster instead.

How to remove the glue left by the label:

1. Hand cream.

If you can't find alcohol, gasoline or nail polish diluent at home, you can try hand cream, many hand creams on the market contain glycerin, silicone, natural active agents, the above ingredients reed hail has the ability to wet, penetrate and dissolve the self-adhesive, and can quickly penetrate between the self-adhesive and the surface of the object, so as to achieve the purpose of removal.

2. Nail polish remover and nail polish.

For self-adhesive marks on the surface of hard objects, such as stainless steel basins or glassware, first remove the large piece of trademark paper, use a cotton swab dipped in a small amount of nail polish remover to apply to the label residue, wait for a few minutes, and then wipe it back and forth with a soft cloth to remove it, because nail polish remover is very corrosive, it cannot be used on the surface of items that are afraid of corrosion, such as lacquered furniture, laptop shells, etc. Nail polish, nail polish diluent has a stronger solvency than alcohol and gasoline, and can be applied to the label to dilute and dissolve those non-sticky adhesives.

3. Edible oil.

If you want to remove the self-adhesive label on the general object, wipe it with cooking oil will work, many self-adhesive label glue generally belongs to the pressure-sensitive adhesive of polyacrylate, which can swell in oil due to the non-polar molecule. Scoop some oil with a small spoon and spread the oil evenly over the label, and after 4-5 minutes, you can slowly tear it off from the corner of the label by hand.

1. Use a hair dryer.

When tearing off the label, it is best to let the adhesive peel off along with the label. We can use a hair dryer to blow hot air on the edge of the label, blow around for about 1 minute, and then tear it while blowing. This makes it easy to tear off not only the entire label, but also the adhesive.

2. Wet towel.

Because of the long time, it is difficult to remove the general offset printing. We can soak the areas with offset prints with a damp towel and then wipe them slowly, but this method is limited to areas that are not afraid of sticky and watery ingress.

3. Potpourri oil or wind oil essence.

If you have potpourri oil or wind oil essence at home, you can also try this method. Apply potpourri oil or wind oil essence to the remaining adhesive and let it sit for 1-2 minutes, then wipe off the adhesive with a cloth.

4. Dish soap.

Dish soap also has the effect of removing traces of clear glue, take some dish soap with a rag and wipe it gently.

5. Hand cream.

If you have hand cream at home, you can also use it to remove the adhesive. Apply the hand cream to an area of adhesive and let it sit for 1-2 minutes, then wipe off.

Notes:

1. It is best to dispose of the glue left after the label is torn off as soon as possible, and the sooner it is processed, the easier it is to deal with.

2. In fact, you can bake the label with fire or blow the label with a hair dryer before tearing the label, which can quickly clean the offset print.

When you buy a commercial house, many goods will be labeled, many consumers will choose to tear off the product label in order to make the product more beautiful, but the label is usually very tight, we will leave some glue when we tear off the label, so how to remove the glue left by the label? I'll introduce you to the next one.

1. If the product is soaked in water and will not be damaged, you can fill the container with hot soapy water, soak the product for a period of time, the remaining label and viscose on the product will soften and fall off, you can wipe it clean with a cloth; Or we can wipe the residual label with some rubbing alcohol and vinegar and rubbing it until it is completely clean; You can use a paper towel to stick some cooking oil to wipe off the residual label. However, it should be noted that cooking oil should not be used to remove the adhesive from porous labels; Vinegar cannot be used to remove viscose from metal, marble surfaces.

2. If you want to remove the adhesive left on the product label, you can use a hair dryer to blow the adhesive for a few minutes, and you can easily tear off the adhesive; Or we use a hard card to scrape off the label, if there is still a residual label, you can use an eraser to wipe it clean. You can also wrap a circle of tape on your index finger, pay attention to the glue surface to face outward, and you can get rid of the remaining adhesive on the product by pressing and pulling the residual adhesive with the glue surface.

3. You can also dip some nail polish remover on the paper towel, gently wipe the residual label, and easily clean up the adhesive. We can also spread mayonnaise and peanut butter on the viscose, and after a period of time, vigorously wipe off the remaining viscose. It is important to note that mayonnaise cannot be used to wipe the viscose of porous materials such as wood.

Summary: As for how to remove the glue left by the label, I will briefly introduce it to you here. I hope that after reading this article, you will be able to understand this. When removing viscose, if the product is more complex, it is easier to leave marks on the surface of wood and other surfaces.